Advertisement
P L E A S E R E A D A N D S AV E T H E S E
I M P O RTA N T S A F E T Y I N S T R U C T I O N S
When using electrical appliances, basic safety precautions
15. Do not operate fan until fully assembled with all
should always be taken including the following:
parts properly in place.
16. This product is intended for household use ONLY and
1. Read all instructions before using this appliance.
not for commercial or industrial applications.
2. Use fan only for purposes described in the instruction
17. WARNING: To reduce the risk of fire or electric
manual.
shock, do not use this fan with any solid-state speed
3. To protect against electrical shock do not immerse unit,
control device.
plug or cord in water or spray with liquids. Plug the
appliance directly into a 120V AC electrical outlet.
PLEASE READ AND SAVE
4. Close supervision is necessary when any appliance is
used by or near children.
THESE IMPORTANT
5. Unplug from outlet when not in use, when moving
fan from one location to another, before putting on
SAFETY INSTRUCTIONS
or taking off parts and before cleaning.
6. Avoid contact with moving parts.
7. Do not operate in the presence of explosive and/or
flammable fumes.
8. To avoid fire hazard, NEVER place the cord under
rugs or any parts near an open flame, cooking or
other heating appliance.
9. Do not operate any appliance with a damaged cord
or plug after the appliance malfunctions, or has been
dropped/damaged in any manner. Discard fan or
return to an authorized service facility for
examination and/or repair.
10. The use of attachments not recommended or sold by
the appliance manufacturer may cause hazards.
11. Do not use outdoors.
12. Do not let the cord hang over the edge of a table,
counter or come in contact with hot surfaces or leave
exposed to high traffic areas.
13. To disconnect, grip plug and pull from wall outlet.
Never yank on cord.
14. Always use on a dry, level surface.
THIS APPLIANCE HAS A POLARIZED PLUG (one blade is wider than the
other). To reduce the risk of electric shock, this plug is intended to fit in
a polarized outlet only one way. If the plug does not fit fully in the
outlet, reverse the plug. If it still does not fit, contact a qualified
electrician to install the proper outlet.
DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS
SAFETY FEATURE IN ANY WAY.
BORGW2100R_09EM1.indd 2
BORGW2100R_09EM1.indd 2
F E AT U R E S - O P E R AT I O N S
INSTALLATION INSTRUCTIONS
WARNING: BE SURE FAN IS SECURELY INSTALLED IN
YOUR WINDOW AT ALL TIMES. DO NOT LEAN OR PUSH
Carefully unpack contents from carton.
ON FAN WHILE IT IS IN THE WINDOW.
Figure 1
Figure 2
E F
C D
B
G
I
G
LEFT
H
Extra Extender Panels 4.25
inches (10cm) - 2 pieces
included in your box
A
J
I
K
OPERATING INSTRUCTIONS
A. Front Grill
H. Built-in Extender
1. Plug cord into any standard 120 volt AC outlet.
B. Control Panel
Screen
C. Mode Button
I. Extender Locks (2)
2. To turn the fan on and control the speed, press the
mode button. Note that pressing the mode button will
D. LED Display
J. Extender Panels
allow you to cycle through the speed setting (High=3,
E. Temp Up (+)
(2) (not shown)
F. Temp Down (-)
K. Remote Control
Med=2, Low=1) as well as the Automatic Thermostat
G. Fan Directional
Temperature settings (Auto High = A3, Auto Medium =
A2, Auto Low = A1). 0 indicates the Off position.
Switches (2)
3. Set the airflow direction by sliding the fan directional
switches located above each fan blade. Note that the
FOR DOUBLE-HUNG AND SLIDER
fan blades work independently from one another
WINDOWS
and can be used for air intake (bring fresh air in
1. Set the fan into your window opening (note that the
from outside), exhaust (push air out from within the
window screen does not have to be removed or left open.)
room) or exchange (cycles air in and out of the room
simultaneously).
2. If the fan does not fit snugly to the top and bottom of
the window casing, attach the Extender Panel(s) and
adjust the built in extender screen until the fan fits
AUTO MODE
safely in your window. (See Figure 2)
Your fan is equipped with a Programmable Digital
3. To keep the fan in place, carefully close the window
Thermostat that will automatically turn the fan ON and
so that the bottom edge of the window rests on the
OFF depending upon the preset comfort temperature.
flat surface on top of the fan.
This is ideal for night time operation when temperatures
NOTE: FOR SLIDER WINDOWS, SET THE FAN VERTICALLY
can drop below comfort levels.
IN YOUR WINDOW OPENING WITH THE LEFT SIDE OF THE
For example, if you set your fan to 75 degrees and the
FAN SITUATED ON THE BOTTOM AND THE BUILT-IN
temperature drops to 74 degrees, the fan will
EXTENDER SCREEN FACING UPWARDS.
F E AT U R E S - O P E R AT I O N S
automatically turn off. The fan will automatically turn on
again when the room temperature exceeds the set
temperature.
SETTING AUTO MODE
FRONT VIEW
1. Press the Mode button to scroll to the desired auto
RIGHT
speed setting (A3, A2, or A1).
2. Choose the desired temperature setting by pressing
Built-in Extender, pull
the Temp Up (+) or Temp Down (-) buttons. You may
out up to 7 inches
select a temperature between 60 and 80 degrees
(17cm)
Fahrenheit. Once the desired temperature is set, the
digital display will return to show the ambient room
temperature. View the set temperature by pressing
either the Temp Up (+) or Temp Down (-) buttons.
IMPORTANT: If the fan does not start in the Auto
mode, please be sure that the set temperature is below
the current room temperature. Lower the set temperature
UNIT'S LENGTH
if you would like the fan to start or switch over to the
manual speed modes.
SETTING THE TIMER
1. Hold both the Temp Up (+) and Temp Down (-)
buttons down until the digital display flashes "00".
2. Press the (+) or (-) buttons to change time in 1 hour
increments. Note selection ranges from 1 to 16
hours. When in the timer mode, the time remaining
will be displayed.
NOTE: If Timer is set when fan is ON, the time displayed
will turn the fan OFF once elapsed. If Timer is set when
fan is OFF, the time displayed will turn the fan ON. (The
default ON speed setting is Manual Low).
NOTE: Timer function can be turned off by pressing the
MODE key at any time.
REMOTE CONTROL
This unit includes two (2) AAA batteries, 1.5V.
Battery Replacement
a) Locate the battery cover on the back of the remote
control handset. Slide the battery cover off with your
thumb.
b) Remove old batteries.
c) Insert two new batteries, pressing them firmly into
their slot.
d) Replace the battery cover.
NOTES:
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc), or
rechargeable (nickel-cadmium) batteries.
• Replace all batteries of a set at the same time.
• Clean the battery contacts and the devices' contacts
prior to installing the batteries.
• Remove the batteries from the equipment when it is
not being used for an extended period of time.
• Remove the used batteries promptly.
FCC STATEMENT
Potential for Radio/Television interference
This product has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15
of the FCC rules.
These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. The product generates, uses, and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that the interference will not occur in a
particular installation. If the product does cause harmful
interference to radio or television reception, which can be
determined by turning the product on or off, the user is
encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the product and the
receiver.
• Connect the product into an outlet on a circuit
different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV
technician for help.
Changes or modifications not expressly approved by the
party responsible for compliance could void the user's
authority to operate the equipment.
11/17/09 11:07:06 AM
11/17/09 11:07:06 AM
Advertisement
