LTD7204-WH, LTD7208-WH and LTD7216-WH series DVR. DVR Pre-Installation The LTD7200-WH Series DVR is highly advanced surveillance equipment that should be installed with care. Please take into consideration the following precautionary steps before installation of the DVR. 1. Keep all liquids away from the DVR.
Page 3
Quick Operation Guide of LTD7200-WH Series DVR 3. Connect the HDD to the motherboard of the DVR with the included data cable. 4. Connect the power cable to the HDD. 5. Re-install the cover of the DVR and fasten screws.
Quick Operation Guide of LTD7200-WH Series DVR Front Panel The front panel of LTD7200-WH is shown below: Table 1 Description of Control Panel Buttons Name Function Description POWER indicator turns green when DVR is powered up. POWER STATUS indicator lights in red when data is being read from or written to STATUS HDD.
Page 5
Quick Operation Guide of LTD7200-WH Series DVR Table 2 Description of Rear Panel Item Description VIDEO IN BNC connector for analog video input. BNC connector for video output. VIDEO OUT Connects USB mouse or USB flash memory devices. USB Interface HDMI HDMI video output.
Quick Operation Guide of LTD7200-WH Series DVR HDD Storage Calculation Chart The following chart shows an estimation of storage space used based on recording at one channel for an hour at a fixed bit rate. Bit Rate Storage Used 128K...
Quick Operation Guide of LTD7200-WH Series DVR Menu Operation Menu Structure The menu structure of the DVR is shown as below: Startup and Shutdown Proper startup and shutdown procedures are crucial to expanding the life of the DVR. Before you start: Check that the voltage of the extra power supply is the same with the device’s requirement, and the ground...
Quick Operation Guide of LTD7200-WH Series DVR 2. Click the Shutdown button to enter the following dialog box: 3. Click the Yes button. The following message box pops up: 4. Turn off the power switch on the rear panel of DVR.
Page 11
Quick Operation Guide of LTD7200-WH Series DVR 2. Check the checkbox to enable Setup Wizard when device starts. Click Next to continue the setup wizard. You can also click Cancel to exit the Setup Wizard, or use the Setup Wizard next time by leaving the “Start wizard when device starts?”...
Page 12
Quick Operation Guide of LTD7200-WH Series DVR 5. Click Next button which takes you back to the Network Setup Wizard window. Set the network parameters, including the NIC type, IPv4 address, IPv4 subnet mask, default gateway, etc. You can enable the DHCP to automatically obtain an IP address and other network settings from that server.
Page 13
Quick Operation Guide of LTD7200-WH Series DVR 7. Click Next button to enter the Record Settings window. Select the camera to configure. Check the checkbox to enable Start Recording. Select the recording mode to Normal or Motion Detection. Click Copy to copy the record settings of the current camera to other camera (s) if needed.
Quick Operation Guide of LTD7200-WH Series DVR Click OK to return to the Record Settings window. Click OK to complete the startup Setup Wizard. Live View Some icons are provided on screen in Live View mode to indicate different camera status. These icons include:...
Quick Operation Guide of LTD7200-WH Series DVR Table 3 Mouse Operation in Live View Name Description Menu Enter the main menu of the system by right-clicking the mouse. Single Screen Switch to the single full screen by choosing channel number from the dropdown list.
Page 16
Quick Operation Guide of LTD7200-WH Series DVR Control icon to enter the PTZ toolbar. Table 4 Description of the PTZ toolbar icons Icon Description Icon Description Icon Description Direction button and the Zoom+, Focus+, Zoom-, Focus-, auto-cycle button Iris+ Iris-...
Quick Operation Guide of LTD7200-WH Series DVR 2. Click the Start Recording submenu and select the recording mode to Normal Record or Motion Detection Record. 3. In the pop-up message box, click Yes to finish the quick recording settings for all channels.
Page 18
Quick Operation Guide of LTD7200-WH Series DVR Mouse: right-click a channel in live view mode and select All-day Playback from the menu. Press PLAY button on the IR remote control to play back record files of the channel under single-screen live view.
Page 19
Quick Operation Guide of LTD7200-WH Series DVR Backup Recorded files can be backed up to various devices, such as USB flash drives, USB HDDs or a DVD writer. To export recorded files: 1. Click Menu>Export to enter Video Export interface.
Page 20
Quick Operation Guide of LTD7200-WH Series DVR 3. Check backup result. Choose the record file in Export interface and click the button to check it. 0202011021120...
Need help?
Do you have a question about the LTD7200-WH Series and is the answer not in the manual?
Questions and answers