Table of Contents
Advertisement
Quick Links
Elumenati OmniFocus 200 Series
Installation and Operation Guide
Last updated: November 2012
This document applies to the OmniFocus 3020 and 30210 sold after January 2013.
For all previous 200 Series products please refer to the "OmniFocus 200 Series
pre2013" manual.
For brevity, we refer to the 200 Series throughout. Differences are noted where applicable.
Elumenati OmniFocus 200 Series .................................................................................1
Installation and Operation Guide..................................................................................1
200 Series Overview...................................................................................................2
Introduction...........................................................................................................2
Equipment List.......................................................................................................2
200 Series Setup........................................................................................................3
Projector Connection...............................................................................................3
Lens Installation.....................................................................................................4
First Light..............................................................................................................5
Projector Settings Adjustment..................................................................................5
Stand Assembly (Optional)......................................................................................7
200 Series Information...............................................................................................8
Maintenance..........................................................................................................8
Troubleshooting......................................................................................................8
Product Support.....................................................................................................8
200 Series Product Specifications.................................................................................9
Elumenati, GeoDome OmniFocus and OmniMap are all trademarks of The Elumenati LLC.
Immersive Projection Design -
www.elumenati.com
i nfo@elumenati.com
www.elumenati.com
Advertisement
Table of Contents
Summary of Contents for Elumenati OmniFocus 200 Series
-
Page 1: Table Of Contents
Last updated: November 2012 This document applies to the OmniFocus 3020 and 30210 sold after January 2013. For all previous 200 Series products please refer to the “OmniFocus 200 Series pre2013” manual. For brevity, we refer to the 200 Series throughout. Differences are noted where applicable. -
Page 2: 200 Series Overview
4. 200 Series stand (optional) (Fig. 2) Assembled 30200 on stand (Fig. 1) Case has two layers: Stand (top) and Projection System (bottom) Immersive Projection Design - www.elumenati.com Elumenati, GeoDome OmniFocus and OmniMap are all trademarks of The Elumenati LLC. -
Page 3: 200 Series Setup
The following describes the setup procedure. Projector Connection Before attaching the Elumenati lens, set up and/or install the projector and connect the pro- jector to the video source. Please refer to the WUX4000 manual for details on projector op- eration. -
Page 4: Lens Installation
(extended displays mode). Default resolution is 1920 x 1200. It may be helpful to use either the truncated or fulldome Elumenati alignment image as your desktop background. Again use desktop settings to change your background making certain that the image is displayed 1:1 and not stretched or tiled. -
Page 5: First Light
(180°x112°) projection mode as well as the nominal Zoom and Lens Shift settings. (Fig. 6) Nominal Display and Focus settings for truncated projection. Immersive Projection Design - www.elumenati.com Elumenati, GeoDome OmniFocus and OmniMap are all trademarks of The Elumenati LLC. - Page 6 (Fig. 8) runs the extent of and is parrallel to the screen edge. ● Use Lens Shift to make final minor adjustments to the alignment. Immersive Projection Design - www.elumenati.com Elumenati, GeoDome OmniFocus and OmniMap are all trademarks of The Elumenati LLC.
-
Page 7: Stand Assembly (Optional)
● Option 3: The easiest to assemble but with a fixed height setting. (Option 1) 9” height adjustment (Fig. 9) Fully Assembled Stand (Option 3) Easiest mounting (Option 2) 3" height adjustment Immersive Projection Design - www.elumenati.com Elumenati, GeoDome OmniFocus and OmniMap are all trademarks of The Elumenati LLC. -
Page 8: 200 Series Information
Discard the tissue after every use. Troubleshooting Product Support Please contact us with your questions via email at support@elumenati.com or phone at 1- 888-384-3826, extension 2. Immersive Projection Design - www.elumenati.com Elumenati, GeoDome OmniFocus and OmniMap are all trademarks of The Elumenati LLC. -
Page 9: 200 Series Product Specifications
• RS-232C Control Terminal • Optional LAN Adaptor LIMITED WARRANTY • 1 year parts and labor • Lamp: 120 days or 500 hrs, whichever comes first Immersive Projection Design - www.elumenati.com Elumenati, GeoDome OmniFocus and OmniMap are all trademarks of The Elumenati LLC. - Page 10 (Fig. 11) 30200 straight lens minimizes interference in traditional planetarium installations. (Fig. 12) 30210 features a folded lens minimizing the overall fm factor. Immersive Projection Design - www.elumenati.com Elumenati, GeoDome OmniFocus and OmniMap are all trademarks of The Elumenati LLC.
Need help?
Do you have a question about the OmniFocus 200 Series and is the answer not in the manual?
Questions and answers