Related Manuals for Miranda NTW-VD3232
Summary of Contents for Miranda NTW-VD3232
-
Page 1: User Manual
Revision: 0 USER MANUAL NTW-VD3232 Network Routing Switcher Series DIGITAL VIDEO ROUTER - 32x32 Technical specifications are subject to be changed without notice... -
Page 2: Table Of Contents
Revision: 0 Index Revision history General 1.1. Specifications 1.2. Connection drawing Power connection Connecting the NTW-VD3232 to your PC 3.1. Selection of router address 3.2. Pin-out of RS-232 connector 3.3. Maximum cable length MIDI connection 4.1. Several routers in one system 4.2. -
Page 3: Revision History
Revision: 0 0. Revision history Current revision of this document is the uppermost in the table below. Revision Replaces Date Change Description 10/10/00 Initial Revision Technical specifications are subject to be changed without notice... -
Page 4: General
1. General The NTW-VD3232 is a 32x32 serial digital video router with vertical interval switching. This state of the art router provides maximum quality with a data rate of up to 540 Mbit/s and automatic cable equalising on all inputs. High performance circuits in SMD technology assure undiminished signal quality. -
Page 5: Connection Drawing
Connect the DB9 female connector from the desktop power supply to the main unit. Tighten the screws to assure a proper contact. To connect mains to the desk top power supply you need a mains cord with IEC 320 connector. NTW-VD3232 uses the desk top power model AC-10-87-30-005 (±5V / 30W). -
Page 6: Maximum Cable Length
Panels can also be connected to a router via the RS- 232 interface. Please refer to your control panel manual for installation. Attention: Only NTW-32-Pro panels can be used together with NTW-VD3232 when connecting via RS-232. Technical specifications are subject to be changed without notice... -
Page 7: Pin-Out And Cable Type
Revision: 0 4.3. Pin-out and cable type The pin-out of all Network MIDI ports follows the standard MIDI specification. A 1 to 1 cable with 5pin DIN connector is used. The following pin-out is used: 1 - n.c. 1 - n.c. 2 - shield # # # # # # # # # # # # # # # # # # # # # # 2 - shield 3 - n.c. -
Page 8: Router Mode
Revision: 0 Switch Address 5.2. Router mode The NTW-VD3232 router allows switching in different modes. You can choose among: 32x32 Serial Digital Video 1 layer 16x16 Serial Digital Video 2 layer 10x10 Serial Digital Video 3 layer Serial Digital Video 4 layer Switch 5 - 6 on the configuration switch SW A set the router’s mode. - Page 9 Revision: 0 Serial Digital Video 1 layer SDV Signal Input SDV Signal Output Technical specifications are subject to be changed without notice...
- Page 10 Revision: 0 Serial Digital Video 2 layer SDV layer 1 Input SDV layer 1 Output SDV layer 2 Input SDV layer 2 Output Technical specifications are subject to be changed without notice...
- Page 11 Revision: 0 Serial Digital Video 3 layer SDV layer 1 Input SDV layer 1 Output SDV layer 2 Input SDV layer 2 Output SDV layer 3 Input SDV layer 3 Output Technical specifications are subject to be changed without notice...
- Page 12 Revision: 0 Serial Digital Video 4 layer SDV layer 1 Input SDV layer 1 Output SDV layer 2 Input SDV layer 2 Output SDV layer 3 Input SDV layer 3 Output SDV layer 4 Input SDV layer 4 Output Technical specifications are subject to be changed without notice...
-
Page 13: Vertical Interval Trigger
Default is VIT enabled. 5.4. Power up mode Switch 8 on the configuration switch SW A defines the power up mode. The NTW-VD3232 router provides two modes for powering up the system. Mode 1 switches all outputs to input 1. -
Page 14: Connecting Video Signals To The Ntw-Vd3232
Revision: 0 6. Connecting video signals to the NTW-VD3232 The NTW-VD3232 router offers standard 75 ohms BNC connectors for digital video in- and outputs. All digital video inputs are terminated with 75 ohms. 7. Control and connection of Network systems, interface protocol 7.1. -
Page 15: Rs232
RS232 The RS-232 port is used for external control of Network units. The RS-232 port allows the customer to control the equipment via Miranda's i-Control PC program or self-defined customized solutions. Connector for the RS-232 port is a DS9 female. -
Page 16: Video Crosspoint Set
Revision: 0 7.5.2. Video crosspoint set Only for use with Video routers. Command for setting of crosspoints: 1010nnnn 0kkkkkkk 0vvvvvvv - nnnn is the matrix address from 0 up to 15. - kkk kkkk is the output which shall be controlled. kkk kkkk = output number 0 = output 1 127 = output 128... -
Page 17: General Environmental Requirements For Network Electronics Equipment
Revision: 0 General Environmental Requirements for Network Electronics Equipment 1. The equipment will meet the guaranteed performance specification under the following environmental conditions: • Operating room temperature range 0°C to 45°C Except of digital video routers 0°C to 40°C • Operating relative humidity range up to 90% (non-condensing) 2. - Page 18 Revision: 0 Network Electronics AS Hinderveien 4, 3204 Sandefjord, Norway Tel.: +47 33 48 99 99 Fax: +47 33 48 99 98 e-mail: support@networkgroup.no Declaration of Conformity with CE This apparatus meets the requirements of EN 55103-1 (November 1996) with regard to emissions, and EN 55103-2 (November 1996) with regard to immunity;...
Need help?
Do you have a question about the NTW-VD3232 and is the answer not in the manual?
Questions and answers