Monterey A10-1225 Owner's Manual

Gourmet series
Hide thumbs Also See for A10-1225:

Advertisement

Quick Links

OWNER'S MANUAL
Gourmet Series Marine Gas Grill
Model A10-1225
For questions regarding performance, assembly,
operation, parts, or returns, contact the experts
at MAGMA by calling TOLL FREE IN U.S.A. AND
CANADA 1-800-86-MAGMA
7:00 a.m. - 5:00 p.m. Pacific Time Monday thru
Friday or e-mail us at mail@MagmaProducts.com
Read all instructions before operating. Save manual for future reference.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the A10-1225 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Monterey A10-1225

  • Page 1 Model A10-1225 For questions regarding performance, assembly, operation, parts, or returns, contact the experts at MAGMA by calling TOLL FREE IN U.S.A. AND CANADA 1-800-86-MAGMA 7:00 a.m. - 5:00 p.m. Pacific Time Monday thru Friday or e-mail us at mail@MagmaProducts.com...
  • Page 2: Important Safety Warnings

    • USE PROPANE GAS ONLY. FUEL STORAGE SHOULD BE IN COMPLIANCE WITH THE AMERICAN BOAT AND YACHT COUNCIL (ABYC) STANDARDS A-1 (9), MARINE LIQUIFIED PETROLEUM GAS (LPG) SYSTEMS. • FOR NATURAL GAS APPLICATION CONTACT MAGMA. • ALWAYS LIGHT GRILL WITH LID OPEN. • NEVER LEAVE HOT GRILL UNATTENDED.
  • Page 3 ON-BOARD FUEL SYSTEMS APPLICATION •For on-board LPG (Propane) Systems, use Magma Type 3-High Output- Low Pressure LPG Control Valve and Magma Low Pressure LPG Hose Kit. •For on-board CNG (Natural Gas) Systems, use Magma Type 4-High Output- Low Pressure Natural Gas Control Valve.
  • Page 4: Operating Procedures

    OPERATE ONLY ON “LOW” WHEN LID IS CLOSED. ALWAYS OPERATE WITH GREASE TRAY IN PLACE. WARNING: Do not overheat grill. Magma Grills do not require pre-heating. Stainless Steel loses anti-corrosive characteristics when subjected to extreme heat. Most grilling is done on low temperature with the lid closed. If medium or high heat is required, grill with lid open.
  • Page 5: Disassembly And Reassembly

    ELECTRODE SPARK ADJUSTMENT CAUTION: Spark can cause small shock. Do not leave fingers on or near electrode wire while engaging igniter. • Electrode wire should be approximately 1/8” from gas exit hole in burner. Carefully adjust wire if required. DISASSEMBLY & RE-ASSEMBLY •...
  • Page 6: Maintenance

    Control Valve - All valves are set and tested at our factory. Do not attempt to adjust or disassemble the valve in any way. Call Magma if you suspect it is not adjusted properly. Clean valve with a cloth and remove any debris obstructing the gas outlet orifice using a pin or needle.
  • Page 7: Troubleshooting Guide

    (see page 5) Igniter/electrode wire loose or Reconnect wire between disconnected igniter & electrode (see page 5) Wire is shorted causing spark Call Magma from wire before electrode No spark being generated Call Magma Burner will not No gas flow...
  • Page 8: Limited Warranty

    U.S. Postal Service mail at “Magma Products, Inc., attention Customer Service, 3940 Pixie Ave. Lakewood, CA, 90712.“ The defective part, along with proof of purchase, must be returned postage prepaid to Magma Products, Inc. We suggest that you keep your purchase receipt as we may require reasonable proof of purchase.

This manual is also suitable for:

Newport a10-918

Table of Contents