Alcatel TEMPORIS 55-CE User Manual

NOTE: If you find any of the parts missing, please contact your
local shop where you buy this product right away.
TELEPHONE JACK REQUIREMENTS
To use this phone, you need a
telephone jack, which might look the
here, installed in your home. If you don't have a jack,
call your local phone company to find out how to get
one installed.
INSTALLATION
CAUTION: Disconnect the phone cord from the wall
outlet before installing or replacing the batteries.
• Never install telephone wiring during lightning storm.
• Never touch un-insulated telephone wires or terminals, unless the
telephone line has been disconnected at the network interface.
• Use caution when installing or modifying telephone lines.
• Never install telephone to operate in wet or damp locations.
TEMPORIS 55-CE
TEMPORIS 55-CE
INSTALLING AND REPLACING THE BATTERIES
Your Caller ID phone uses 3 AA-Size alkaline batteries for receiving
and storing Caller ID records and for storing the numbers you use for
frequently.
IMPORTANT: If you are not going to use the telephone for more
than 30 days, remove the batteries because they may leak and
damage the unit.
BATTERY
1. If the telephone line cord is connected, disconnect it from the base
unit.
2. Carefully turn over the phone, use a pen or paper clip to loosen
the battery cover. Open the battery compartment by pushing on
the battery cover and sliding it away from the unit.
3. Insert 3 AA-size alkaline batteries (not included) as shown on the
diagram in the battery compartment.
4. Snap the battery compartment door
back into place.
5. If the line cord was previously
connected, reattach it to the unit
and check your memory locations.
INSTALLING THE PHONE
Your phone should be placed on a level surface, such as a desk or
table top, or you can mount it on a wall.
1. Connecting the handset.
2. Connecting the telephone
line.
WALL MOUNTING
1. Rotate the wall mounting knob as shown in the following layout:
2. Install the base unit to the wall and then plug one end of line cord
into the junction box and the other end into modular telephone
line jack marked "
3. Fix the telephone in the wall as the following layout.
Alcatel Logo and Alcatel name are trademarks of Alcatel and used under
license by Thomson.
INTRODUCTION OPTIONS MENU
Your Caller ID phone stores and displays specific information,
provided by your local telephone company, to subscribers of Caller
ID or similar caller identification services.
Your Caller ID phone enables you to:
• Identify callers before you answer the phone.
• View the time and date of each incoming call. Month
• Record up to 58 Caller ID name and number messages sequentially.
MAIN FEATURES
• FSK/DTMF auto detect.
• Call Waiting Caller ID(FSK Type Ⅱ).
• Incoming call log records up to 58 calls name and number.
• Outgoing call log records up to 10 last dialed numbers.
• 10 two-touch memories.
• On hook pre-dialing.
Phone
• Redial.
number display
• Pulse or Tone dialing mode.
• Flash timing selectable.
• Mute function.
• Speakerphone.
To get the most from your new phone, you are suggested to take a
few minutes right now to read through this user guide.
SHORT GLOSSARY OF TERMINOLOGY USED IN THIS
MANUAL
Hook switch. The part of the phone that pops up to activate the
phone line when the handset is lifted from the base.
Off-hook. A term used to describe the phone in its active mode when Set button
the handset is off of the base cradle or when the SPEAKER button is Store button
pressed.
Mute button
On-hook. A term used to describe the phone in an inactive mode.
PARTS CHECKLIST
Make sure your package includes the items:
Line cord
DESK
TEMPORIS 55-CE TEMPORIS 55-CE
Speaker Volume button
Base Handset Coil cord User's Guide
T55-CE E and F IB.indd 1
Alcatel Logo and Alcatel name are trademarks of Alcatel and used under
license by Thomson.
SETTING THE PHONE
NOTE: Proceed immediately to change any of the following
factory preset as required.
Wall plate
RJ11C type modular There are 4 options to set:
one pictured
Modular telephone line jack
SETTING DATE/TIME
SETTING LOCAL AREA CODE
SIZE A A
SIZE A A
SIZE A A
Caller ID number received that has area code (front of the number)
matches with the set area code will be filtered.
SETTING LONG DIST CODE
1
Wall mounting knob
This code will be added to the front of the telephone number by press
Location Rotate 180°
and hold button "0". This feature will only work in pre-dialing mode.
SETTING LANGUAGE
WALL MOUNTING: The knob is designed to keep
this unit in place when the telephone is vertical
on the wall.
".
PHONE OPERATION
RECEIVING A PHONE CALL
CASE 1
Answer Call
Ringing
3
CASE 2
Ringing Answer Call
Low battery indicator
Morning
Voice mail
Speakerphone
Afternoon
Call-log CASE 3
Day Repeat New CID
Hour Minutes Mute Mic Number
Ringing Answer Call
M D
CASE 4
Name display Call waiting Ringing
Answer Call
Ring Volume Switch Flash Time Switch
Tone/Pulse Switch
End Call
Display MAKING A PHONE CALL
CASE 1
Dial button
DESK
Delete button Dial number
Contrast button
Flash button
In use indicator
Message indicator
CASE 2
Up/Down buttons
CONTRAST LEVEL ADJUSTMENT
Press the CONTRAST button to adjust the display contrast level.
P=>T DIAL MODE
Redial/pause button
In PULSE dialing mode, press [*] button to access TONE service.
Speaker button
Microphone
REDIAL
CASE 1
OR
The number shown
will be dialed
Date format
CASE 2
OR
Time format
Last number redial
MUTE
In off-hook state, user can press the MUTE button to access mute
function, when MUTE is on, the MUTE indicator will show on the screen.
Press the MUTE button to exit mute function and resume normal
conversation.
SPEAKER VOLUME LEVEL ADJUSTMENT
User may adjust speakerphone loudness level during conversation by
pressing the VOL button.
English/Turkey/French/ RINGER VOLUME LEVEL
Greece/Polish
The phone will ring when there is incoming call. User may select ringer
loudness to HI, MID or LOW. The ringer loudness switch is indicated at
location A.
PULSE TONE SETTING
User may select P (PULSE) or T(TONE) dialing mode according to
requirements from the local telephone company. The T/P switch is
indicated at location B.
Enter Month, Day,
Hour and Minute FLASH TIME SETTING
User may use FLASH feature to access services provided by the
local telephone. The timing of the Flash is dependent on the local
telephone exchange and user may change it by setting the switch
indicated at location C.
Enter your area code
A- Ringer Volume Switch
C B A
B- Tone/Pulse Switch
C- Flash Time Switch
CALLER ID FEATURES
Caller ID (CID) is a service available from your local telephone
company.
For Caller ID to work on this system, you must subscribe to Caller ID
service.
This unit can receive caller ID without any setting. Your caller ID
information may include the phone number, name, date and time.
REVIEWING INCOMING CALLS
Enter your long
distance code
Reviewing Incoming Call Log
DIAL BACK A CALLER ID NUMBER
CASE 1
Select the
The number shown will be dialed
caller number
Select Language
CASE 2
Select the Add number to the
caller number front of number
OR OR
End Call
The number shown will be dialed
NOTE: Use button to truncate number at the front of the
Caller ID number.
REVIEWING OUTGOING NUMBERS
End Call
DIAL BACK AN OUTGOING NUMBER
End Call
The number shown will be dialed
DELETING A CALLER ID NUMBER
Select the number
OR OR
DELETING ALL CALLER ID NUMBER
The number shown will be dialed
OR
Select Caller Press and
Dial number
ID number
hold 3 seconds
MEMORY OPERATIONS
Assigned
key Assigned key
characters
OR characters
1 P Q R S 7
A B C 2 T U V 8
D E F 3 W X Y Z 9
G H I 4
J K L 5
M N O 6
STORING A TELEPHONE NUMBER
Memory Location
Dial Number Input Name
STORING INCOMING CALL NUMBER
Select the number Memory Location
Confirm number store Input Name
STORING OUTGOING NUMBERS INTO MEMORY
Select the number Memory Location
Confirm number store Input Name
CHECK CONTENT OF MEMORY LOCATION
OR OR
Select Memory Location will
display number and name
DIALING A MEMORY LOCATION
CASE 1
Select Memory Location
OR OR
CASE 2
OR
Memory Location
DELETING A MEMORY LOCATION
OR OR
Select Memory Press and hold
Location 3 seconds
TROUBLESHOOTING TIPS
No Dial Tone
• Check all cabling to make sure that all connections are secure and
not damaged
• Check hook switch: Does it fully extend when handset is lifted from
cradle?
No Display
• Replace the batteries.
• Check for proper battery installation.
No Information is Shown After the Phone Rings
• Are you subscribed to Caller ID service from your local telephone
company?
• Be sure to wait until the second ring before answering.
Phone Dials in Pulse with Tone Service
• Make sure T/P DIAL MODE is on "T" mode.
Phone Won't Dial Out with Pulse Service
• Make sure T/P DIAL MODE is on "P" mode.
Phone Does Not Ring
• You may have too many extension phones on your line. Try
unplugging some extension phones.
• Check for dial tone. See troubleshooting tips for no dial tone.
Incoming and Outgoing Voice Volume Low
• Are other phones off hook at same time? If so, this is normal
condition as volume drops when additional phones are used at
once.
• Check the handset receiver or speaker volume.
GENERAL PRODUCT CARE
To keep your phone working and looking good, follow these
guidelines:
• Avoid putting it near heating appliances and devices that
generate electrical noise (for example. motors or fluorescent
lamps).
• DO NOT expose to direct sunlight or moisture.
• Avoid dropping and other rough treatment to the unit.
• Clean with a soft cloth.
• Never use a strong cleaning agent or abrasive powder because
this will damage the finish.
• Retain the original packaging in case you need to ship it at a later
date.
Used equipment must be disposed of in
compliance with current environment protection
regulations. You should return it to your reseller or
disposes of it in an approved recycling centre.
"WEEE" Weight: 0.60Kg
Model Temporis 55-CE
00030371 (Rev.0 E/F)
09-41
Printed in China
2009-9-11 14:30:27