Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Product Description
Advertisement
Table of Contents
Related Manuals for Telit Wireless Solutions GG863-SR
Summary of Contents for Telit Wireless Solutions GG863-SR
- Page 1 GG863-SR Gateway Hardware User Guide 1vv0300835 Rev.0 - 20/07/09...
- Page 2 GG863-SR Hardware User Guide 1vv0300835 Rev.0 - 20/07/09 DISCLAIMER The information contained in this document is the proprietary information of Telit Communications S.p.A. and its affiliates (“TELIT”). The contents are confidential and any disclosure to persons other than the officers, employees, agents or subcontractors of the owner or licensee of this document, without the prior written consent of Telit, is strictly prohibited.
- Page 3 Applicable Products Product GG863-SR ZigBee GG863-SR Plus GG863-SR Pro For further information on how to order GG863-SR specific model, please contact your Telit representative Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 3 of 22...
-
Page 4: Table Of Contents
3.1 Power Connector........................9 3.2 Supply voltage ........................9 3.2.1 Battery source..........................10 3.3 Switching the GG863-SR Gateway ON and OFF..............10 3.3.1 Switching ON ..........................10 3.3.2 Switching OFF ..........................10 Antenna...........................11 ... - Page 5 GG863-SR Hardware User Guide 1vv0300835 Rev.0 - 20/07/09 9.1 Where to install the gateway ....................19 9.2 How to install the gateway....................19 9.2.1 Power supply ..........................19 9.2.2 Securing the gateway ........................20 9.3 Disposal of this product in the European Union ...............20 ...
-
Page 6: Introduction
(SL) Integracija GG863-SR v uporabniški aplikaciji bo morala upoštevati projektna navodila, opisana v tem piročniku. (SP) La utilización del GG863-SR debe ser conforme a los usos para los cuales ha sido deseñado descritos en este manual del usuario. (FR) L’intégration du GG863-SR dans l’application de l’utilisateur sera faite selon les règles de conception décri tes dans ce manuel. -
Page 7: Audience
Tip or Information – Provides advice and suggestions that may be useful when integrating the module. Related documents [1] 80322ST10058a GG863-Product Description [2] 1vv0300836 GG863-SR Software User Guide [3] 80000NT10006a Telit Battery Charger application note Document History Revision Date... -
Page 8: Physical Characteristics
107 mm (including fixtures) • Width: 64 mm • Thickness: 33 mm Figure 1 - GG863-SR layout and dimensions Weight The weight of GG863-SR is 150 grams. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 8 of 22... -
Page 9: Installation Guidelines
GG863-SR Hardware User Guide 1vv0300835 Rev.0 - 20/07/09 3 Installation guidelines GG863-SR can be fixed on a suitable surface by two screws through the holes (3.3 / 5.8 mm diam.) in the lids forming part of the front and rear panels. Figure 1 shows the maximum and minimum inter-axis distance between the fixing holes. -
Page 10: Battery Source
The battery capacity should be dimensioned on the customer’s application and battery life requirements. Please, refer to [3] for further information regarding type and battery usage. 3.3 Switching the GG863-SR Gateway ON and OFF 3.3.1 Switching ON GG863-SR Gateway switches on automatically each time the Power Supply is connected the first time or re-connected. -
Page 11: Antenna
4 Antenna 4.1 Antenna Output Warning – BEFORE connecting the GG863-SR to a Power Supply source, suitable Antennas shall be connected and properly installed. The antenna has to be installed with care in order to avoid any interference with other electronic devices and has to guarantee a minimum distance from the body (20 cm). -
Page 12: Short Range Antenna Requirements
Table 2 - GSM Antenna requirements 4.4 Short range Antenna Requirements The short range antenna for GG863-SR device shall fulfill the following requirements, depending on the short range technology mounted on the GG863-SR. Zigbee ANTENNA REQUIREMENTS Frequency range 2.4GHz Bandwidth 2.30 –... -
Page 13: Rj11 Connector
GG863-SR Hardware User Guide 1vv0300835 Rev.0 - 20/07/09 5 RJ11 connector The RJ11 connector type is used to provide General purpose I/Os and UART debug interface. All General Purpose input / output lines on the RJ11 GPIO are connected to the Telit GE863-PRO module over a 100 Ohms series resistor. - Page 14 GG863-SR Hardware User Guide 1vv0300835 Rev.0 - 20/07/09 Level Input high level 1.6V 3.3V Input low level 0.4V Output high level 1,65V 2.2V Output low level 0.35V Table 6: Operating Range - Interface levels (CMOS 1.8V) The logic levels of the debug signals are:...
-
Page 15: Mini Usb Type Connector
GG863-SR Hardware User Guide 1vv0300835 Rev.0 - 20/07/09 6 Mini USB type connector Pin-out of mini USB connector is shown in the following table: Signal USBCNX Table 8 - Mini USB Pin out Figure 2 – Mini USB Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved... -
Page 16: Led Indicators
GG863-SR Hardware User Guide 1vv0300835 Rev.0 - 20/07/09 7 Led indicators GG863-SR has two double led indicators, one pair for the GSM technology and one pair for the ZB/RF technology. 7.1.1 GSM Led indicators The green Power LED indicates whether the GSM Engine is powered: if permanently ON, the GSM is powered, if OFF, the GSM is not powered. -
Page 17: Safety And Product Care
• Do not connect any incompatible component or product to the GG863-SR. 8.2 SIM card precautions Before handling the SIM card in your application, ensure that you are not charged with static electricity. -
Page 18: Antenna Precautions
GG863-SR Hardware User Guide 1vv0300835 Rev.0 - 20/07/09 8.3 Antenna precautions If the antenna is to be mounted outside, consider the risk of lightning. Follow the instructions provided by the antenna manufacturer. • Never connect more than one device to a single antenna. The device can be damaged by radio frequency energy from the transmitter of another transmitting device. -
Page 19: Installation Of The Gateway
Connections of components to GG863-SR: The integrator is responsible for the final integrated system. Incorrectly designed or installed external components may cause radiation limits to be exceeded. -
Page 20: Securing The Gateway
GG863-SR Hardware User Guide 1vv0300835 Rev.0 - 20/07/09 9.2.2 Securing the gateway Before securing the gateway take into account the amount of additional space required for the mating connectors and cables that will be used in the application. • Where access is restricted, it may be easier to connect all the cables to the gateway prior to securing it in the application. - Page 21 GG863-SR Hardware User Guide 1vv0300835 Rev.0 - 20/07/09 − The symbol of the crossed-out wheeled bin reproduced on the product or on the packaging, indicates that the product, at the end of life cycle, must be gathered separately from the other waste.
-
Page 22: Conformity Assessment Issues
GG863-SR Hardware User Guide 1vv0300835 Rev.0 - 20/07/09 10 Conformity Assessment Issues GG863-SR is assessed to be conforming to the R&TTE Directive as stand-alone products, so If GG863-SR is installed in conformance with Telit installation instructions require no further evaluation under Article 3.2 of the R&TTE Directive and do not require further involvement of a R&TTE Directive Notified Body for the final product.
Need help?
Do you have a question about the GG863-SR and is the answer not in the manual?
Questions and answers