Lucent Technologies Telephone Paging Amplifier Installation And Use Manual
Lucent Technologies Telephone Paging Amplifier Installation And Use Manual

Lucent Technologies Telephone Paging Amplifier Installation And Use Manual

250-watt telephone paging amplifier

Advertisement

Telephone Paging Amplifier
250-Watt Model
Installation and Use Manual
Issue 2, January 2000
© 1999 Bogen Communications, Inc.
All rights reserved. 54-2023-01 9910
LU250WAMP: PEC Code: 5328-250
COM Code: 408186096
Select Code: 701-000-116

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Telephone Paging Amplifier and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Lucent Technologies Telephone Paging Amplifier

  • Page 1 Telephone Paging Amplifier 250-Watt Model Installation and Use Manual Issue 2, January 2000 © 1999 Bogen Communications, Inc. All rights reserved. 54-2023-01 9910 LU250WAMP: PEC Code: 5328-250 COM Code: 408186096 Select Code: 701-000-116...
  • Page 2 © 1999 Bogen Communications, Inc. All Rights Reserved. Printed in Korea. Notice Every effort was made to ensure that the information in this guide was complete and accurate at the time of printing. However, information is subject to change. Important Safety Information Always follow these basic safety precautions when installing and using the unit: 1.
  • Page 3: Table Of Contents

    Contents Page INTRODUCTION ..........................4 PACKAGE CONTENTS......................4 INSTALLATION..........................5 Mounting ..........................5 Wall Mounting........................5 Rack Mounting ........................5 WIRING CONNECTIONS ......................6 Input Wiring........................6 Tel Input and Control Pair ....................6 TEL Input to Universal Coupler....................7 Music Input ..........................7 Microphone Input ........................7 Night Ringer Connections ....................8 Bridging Inputs ........................8 Input Cover Replacement ....................8 ‘...
  • Page 4: Introduction

    25V COM GND Figure 1: Telephone Paging Amplifier Introduction This document describes the Lucent 250-watt Telephone Paging Amplifier.These are full-featured, wall-mounted amplifier that provides inputs for dry loop 600-ohm telephone page signal, background music source, and low impedance microphone. A set of control inputs allow an external contact closure to mute background music and open the telephone page channel.
  • Page 5: Installation

    Figure 2: Wall Mounting the Amplifier SCREW #8 x 5/8" (M4 x 16 mm) WITH TEFRON WASHER 1/8 x 5/16 (3 x 8 MM) TYP 4 PCS RACK MOUNTING SCREWS ARE NOT SUPPLIED Figure 3: Rack Mounting the Amplifier Installation Mounting The amplifier is designed for wall mount applications but can also be mounted in a standard 19"...
  • Page 6: Wiring Connections

    Tel page channel (see Figure 4). NOTE: In instances where the amplifier is to be placed permanently in the Tel page mode, a wire jumper must be installed between the TEL and COM terminals. Telephone Paging Amplifier Figure 4: Wiring for TEL Input MIC VOLUME...
  • Page 7: Tel Input To Universal Coupler

    22 AWG shielded, twisted pair speaker cable (Com Code: 401882956, PEC Code: 2734-SPK) will also work. When extending microphone cable, be sure to connect the shields of the microphone cable to the extension wire. Figure 5: Connect Microphone to Telephone Paging Amplifier MIC VOLUME TEL VOLUME...
  • Page 8: Night Ringer Connections

    Input Cover Replacement When all connections are made, remove an appropriate knockout on the input cover. Replace the cover and tighten the screws while dressing the wires through the knockout hole. TEL VOLUME LUCENT TECHNOLOGIES POWER PEAK LEVEL APHEX BRIDGING...
  • Page 9: Output Wiring

    Output Wiring All output wiring connections are made to the terminal strip located under the right side access panel. Loosen the 2 Phillips-head screws on each side of the cover and remove the cover. IMPORTANT: Before making any connections or wiring changes to the amplifier or any equipment connected to the amplifier, make sure that the amplifier is NOT plugged into an AC outlet.
  • Page 10: Luwmt1A Connector

    Figure 8 : LUWMT1A Connection to RCA Jack on Amplifier RCA Jack LUWMT1A Amplifier LUWMT1A Connector An RCA jack is provided near the output terminal strip for connection to an LUWMT1A impedance matching transformer (Com Code 405891680). A 600-ohm, telephone level output signal can be obtained by plugging the RCA connector of the LUWMT1A into this jack and taking the output signal off of the LUWMT1A screw terminals (see Figure 8).
  • Page 11: Operation

    Operation IMPORTANT: Before plugging the amplifier into an AC outlet, turn all volume controls to their full counterclockwise positions and all other controls to their reference position or to mid rotation. Indicators POWER IND The POWER IND LED illuminates whenever AC power is applied to the amplifier (there is no power switch on the amplifier).
  • Page 12 MUSIC VOLUME This control adjusts the level of the background music output. No reference level setting position is provided. The background music level should be set to an acceptable level without overdriving the system. When adjusting this level, the PEAK LEVEL indicator should be observed to ensure that the amplifier signal is not distorted.

This manual is also suitable for:

Lu250wamp

Table of Contents