Related Manuals for Hunter WHISPERWIND2000
Summary of Contents for Hunter WHISPERWIND2000
- Page 1 Y e a r - R o u n d C o m f o r t F o r t h e N e x t G e n e r a t i o n ® Type X 41277-01 05/98...
- Page 2 Where Purchased ______________ All Hunter ceiling fans will provide We at Hunter are proud of our work. _____________________________ comfort and performance in your We appreciate the opportunity to home or office for many years. The...
-
Page 3: Table Of Contents
Step 4 - Wiring the Fan ........................... 11 Step 5 - Hanging the Fan ..........................13 Step 6 - Attaching Blade Assembly ........................14 Step 7 - Attaching Light Fixtures ........................17 Operating Your Hunter Fan ..........................22 Troubleshooting .............................. 23 41277-01 05/98... -
Page 4: Important Information
If you need help installing the fan, let box and associated wall your Hunter fan dealer can direct you switch location. If you can- to a licensed installer or electrician. 41277-01 05/98... -
Page 5: Step 1 - Getting Ready
If any parts are missing or damaged, cluded with each Hunter accessory. manual assume that you have used contact your Hunter dealer or call the the “Guide to Choosing and Prepar- For quiet and optimum performance Hunter Parts Department at 901/ ing a Ceiling Fan Site”... - Page 6 For ceilings higher than 8 ity and ease of installation. The steps feet, you can also purchase Hunter in this manual include specific in- extension rods. All Hunter fans use structions for the fan mounting 34°...
-
Page 7: Step 2 - Installing The Ceiling Plate
® STEP 2 - INSTALLING THE CEILING PLATE 1. Drill two pilot holes into the wood For Angle Mounting Only: Be Isolators support structure through the sure to orient the ceiling plate so outermost holes on the outlet that the two hooks point up to- box. - Page 8 ® 5. Place a flat washer on each of the two 3" screws and pass the screws through the slotted holes in the ceiling plate as shown in Figure 2c. 6. Tighten the screws into the 9/64" pilot holes; do not use lubricants on the screws.
-
Page 9: Step 3 - Assembling The Fan
® STEP 3 - ASSEMBLING THE FAN Follow sub-step 1 below for all fans. in the housing as shown in Fig- 2. Place the large assembly washer Then, use the additional instructions ure 3a. included with the fan over the for the type of mounting you have adapter and canopy as shown in Flush Mounting... - Page 10 ® 4. Attach the canopy tightly to the Standard and Angle Mounting fan assembly with three #8-32 x (For 8-foot Ceilings and Higher) 3/4" assembly screws and #8 1. Fasten the fan housing to the lockwashers as shown in Figure motor hanger adapter with three #8-32 x 3/4"...
-
Page 11: Step 4 - Wiring The Fan
® STEP 4 - WIRING THE FAN 1. Disconnect the power by turning Note: To hang the fan you must 3. You can use either one or two off the circuit breakers to the out- tilt the canopy to an almost verti- wall switches to control the fan let box and associated wall switch cal position so the canopy slots... - Page 12 ® 4. Connect the wires as shown in Figure 4c. To connect the wires, Wall Switch Wire For twist the bare metal leads to- Separate Control of Light Kit (Note: Wall switch must be acceptable gether. Place a wire nut over the as a general-use Black Power...
-
Page 13: Step 5 - Hanging The Fan
® STEP 5 - HANGING THE FAN Sub-steps 1 and 2 apply to Flush, 2. Install and tighten the two #10- Groove in Hanger Ball Standard, and Angle mounting. Sub- 32 x 1/2" mounting screws. step 3 applies to Standard and Angle 3. -
Page 14: Step 6 - Attaching Blade Assembly
(Positioned 32 x 1/2” oval-head Phillips Upside Down) screws as shown in Figure 6a. (Hunter Fans use several types of decorative medallions.) Figure 6a - Attaching Fan Blade to Speed Ring™ Using Decorative Medallion Note: Some blades are reversible, (Speed Ring™ Positioned Upside Down) with two different finishes. - Page 15 ® ATTACHING SPEED RING™ TO CAUTION MOTOR Make sure that all Speed 1. Position three grommets in the Ring™ screws are securely cut-out slots in the Speed Ring™ tightened. Loose screws could as shown in Figure 6b. cause noise, improper fan op- eration, damage to the fan, or possible injury.
- Page 16 5. Replace and tighten the screws you removed in sub-step 2. Note: If you are installing a Speed Hunter light fixture, proceed to 6. Replace the switch housing cap Ring™ “STEP 7 – ATTACHING LIGHT and plug button.
-
Page 17: Step 7 - Attaching Light Fixtures
Hunter-brand light kits, Type A-Z. such as a tag, to the service Cover Hunter light kits are designed, tested, panel. and UL approved for all Hunter fans, Switch • Connect house wiring to Housing and are available at most Hunter the fan before attaching dealers. - Page 18 41277-01 05/98...
- Page 19 ® ATTACHING LIGHT FITTER TO Note: Be sure to push wire connec- Switch FAN SWITCH HOUSING tions up into the switch housing. Housing Switch 2. Insert and tighten two #6-32 x Low-Profile Lights Light Housing 1 1/4" screws. Refer to Figure 7d. Fixture Cover 1.
- Page 20 ® AURORA FIXTURES Refer to Figure 7f. Figure 7f - Aurora Fixtures 41277-01 05/98...
- Page 21 ® LOW-PROFILE FIXTURES Refer to Figure 7g. 1. Install bulbs. 2. Insert globe. 3. Install and tighten thumbscrews manually. Do not overtighten. Thumb- screw Globe Figure 7g - Low-Profile Fixtures 41277-01 05/98...
-
Page 22: Operating Your Hunter Fan
® OPERATING YOUR HUNTER FAN 1. Turn on electrical power to the direct breeze. In winter, having fan. the fan draw air upward (clock- wise blade rotation) will distrib- 2. The pull chain controls power to ute the warmer air trapped at the the fan. -
Page 23: Troubleshooting
® TROUBLESHOOTING PROBLEM PROBABLE CAUSE SOLUTION Nothing happens; fan does not move. 1. Power turned off, fuse blown, or 1. Turn power on, replace fuse, or re- circuit breaker tripped. set breaker. 2. Loose wire connections or wrong 2. Loosen canopy, check all connections connections. - Page 24 If you have tried these troubleshooting solutions and still have trouble, call 901/745-9222 or visit our Web site at http://www.hunterfan.com. Hunter Fan Company 2500 Frisco Avenue Memphis, TN 38114 ®...