Cirago International Limited is not responsible for any damage or loss of data deemed to be caused by its products. It is highly recommended that users conduct necessary...
Thank you for purchasing the Cirago Network USB Storage Link NUS2000. This device enables sharing files with users in your network easily. Simply insert your USB storage into the NUS2000, connect the device to your network, configure some basic settings, and you are ready to share your files on your NUS2000.
2. Hardware & Installation The Front Panel Display Power: Indicates the power is on LAN: ON - network connected to switch / hub Blink - indicates live network activity. USB 1-4: On when a USB device plugged into the corresponding ports. They also act as status indicators: Power Up >...
The Back Panel DC Power Jack: Socket for DC Power Plug 5V, 2A LAN Port: Gigabit 10/100/1000 Ethernet socket USB 1-4 Socket: USB type A connectors...
Page 8
Installation Please follow the following steps to install your NUS2000. Step 1. Connect the Ethernet cable to the network switch and USB NAS Step 2. Connect the USB device to the NUS2000 Step 3. Connect the power adaptor Step 4.
- “NUS2000” is the factory default name. The name given to the NUS2000 can be changed from the setup menu. If the name is changed, please use the new name to access it. If your computer’s UPnP is enabled you can search your Network Neighborhood for the NUS2000.
Page 10
After entering the login information, the web interface for the NUS2000 will be displayed. Configuring the settings of the NUS2000 can be done from the Tools menu. Select Storage Tools to view and format any connected USB devices. A partition information table will be displayed Format the partition the drives to NTFS, FAT32 or EXT2.
Page 11
11. Alternatively, you can access the Web Admin through your iPhone or iPad. Just start the Safari browser and type http://nus2000.local:1010, then enter the “admin” user and password. 12. To get remote disk access, you need to register your account on www.ciragolink.com...
4. Detailed Functions The Admin page has the left menu showing the selection. Clicking that row or the triangle in front of the menu item, the list will expand to have display the sub-menu. 4.1. Status Select STATUS from menu on the left. Information This page displays the general information of the hardware setup and the specific server information as shown below.
NUS2000 and shows the submenu. Server This page shows the name of the NUS2000 so that you can access the unit in the Windows network by its name instead of using the IP address that may be changed if you are using DHCP (IP address distribution).
Page 14
DNS servers that your ISP recommends. Time Zone The NUS2000 uses the network time server to synchronize its clock. Select time zone and daylight savings options and hit Apply to save settings. NOTE: You can choose from the two NTP servers provided or you can enter your specific NTP server name NOTE: Reboot the device to permanently activate any changes made.
Page 15
Password The default administrator password is “000000”. Changing this to an alphanumeric password is recommended. This is most important to change that password and create the users list especially when you enable your NUS to connect to the CiragoLink Service Users Add new users using this feature.
4.3. File Server The NUS2000 is able to share connected USB storage devices as a File server for other network users. The file server can be access by SMB (Samba) or WebDAV protocol. SMB is commonly used in PC environment, while WebDAV is used in Apple...
Page 17
The “.local” is the bonjour convention for the name of NUS2000 and the “:9880” is the tcp port number used for WebDAV. Chapter 7 has more detail information on the setup and usage of the WebDAV client...
If the iTunes Server is running, the button on the left will show Rescan, otherwise it will show APPLY. Open iTunes on your PC or Mac and the NUS2000 will be displayed under the SHARED tab. The music from storage devices attached to the NUS2000 will be displayed.
Settings Select Enable for BT Download and then select the path for the download file. In NUS2000, you can also setup the total download and upload rate. Then click “Apply” to save your settings. Queue On the BitTorrent ->...
After the content has been downloaded, the device will automatically move the content to the subdirectory “Finished” under the Download Directory and the torrent will automatically be removed. The finished downloaded list can be seen under the “Completed” page under BitTorrent submenu. You can manually clear the list or when you select a new Download directory, the list will reset.
Page 21
It can however format multiple partitions if they have already been allocated before connecting them to the NUS2000. Using EXT2 formatted disks on a Windows PC may need the installation of additional software on the PC, such as “EXT2FSD”...
Reset button. Firmware This tool allows you to upgrade the firmware of the NUS2000. Click on Browse to select the firmware file to upload, and then click on Upgrade. The system will prompt you to confirm the upgrade.
5. Administration with iOS devices The NUS2000 can also be managed via iPhone or iPad. In iPhone, open Safari and type: http://nus2000.local:1010 The management flow is similar to that of the Web UI, except some functions are not applicable with iPhone, such as adding BitTorrent seeds.
Page 24
The screenshots show the add user and CiragoLink control, you can disconnect with the CiragoLink through a touch or associate the box with different user account in Ciragolink.com Server File sharing, assign a different folder path for different users, the default user “admin”...
Page 25
With BitTorrent service, you can change the setting path of the BitTorrent and review the download progress of the working torrents. Tools This section is different with the Web UI. It will only allow you to unplug the USB drive and show details of the storage item selected. The configuration and firmware upgrade settings are omitted.
6. Printer Installation The NUS2000 can act as USB Print Server. Following are instructions on how to install the printer on different operating systems. 1. Windows XP From the Start menu, go to Printer & Fax, then select Add Printer, the wizard will start.
Page 27
The wizard will lead you to the page “Configure Standard TCP/IP Port Monitor”. Just use default configuration of Protocol with “RAW” and Raw Settings Port Number with “9100” Click “OK”, then “Next” to complete the setup. Then the wizard will prompt you to select the printer driver to associate with this TCP printer port.
Page 28
IP address for the device. Enter the name of the device “NUS2000” or if the name of the device was changed during setup, enter the new name assigned to it. If you chose to enter a fixed IP address in the network setup, enter an IP address.
Page 29
Click “Next” to continue. Under Device, choose “Custom” and click “Settings”. The system will then prompt you to setup the TCP/IP Port Monitor. Just use default configuration of Protocol with “RAW” and Raw Settings Port Number with “9100” Click “OK” to continue. You will be prompted to select your printer.
Page 30
IP address for the device. Enter the name of the device “NUS2000” or if the name of the device was changed during setup, enter the new name assigned to it. If you chose to enter a fixed IP address in the network setup, enter an IP address.
Page 31
The system will then prompt you to setup the TCP/IP Port Monitor. Just default configuration of Protocol with “RAW” and Raw Settings Port Number with “9100” Click “OK” to continue. You will be prompted to select your printer. Enter a printer name and print a test page to ensure successful printer setup.
Page 32
4. Apple OS From desktop, enter “System Preferences” and open “Print & Fax”. Add new printer by clicking “+”. Select Default and locate the print server by Bonjour, then select the correct driver of the printer. Port Used for Print Server: 9100 TCP...
WebDAVclient application is required to work with the CiragoLink.com remote service. In order for you to access remotely, you need to activate your NUS2000 and configure it as a WebDAV server. Please follow the instruction below.
Page 34
Go back to your NUS2000’s admin page (Default: http://nus2000:1010) and from the menu on the left, click on Setup >CiragoLink *** IMPRORTANT: Make sure to change your admin password before activate the NUS as your storage will be exposed to Internet.
Page 35
Remotely Accessing your Attached Storage Devices You can access the NUS2000 remotely using the below steps. Please note that you should only use remote access when you are not on your local network. When you are on your local...
Page 36
Setup Remote Access for WinXP Go to My Network Places, or you can find it from Start Menu. Select “Add a network place” form the left, or under Tools Menu, select Map Network Drive, and click on “Sign up for online storage or connect to a network server”...
Page 37
An authentication dialog will appear. You may enter any user name and password that has been registered in NUS2000 setting. (Note: This authentication is case sensitive.) You can also name the network place when needed. When connected, an icon will be appeared in My Network Places.
Page 38
Until the right box appears, enter the url path information: Local LAN: http://nus2000:9880 Remote Access: http://nus..ciragolink.com:9880 The wizard will ask for authentication to confirm your setup. Then the wizard will ask you to complete with an alias for the new network drive as shown below.
Page 39
Mac OSX built-in software: Mac OSX computer is able to connect to WebDAV server without installing the client application: Enter the URL of http://nus2000.local:9880 for local LAN access And URL of http://nus**********.ciragolink.com:9880 for remote access Then enter the User name and the password to get access to the NUS box And the disk is connected and ready to use.
Page 40
iPhone / iPad You need to install the app before you can use the WebDAV to communicate with the NUS, There are popular app that has the build-in support of the WebDAV such as Numbers, Keynotes & Pages from Apple Inc ...
USB LED off. Web Interface Remember to add the “:1010” after the name or IP address of the NUS2000 to enter the web interface. The default port 80 is reserved for the WebDAV server access.
Page 42
Assign an existing directory destination to save your BT downloads. Make sure the drive is not removed from NUS2000 before the download is complete. You can only have 5 torrent files on the list. Remember to remove the torrent file from the list.
Specifications Hardware Power 100 – 240 AC input, 5V, 3A DC output Typical 4W (not counting USB loads) Weight 4.4 oz / 125 gm Network 10 /100/1000 Gigabit Ethernet USB Ports 4 USB 2.0 host ports (type A connector) USB Storage Maximum capacity of 2 TB hard drive per USB port LED Indicator Power, LAN (Link &...
10. Contact Us Please call or email us if you are having any trouble with the Cirago NUS2000. Cirago International Ltd. 611 Vaqueros Ave, Sunnyvale, CA 94085 Ph: 408-331-8822 Fax: 408-331-8830 Email: support@cirago.com www.cirago.com...
Need help?
Do you have a question about the CiragoLink+ NUS2000 and is the answer not in the manual?
Questions and answers