TABLE OF CONTENTS TABLE OF CONTENTS TABLE OF CONTENTS ..............i DIGITAL TELEVISION TRANSITION NOTICE ......1 ENERGY STAR DISCLAIMER ............. 1 IMPORTANT INFORMATION............2 Warnings .................. 2 NOTICES ................. 3 FCC COMPLIANCE STATEMENT .......... 4 IMPORTANT SAFETY INSTRUCTIONS ......... 5 Circuit Overload................
Page 4
ANTENNA OR COAXIAL CABLE CONNECTION SETUP ..21 CABLE OR SATELLITE BOX CONNECTION SETUP ..24 OTHER INPUT SOURCE CONNECTION SETUP ....26 WESTINGHOUSE HDTV SETUP - NOT THROUGH CABLE/ SATELLITE BOX..............28 BASIC OPERATIONS..............30 TURNING THE POWER ON AND OFF ......... 30 ADJUSTING THE VOLUME...........
Changes to certain features, settings and functions of this TV can change and/or increase its power consumption. Depending on how settings are changed, power consumption may exceed the limits required for ENERGY STAR ® qualification. This Westinghouse TV will operate at optimal energy efficiency in “Home” mode.
IMPORTANT INFORMATION IMPORTANT INFORMATION Warnings To reduce the risk of fire or electric shock: • Do not expose this product to rain or moisture. • Do not remove the rear cover. There are no user-serviceable parts inside. Refer all servicing requirements to qualified service personnel. •...
IMPORTANT INFORMATION NOTICES Important Notices Concerning Power Cord Selection The specific power cord for this LED TV is enclosed and has been selected according to the country of destination. Use the enclosed power cord to prevent electric shock. Observe the following guidelines if it is necessary to replace the original cord set, or if there is no cord set enclosed.
• If the interference persists even after performing the above measures, consult the Westinghouse Service Center or an experienced radio/TV technician for assistance. FCC Warning To assure continued FCC compliance, use a grounded power supply cord and the provided shielded video interface cable with bonded ferrite cores.
IMPORTANT INFORMATION IMPORTANT SAFETY INSTRUCTIONS Make sure to note and follow all warnings and instructions marked on the LED TV. Observe the following safety instructions. • Read these instructions. • Keep these instructions. • Heed all warnings. • Follow all instructions. •...
IMPORTANT INFORMATION Circuit Overload Do not overload wall outlets, extension cords, or power strips. This can result in a fire or electronic shock. Power Cord Protection Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them.
Do not place heavy objects on the LED TV, audio/video cables, or power cord. • If the LED TV emits smoke, abnormal noise, or a strange odor, immediately turn it off and contact the Westinghouse Service Center by: – Logging on to www.wde.com. –...
IMPORTANT INFORMATION ANTENNA INSTALLATION SAFETY Outdoor Antenna Grounding If an outside antenna or cable system is connected to the LED TV, be sure the antenna or cable system is grounded to prevent voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANS/NFPA 70, provides information on proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.
Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are registered trademarks of Dolby Laboratories. Licensing and Patent Information This WESTINGHOUSE product may be covered by one or more U.S. and foreign patents and patent applications. See http://westinghousedigital.com/compliance/ for details.
PACKAGE CONTENTS PACKAGE CONTENTS 32” LED TV Unit Remote Control (with 2x AAA batteries) LED TV Base User Manual Power Cord Warranty Card AC Adapter Warranty Brochure Screws for Base...
TERMINALS TERMINALS A UD IO IN VI DEO L IN R L OUT R Item Function 1. DC in Connects the AC to DC adapter from this outlet to a power source. 2. Audio in Connects to the audio out port of a computer. 3.
REMOTE CONTROL REMOTE CONTROL Item Description Mutes the sound. Press again to toggle the 1. Mute sound back on. Toggles the TV power on or off. 2. Power 3. Channel keys Use to key in the channel number. 4. Enter ENT Executes a channel entry.
REMOTE CONTROL OPERATION REMOTE CONTROL OPERATION INSTALLING THE REMOTE CONTROL BATTERIES CAUTIONS: • Only use AAA batteries. • Do not mix new and old batteries. This may result in cracking or leakage, which may pose a fire risk or lead to personal injury. •...
LED TV BASE LED TV BASE CAUTION: The LED TV unit may be too heavy for one person to lift. If this is the case, make sure to ask for assistance in handling the LED TV to prevent physical injury and/or damage to the unit. INSTALLING THE LED TV BASE Open the LED TV carton box.
LED TV BASE REMOVING THE LED TV BASE If you intend to repack the LED TV unit (for shipping or storage) or you want to change the installation to a wall mount option, you must first remove the LED TV base.
EXTERNAL DEVICE CONNECTIONS • A position on the RF switch (not supplied) – You can view all unscrambled channels by using the TV's channel keys. • B position on the RF switch (not supplied) – You can view the scrambled channels via the converter/descrambler by using the converter's channel keys.
Page 23
EXTERNAL DEVICE CONNECTIONS The following diagram shows the external device connections. Audio amplifier AUDIO OUT 3.5 mm stereo mini jack cable Audio cable RGB cable SPDIF cable DC IN TUNER AUDIO IN VIDEO R IN L R OUT L Antenna cable / AC to DC Cable TV line adapter...
POWER CONNECTION POWER CONNECTION CONNECTING AC POWER IMPORTANT: The LED TV is designed to be powered via an AC adapter. Use ONLY the AC adapter included in the package. Turn off all connected devices before plugging the AC adapter into the power outlet. Connect the power cord of the AC adapter to the LED TV then to a proper AC outlet.
POWER CONNECTION ANTENNA OR COAXIAL CABLE CONNECTION SETUP Select Language Use the up and down arrows on your HDTV control panel or remote control to select the language to be used for menus and messages. Press SELECT to continue. Time Zone Use the up and down arrows on your HDTV control panel or remote control to select your local time zone.
Page 26
POWER CONNECTION Select Channel Scan Type Use the up and down arrows on your HDTV control panel or remote control to select the channel scan type. Press SELECT to continue. Press Go Back to return to the previous screen. NOTE: Antenna users selecting to scan Over- the-Air ATSC channels need a Channel Access Code in order to perform a channel scan and receive broadcast signals.
Page 27
POWER CONNECTION Channel Scan in progress The channel scan may take a while to complete. When the scan is complete, you will be able to watch your local TV programming.
POWER CONNECTION CABLE OR SATELLITE BOX CONNECTION SETUP Select Language Use the up and down arrows on your HDTV control panel or remote control to select the language to be used for menus and messages. Press SELECT to continue. Time Zone Use the up and down arrows on your HDTV control panel or remote control to select your local time zone.
Page 29
POWER CONNECTION Cable/Satellite Box Input Use the up and down arrows on your HDTV control panel or remote control to select the input connected to the set top box. Press SELECT to continue. Press Go Back to return to the previous screen. RF Warning Use the up and down arrows on your HDTV control panel or remote control to select.
POWER CONNECTION OTHER INPUT SOURCE CONNECTION SETUP Select Language Use the up and down arrows on your HDTV control panel or remote control to select the language to be used for menus and messages. Press SELECT to continue. Time Zone Use the up and down arrows on your HDTV control panel or remote control to select your local time zone.
Page 31
POWER CONNECTION Select Input Source Use the up and down arrows on your HDTV control panel or remote control to select the input source. Press SELECT to continue. Press Go Back to return to the previous screen.
POWER CONNECTION WESTINGHOUSE HDTV SETUP - NOT THROUGH CABLE/ SATELLITE BOX Select Language Use the up and down arrows on your HDTV control panel or remote control to select the language to be used for menus and messages. Press SELECT to continue.
Page 33
POWER CONNECTION Select Channel Scan Type Use the up and down arrows on your HDTV control panel or remote control to select the channel scan type. Press SELECT to continue. Press Go Back to return to the previous screen. Channel Scan in progress The channel scan may take a while to complete.
BASIC OPERATIONS BASIC OPERATIONS URNING THE POWER ON AND OFF Turning on the power Press on the control panel or on the remote control to turn on the LED TV. Turning off the power Press on the control panel or on the remote control to turn off the LED TV. The LED behavior will depend on the enabled Power settings.
BASIC OPERATIONS CHANGING CHANNELS Follow the instructions below to change channels. Using the Ch Buttons Browse channels To browse through the available channels, press Ch the remote control or on the control panel. Using the Channel Keys Selecting channel To change to a certain channel, key in the channel number using the channel keys and press ENT.
BASIC OPERATIONS Using the Input Key Select source using Input Key 1 Press Input. 2 A list of supported video sources is displayed. 3 Press to select the preferred source. 4 Press to switch to the selected input source. ADJUSTING THE DISPLAY FORMAT The input source can sometimes affect the way images are displayed on-screen.
SETUP MENUS SETUP MENUS SETUP MENU OPERATION Use the setup menus to configure the various operational settings of the LED TV. Displaying the setup menu screen Press on the remote control or MENU on the control panel to display the setup menu screen.
SETUP MENUS PICTURE Use the Picture sub-menus to configure the display quality. Press on the remote control or MENU on the control panel to display the setup menu screen then select Picture to display the Picture sub-menu. The following options are available: Picture Settings, Screen Size, VGA Settings, Color temperature, Advanced Picture Settings.
SETUP MENUS Picture mode Use this sub-menu to select one of four preset view options optimized for different viewing conditions. The following options are available: • Standard: Select for standard picture. • Movie: Select for a finely detailed picture. • User: Select for standard picture.
Page 40
SETUP MENUS Color Use Color to adjust the color intensity. Adjusting Color 1 Use the keys to select Color and press 2 Press the keys on the remote control to adjust the Color level. 3 Press to save and exit the screen. Tint Use Hue to adjust the balance of the red, green, and blue colors in the display.
Page 41
SETUP MENUS 2 Press the keys on the remote control to adjust the sharpness level. 3 Press to save and exit the screen. Screen Size Press to selet the display aspect ratio till the picture is fit onto the screen. The options are different according to different input source.
Page 42
SETUP MENUS Auto Adjust Automatically adjust Clock, Phase, H-Position and V-Position settings. In order to get a good result, you should open a “filling the screen” picture before executing Auto Adjust. H.Position Shift the screen slightly to left or right. V.Position Shift the screen slightly up or down.
SETUP MENUS Phase Adjust the DB15 picture signal sampling phase. It maybe affect the definition. Wrong value maybe result the interference. Reset Reset the parameters of current menu to default value. Adjusting VGA Settings 1 Use the keys to select VGA Settings and press 2 Press the keys on the remote control to select the desired option.
SETUP MENUS Advanced Picture Settings • Dynamic Contrast (Off/On) The system will adjust the luminance curve by analyzing the picture content dynamically. • Film Mode (Off/On) For the 2:2 or 3:2 format signal of cinema, enable special pixel process to reduce the flick of moving area.
SETUP MENUS SOUND Use the Sound sub-menus to configure the sound quality. Press on the remote control or MENU on the control panel to display the setup menu screen then select Sound to display the Sound sub-menu. The following options are available: Sound Settings, Analog Sound, Digital Sound, Digital Audio Output, Equalizer Settings, and SRS TruSurround Settings.
SETUP MENUS Sound mode Use this sub-menu to select one of four preset view options optimized for different listening conditions. The following options are available: • Standard: Select for standard picture. • Soft: Select for a finely detailed picture. • User: Select for standard picture.
Page 47
SETUP MENUS Balance Use Balance to adjust the sound balance between the L/R speakers. Adjusting Balance 1 Use the keys to select Balance and press 2 Press the keys on the remote control to adjust the Balance level. 3 Press to save and exit the screen.
SETUP MENUS Equalizer Settings Use this sub-menu to select one of four preset audio options optimized for different sounding conditions. The following options are available: • Rock: Sets the equalizer to the Rock mode. • Pop: Sets the equalizer to the Pop mode. •...
SETUP MENUS CHANNEL Use the Channel sub-menus to configure the channel. Press on the remote control or MENU on the control panel to display the setup menu screen then select Channel to display the Channel sub-menu. The following options are available: Channel List, Favorite List, Channel Settings, Signal Type, Auto Channel Search.
SETUP MENUS Favorite List All of you favorite channels are listed in this menu, and you can choose them quickly. Channel Setting Set the favorite channels, skipped channels, label of channels. • Skip: Set the channel to be skipped when using CH+/CH- to view channels. •...
SETUP MENUS Change the settings • Skip & Favorite Press to select the channel you want to set. Press to highlight corresponding item, and press SELECT to set or cancel. • Label Press to select the channel and SELECT to enter the edit state. Press to select the character, press to move the cursor.
SETUP MENUS PARENTAL CONTROL Use the Channel sub-menus to configure the parental control. Press on the remote control or MENU on the control panel to display the setup menu screen then select Parental Control to display the Parental Control sub- menu.
Page 53
SETUP MENUS Rating Description TV-Y Suitable for young children. TV-Y7 May not be suitable for children under 7. TV-G Suitable for all audiences. TV-PG Parental guidance suggested. TV-14 Parental guidance suggested for children under 14. TV-MA Suitable for mature audiences only; may be unsuitable for children under 17.
Page 54
SETUP MENUS Rating Description May contain some adult material. Parents are urged to learn more about the film before letting their children view it. NC-17 May contain explicit sex scenes, an accumulation of sexually-oriented language, and/or scenes of excessive violence. Suitable for adult audiences only. Rating does not signify that the film is obscene or pornographic.
Page 55
SETUP MENUS – Canada French: Use this sub-menu to select the ratings of allowable TV programs and movies. These ratings are based on the classification categories determined by La Régie du cinéma du Québec. Rating Description Exempt shows. For general audiences. 8 ans + Not suitable for children under 8 years of age.
SETUP MENUS Change Password Change Password allows you to change your current password. Changing Password 1 Use the keys to select Change Password and press 2 Use the Channel keys to enter the current password and press 3 Use the Channel keys to enter the new password and press 4 Use the Channel keys to enter the new password again for confirmation and press 5 Press...
SETUP MENUS SETUP Use the Settings sub-menus to configure the LED TV operational setup and view the current firmware version. Press on the remote control or MENU on the control panel to display the setup menu screen then select Setup to display the Settings sub-menu. The following options are available: Closed Captions, Menu Language, Clock, OSD Timer, Power Light.
Page 58
SETUP MENUS • Digital CC Preset (Default/Custom) If set to Custom, Digital CC Style is available. The following options are available: – Closed Captions: Can be set to ON or OFF. – Analog Type: Can be set to CC1,CC2, CC3, CC4, T1, T2, T3, or T4. –...
SETUP MENUS Menu Language Use Menu Language to select the language to display on the screen: English, French, or Spanish. Adjusting Menu Language 1 Use the keys to select Menu Language and press 2 Press the keys on the remote control to select English, French or Spanish.
Page 60
SETUP MENUS • Setup Time Set Auto Clock to Off, then you can set the time manually . NOTE: In the case of loss of power, the clock setting will be lost. • Day of Week The TV will calculate current day of week according to the time. •...
SETUP MENUS OTHERS Blue Back Set the screen background color blue or not when no valid signal input. When analog TV input and has no signal, snow noise will display if this option is cleared. No Signal Power Off If it is set, TV will automatically enter standby after 10 minutes without signal input. No Operation Power Off If it is set, TV will automatically enter standby after 3 hours without any operation.
WALL MOUNT OPTION WALL MOUNT OPTION The LED TV has been fitted with VESA FPMPMI compliant mounting holes. These 200 x 100 mm mounting holes allow the unit to be mounted on a wall. Use the four M6 x L10 mm screws to wall mount the LED TV. WALL MOUNT INSTALLATION REMINDERS •...
TROUBLESHOOTING TROUBLESHOOTING Problem Corrective Action No power • Make sure the power indicator is illuminated blue. • Make sure the power cord is securely connected to the AC-in jack and is plugged into a functional AC outlet. You may want to plug in another electrical device to the power outlet to verify that it is supplying the proper voltage.
Page 64
TROUBLESHOOTING Problem Corrective Action Picture is cut off or appear Press to adjust the Aspect ratio. in a sidebar screen. Poor image quality in TV • Check your antenna connection. If necessary, mode (cutoff picture, snowy rotate the antenna and wait up to ten seconds for images).
Page 65
TROUBLESHOOTING Problem Corrective Action NOTES: If the problem condition persists even after performing the recommended corrective actions, contact us by: • Logging on to www.wde.com • Contacting the Westinghouse Customer Service at (800) 701-0680 or e-mail us at service@wde.com...
SPECIFICATIONS SPECIFICATIONS Item Specification Model Name UW32S3PW Panel Active Area 697.685 (H) x 392.256 (V) (Diagonal, mm) Resolution 1366 (H) x 768 (V) Contrast Ratio (min) 3000:1 Response Time 6.5ms(g-g) (min) Aspect Ratio 1.77 (16:9) Display color 16.7M Audio/Video •...
Page 67
SPECIFICATIONS Item Specification Physical Dimensions With stand: Specifications (WxHxD) 739.68mm x 482.13mm x 154mm Without stand: 739.84mm x 442.76mm x 53.72mm Weight (Net) 7.1Kg Weight (Gross) 9.3Kg NOTES: • These product specifications are subject to change without user notification. • Do not set your computer graphics card to exceed the unit’s refresh rates;...
Need help?
Do you have a question about the UW32S3PW and is the answer not in the manual?
Questions and answers