1. Manuals
  2. Brands
  3. Envirco Manuals
  4. Control Unit
  5. CC1-10
  6. Operation manual

Envirco CC1-10 Operation Manual

Envirco control console operation manual
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
www.envirco.com
ENVIRCO
Control Console
Models: CC1-10 (Part No. 63971-001)
Control Console Operation Manual Rev 0400809.doc
CC1-25 (Part No. 63971-002)
CC1-50 (Part No. 63971-003)
Operation Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CC1-10 and is the answer not in the manual?

Questions and answers

Related Manuals for Envirco CC1-10

Summary of Contents for Envirco CC1-10

  • Page 1 ENVIRCO Control Console Models: CC1-10 (Part No. 63971-001) CC1-25 (Part No. 63971-002) CC1-50 (Part No. 63971-003) Operation Manual Control Console Operation Manual Rev 0400809.doc...

  • Page 2: Table Of Contents

    ENVIRCO Control Console Operation Manual TABLE OF CONTENTS TITLE PAGE 1.0. SAFETY PRECAUTIONS ..........................3 2.0. OVERVIEW ..............................4 2.1......................4 ONTROL ONSOLE ODELS 2.2..........................4 UNCTIONS 2.3............................4 EATURES 2.4............................4 ENEFITS 3.0. SPECIFICATIONS............................5 3.1.

  • Page 3: Safety Precautions

    • Service to the Control Console cannot be performed in the field. Returned equipment still under warranty to Envirco. • Before trying to remove the Control Console from the clean system it controls, switch power off for the entire clean system at service panel and lock service panel to prevent power from being switched on accidentally, and follow proper procedures as necessary.

  • Page 4: Overview

    The versatile design allows control of an array of MAC 10 XL installed Envirco Phase Controllers or “Smart” MAC 10 units linked to an Envirco DC Controller. The console combines a user interface with MODBUS master capability so no additional networking components are needed and no MODBUS knowledge is necessary to install a network.

  • Page 5: Specifications

    ENVIRCO Control Console Operation Manual 3.0. Specifications 3.1. Electrical Specifications Supply Voltage: 6-12 Vdc Typical Supply Current: 90 mA Network Transceivers: 2-wire, 1/8 unit load type Operating Temperature: 0-40° Celsius (32-104°F) DC Power Connector: 2.1 mm DC power jack MODBUS network: RJ45 socket 3.2.

  • Page 6: Installation

    A network is constructed by simply daisy-chaining MAC 10 XL installed Envirco Phase Controllers or “Smart” MAC 10 installed DC Controllers from the Control Console. Specific network wiring information can be found in the Envirco MAC 10 XL Control System or MAC 10 DC Control System operation manuals.

  • Page 7: Control Console Installation Template

    ENVIRCO Control Console Operation Manual 4.2. Control Console Installation Template Page 7...

  • Page 8: Control Console Operation

    Control Console then scans all addresses valid for that model (10, 25 or 50.) If no MAC 10 XL installed Envirco Phase Controllers or “Smart” MAC 10 units linked to an Envirco DC Controller is detected, the Control Console repeats the scan sequence until at least one unit is found.

  • Page 9: Standby Monitor Mode

    ENVIRCO Control Console Operation Manual 5.3. Standby Monitor Mode The Control Console immediately enters standby monitor mode at the conclusion of power-on scanning. The Control Console remains in standby monitor mode until one of the two dials are rotated. If the dials are not adjusted for a period of 30 seconds, the Control Console will revert to standby monitor mode.

  • Page 10: User Monitor Mode

    ENVIRCO Control Console Operation Manual 5.4. User Monitor Mode If any dial activity is detected, the Control Console leaves standby monitor mode and enters user monitor mode. In this mode, any unit can be selected by rotating the Select dial.

  • Page 11: Option Menu

    ENVIRCO Control Console Operation Manual 5.6. Option Menu The option menu allows a user to perform the following functions: A. Change the access level by entering pass-codes (A1…A3) B. Select High Speed (normal) or Low Speed (global set back) C. Adjust the Low Speed set back D.

  • Page 12: Access Levels

    ENVIRCO Control Console Operation Manual 5.6.3. Adjusting Low Speed Set Back (LS) • This action requires access levels A1-A2 • Use the Select dial to display the “LS” menu option • Rotate the Adjust dial to vary the set-back percentage (0-99%) 5.6.4.

  • Page 13: Limited Warranty

    (1) year when operated in clean room conditions. Envirco’s sole obligation under this warranty is to repair or replace any parts of the equipment which are defective for a period of one (1) year from the invoice date, provided that the repair or replacement is actually performed within the one (1) year period from the invoice date.
  • Page 14 5601 Balloon Fiesta Parkway N.E. • Albuquerque • New Mexico • 87113 • USA 505.345.3561 • 800.545.6598 • Fax: 505.345.8875 www.envirco.com...

This manual is also suitable for:

Cc1-25Cc1-50

Table of Contents