Casio 2621 User Manual

MA0302-A
About This Manual
(Light)
General Guide
∑ Press C to change from mode to mode.
∑ In any mode, press L to illuminate the display.
Timekeeping Mode
Timekeeping
Use the Timekeeping Mode to set and view the current time and date.
∑ Pressing D in the Timekeeping Mode cycles through available screen formats as
shown below.
Day of the Week Screen
PM indicator
Hour : Minutes
Day of week Seconds
Read This Before You Set the Time and Date !
The times displayed in the Timekeeping Mode and World Time Mode are linked.
Because of this, make sure you select a city code for your Home City (the city where
you normally use the watch) before you set the time and date.
To set the time and date
Seconds
Day
3. When the setting you want to change is flashing, use D and B to change it as
described below.
Screen To do this:
56 Reset the seconds to
Toggle between Daylight Saving Time (
OFF
and Standard Time (
Change the city code
TYO
Change the hour or minutes
P 10:58
Toggle between 12-hour (
12H
24-hour (
2002 Change the year
Change the month or day
6-30
∑ For full information on city codes, see the "City Code Table".
∑ See "Daylight Saving Time (DST)" for details about DST setting.
4. Press A to exit the setting screen.
∑ With the 12-hour format, the P (PM) indicator appears on the display for times in the
range of noon to 11:59 p.m. and the A (AM) indicator appears for times in the range
of midnight to 11:59 a.m.
∑ With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
any indicator.
∑ The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all modes.
∑ The day of the week is automatically displayed in accordance with the date (year,
month, and day) settings.
Daylight Saving Time (DST)
Daylight Saving Time (summer time) advances the time setting by one hour from Standard
Time. Remember that not all countries or even local areas use Daylight Saving Time.
To toggle the Timekeeping Mode time between DST and Standard Time
DST indicator
USER'S GUIDE 2621
∑ Button operations are indicated using the letters shown
in the illustration.
∑ Each section of this manual provides you with the
information you need to perform operations in each
mode. Further details and technical information can be
found in the "Reference" section.
e-DATA MEMORY Mode World Time Mode
Press
C.
Month – Day Screen World Time Screen
Press
D.
World Time Mode time
Month – Day
(Hour: Minutes)
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
2. Press C to move the flashing in the sequence shown
below to select other settings.
DST City Code Hour
12/24-Hour
Month Year
Format
Do this:
Press D.
00
) Press D.
ON
)
OFF
Use D (east) and B (west).
Use D (+) and B (–).
) and Press D.
12H
24H ) timekeeping
Use D (+) and B (–).
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
2. Press C to display the DST setting screen.
3. Press D to toggle between Daylight Saving Time (
and Standard Time ( OFF ).
4. Press A to exit the setting screen.
∑ The DST indicator appears on the display to indicate
that Daylight Saving Time is turned on.
City Temperature Mode
e-DATA MEMORY
Record number
(Page number)
Text
To create a new e-DATA MEMORY record
Remaining memory (%)
4. Press A to store your data and return to the e-DATA MEMORY record screen
(without the cursor).
Minutes
∑ Pressing A causes the message
is stored. After that, the e-DATA MEMORY record screen appears.
∑ The text can show only three characters at a time, so longer text scrolls continuously
from right to left. The last character is indicated by the symbol
stop and restart scrolling.
∑ Records are stored in memory in the sequence they are created.
To recall e-DATA MEMORY records
In the e-DATA MEMORY Mode, use D (+) and B (–) to cycle through e-DATA
MEMORY records as shown below.
Record 1
(
Remaining Memory Screen
To edit an e-DATA MEMORY record
1. In the e-DATA MEMORY Mode, use D (+) and B (–) to display the record you
want to edit.
2. Hold down A until the flashing cursor appears on the display.
3. Use C to move the flashing to the character you want to change.
4. Use D (+) and B (–) to change the character.
5. After making the changes you want, press A to store them and return to the
e-DATA MEMORY record screen.
To delete an e-DATA MEMORY record
1. In the e-DATA MEMORY Mode, use D (+) and B (–) to display the record you
want to delete.
2. Hold down A until the flashing cursor appears on the display.
3. Press B and D at the same time to delete the record.
∑ The message
CLR
record is deleted, the cursor appears on the display, ready for input.
)
ON
4. Input data or press A to return to the remaining memory screen.
Countdown Timer Mode
Alarm Mode
You can use the watch's e-DATA MEMORY to store e-mail
addresses, Web page URLs, and other text data.
∑ All of the operations in this section are performed in the
e-DATA MEMORY Mode, which you enter by pressing
C.
e-DATA MEMORY Management
e-DATA MEMORY can hold up to 315 characters total,
while each record can contain up to 63 characters. The
maximum number of records depends on the number of
characters per record, as shown below.
∑ 63 characters per record: 5 records
∑ 7 or fewer characters per record: 40 records
1. In the e-DATA MEMORY Mode, press D and B at the
same time to display the remaining memory screen.
∑ If
0 % is shown for remaining memory, it means that
memory is full. To store another record, you will first
have to delete some of the records stored in memory.
2. Hold down A until the flashing cursor (
the display, which indicates the setting screen.
∑ The setting screen also shows the record number that
is automatically assigned to the new record.
3. Input the text you want.
∑ When inputting the text, use D (+) and B (–) to
cycle through characters at the current cursor
location, and C to move the cursor to the right. See
"Inputting Text".
SET to appear for about two seconds as the data
s
Press .
Remaining
Record 2
memory
) ( )
screen
Press .
∑ The value on the remaining memory screen is the
percentage of memory that is still available. It does not
indicate the number of records that can be stored.
appears to indicate that the record is being deleted. After the
Stopwatch Mode
) appears on
#
after it. Press A to
1