Summary of Contents for Infinity Club 1200
- Page 1 Club INFINITY 1200 Professional 1200W discharge scan-light USER’ S MANUAL release 1.0 This manual must be considered an integral part of the projector.
-
Page 2: Table Of Contents
BEFORE CONNECTING AND USING THE PROJECTOR, IT IS IMPORTANT TO READ CAREFULLY ALL THE INSTRUCTIONS IN THIS MANUAL. QUALIFIED PERSONNEL ONLY, IN COMPLIANCE WITH ALL THE SECURITY LAWS, CAN DO THE INSTALLATION, THE MAINTENANCE AND THE UTILISATION OF THIS PROJECTOR. BEFORE CONNECTING THE PROJECTOR, MAKE SURE THAT THE FREQUENCY AND THE VOLTAGE VALUES ARE SUITABLE AS SPECIFIED ON THE PROJECTOR. -
Page 3: General Description
GENERAL DESCRIPTION As shown in Figure, the INFINITY CLUB 1200 is made up of the following parts: 1. Rear panel 2. Cooling unit 3. Auxiliary support 4. Anchoring bracket 5. Lamp compartment 6. Lid 7. Projector body 8. Swivelling head 9. -
Page 4: Description Of Parts And Controls
8. Serial number plate 9. Rear handles Adjustment of Projector Body Angle As shown in Figure, the INFINITY CLUB 1200 projector can be adjusted between 0 ÷ 50° compared to its anchoring bracket. - Loosen lateral knobs. - Place the projector at the desired angle. - Page 5 Rotate the projector head to the desired angle. Firmly tighten knob “A”. Modular construction As shown in the picture, the INFINITY has a modular construction for ease maintenance. (MSZ in the picture) HANDLE WITH CARE!!! Loosen the knobs of the top lid and remove it.
-
Page 6: Start-Up Procedures
START-UP PROCEDURES Positioning and Installation Follow these steps for opening the package and installing the projector on its working position: · Place the projector near the place it will be installed. · Open the package and remove anchoring elements and accessories. ·... -
Page 7: Power Supply
To make sure the projector functions properly, the dip-switches in the DMX ADDRESS AREA, on the rear panel, must be correctly configured. Keep in mind that each INFINITY CLUB 1200 occupies a minimum of 10 to a maximum of 12 DMX channels (10 channels when it operates in the Standard Operating Mode, 12 when the PERSONALITY dip-switch 01 is set to ON, enabling the HIGH DEFINITION 16bit function). - Page 8 Gobos replacement As shown in the figure, it is very easy to replace gobos on the wheel. When the projector is cold, follow these steps: -Disconnect the power supply. -Wait at least 20 minutes to be sure the projector components are cold. -Loosen the knobs on the top lid and remove it.
-
Page 9: Dmx Channel Assignment
DMX CHANNELS ASSIGNMENT FUNCTION COLOUR 1° GOBOS WHEEL GOBO INDEX + ROTATION EFFECTS WHEEL EFFECTS INDEX + ROTATION DIMMER SHUTTER SPECIAL FUNCTIONS PAN (coarse) TILT (coarse) 2° PAN (fine) (when 16 bit HIGH DEFINITION 2° TILT (fine) SCANNING option is enabled) Note: Is also available the following 16 bit option PAN (coarse) PAN (fine) - Page 10 CHANNEL 2 = GOBO WHEEL percent values decimal values 0 > 20 % GOBO 1 (OPEN) 0 > 51 20.4 > 40 % GOBO 2 52 > 102 40.4 > 60 % GOBO 3 103 > 153 60.4 > 80 % GOBO 4 154 >...
- Page 11 CHANNEL 6 = DIMMER percent values decimal values BLACK-OUT 0 % > 100 % INCREASING DIMMER LEVEL 0 > 255 100 % OPEN =255 - OPTION: PERSONALITY DIP-SWITCH N° 05 in position ON OPEN 0 % > 100 % DECREASING DIMMER LEVEL 0 >...
- Page 12 CHANNEL 9 = PAN percent values decimal values LEFT 100 % RIGHT =255 - OPTION: PERSONALITY DIP-SWITCH N° 03 in position ON RIGHT 100 % LEFT =255 (16 bit HIGH DEFINITION DMX with dip-switch n° 01 in position ON) CHANNEL 10 = TILT percent values decimal values 100 %...
-
Page 13: Optical System
OPTICAL SYSTEM The INFINITY CLUB 1200 is provided with a high-efficiency optical system made of double-coated antiflare lenses. This system lets INFINITY CLUB 1200 project an homogenous light beam, with 28° beam angle, ideal for disco and club. TROUBLESHOOTING PROBLEM... -
Page 14: Maintenance
MAINTENANCE CAUTION Safety guards, lenses, and filters must be replaced if they are visibly damaged to the point that they become ineffective (for example, if they have deep slashes or cuts). The lamp must be replaced if damaged, cracked, or deformed by the heat. PLANNED MAINTENANCE at user’s charge and responsibility OPERATION... - Page 15 M2 - OPTICAL EFFICIENCY TEST Use the controller to focus the beam on a flat surface, keeping the Iris and Dimmer at 100%. If the spot is not homogeneous, follow these steps: - Remove knob A, making sure the projector keeps its current position. - Insert a screw driver in the hold and turn clockwise or counter clockwise to optimise the horizontal position of the lamp compared to the optical system.
-
Page 16: Spare Parts
Mirror with support WARRANTY INFINITY is guaranteed against any manufacturing defects or material flaws. If defects or breakdowns occur during the warranty period, the manufacturer, directly or through its agents. After inspection and according to its own unquestionable judgment, the manufacturer will repair or replace the defective part.