Page 2
Go-Go Babyz will repair or replace, at its sole option, the defective product within that one-year time period. If you have a problem with your Go-Go Babyz product or are not satisfi ed with it, please contact Go-Go Babyz Customer Service at 1.888.686.2552.
& Fisher Price ....10 ® Instructions for Attaching to Recaro ........11 Instructions for Attaching to the Evenfl o Triumph ....12 Commercial Airlines, Car Seats and the gogo Kidz Travelmate ..13 Care and Maintenance ..............14 TABLE OF CONTENTS...
WARNING: DO NOT LEAVE THE GOGO KIDZ ATTACHED TO A CAR SEAT WHILE DRIVING IN AN AUTOMOBILE. THE GOGO KIDZ HAS NOT BEEN TESTED IN COMBINATION WITH THE CAR SEATS IN ANY CRASH TESTING PROGRAM AND INJURY TO YOUR CHILD COULD OCCUR.
Page 5
Kidz. WARNING: DO NOT ALLOW CHILDREN TO CLIMB INTO OR OUT OF THE CAR SEAT WHILE GOGO KIDZ IS SECURED, UNLESS YOU ARE HOLDING THE GOGO KIDZ AND INSTRUCTING THE CHILD. WARNING: NEVER USE THE GOGO KIDZ ON STAIRWAYS OR ESCALATORS.
What's Included Please refer to this page during any part of the assembly instructions and attaching instructions. You will use the following parts to assemble the gogo Kidz™ Plate: Plate with axle, wheels and push caps already assembled Handle Handle Screws Plate with axle, wheels and You will use the following parts for attaching the gogo push caps...
NOTE: It is important that the handle be orientated properly before insertion into the openings of the gogo Kidz plate. There are two ways to make sure the handle is inserted correctly. 1. There is a rivet in each leg of the handle (at the bottom on one side).
fi t with the gogo Kidz. If you do not see your car seat listed on the product box or manual, please check our web site to see if we have had to opportunity to test it with the gogo Kidz.
Align the two support tabs on the back side of the gogo Kidz plate to the bottom of the car seat and lay the gogo Kidz plate on the back of the car seat. (Please refer to general information if you are having diffi culty) Make sure tabs align with ribs 3.
3. Align the plate. Align the support tabs at the bottom of the gogo Kidz plate with the bottom of the car seat and lay the gogo Kidz plate on the back of the car seat. 4. Insert thumbscrews.
2. Attach the j-bolt. Hook the j-bolt over the L-shaped metal rod on the side of the Recaro® seat and align the gogo Kidz plate so the threaded end of the j-bolt goes through the middle hole on the side of the plate.
Attach Cleat Once the retainer bar been attached to the plate and the gogo Kidz is secure, lift the car seat and pull the gogo Kidz into the upright position. Test the connection by pulling on the handle and moving the gogo Kidz side to side.
Kidz™ Travelmate The gogo Kidz is 16 ½ inches wide and fi ts down the aisle of most commercial airplanes. However, many car seats are wider and they may not fi t down the aisle of the coach section. A practical approach is to have your child out of the seat and expect to carry the seat to your assigned seat, once you reach the coach section.
Care & Maintenance Before connecting the gogo Kidz to your car seat, make sure the unit is assembled correctly and all parts and fasteners are secure. After assembly pull horizontally on the back of the gogo Kidz to make certain the guides are aligned properly and there is no slippage.
Kidz Travelmate! ™ Our goal for Go-Go Babyz is to offer innovative, high quality and safe products to make life easier when you and your baby are “on the go.” We welcome suggestions and comments. Go-Go Babyz is dedicated to making our current products and features easier to use.
Page 16
Young Style are trademarks of Keiper Recaro Group. The Go-Go Babyz® product illustrated here is not approved by or manufactured under license from Britax Child Safety, Inc, Dorel Industries, Inc., Evenfl o Company, Inc., Keiper Recaro Group, Mattel, Inc., Graco Children’s Products and/or their affi liates. Go-Go Babyz Corporation is not affi...
Need help?
Do you have a question about the gogo Kidz and is the answer not in the manual?
Questions and answers