Download Print this page

Yamaha MA2030 Owner's Manual

Yamaha power amplifier owner's manual

Advertisement

Quick Links

ZJ24810
POWER AMPLIFIER
Owner's Manual
First, please carefully read the "IMPORTANT SAFETY INSTRUCTIONS" on the reverse side.
Thank you for your purchase of the Yamaha MA2030/PA2030 power amplifier. Please read through this
manual carefully before beginning use, so that you will be able to take full advantage of the device's
various functions. After you have read the manual, keep it in a safe place.
• The illustrations as shown in this manual are for instructional purposes only, and may appear somewhat
different from those on your device.
• The company names and product names in this manual are the trademarks or registered trademarks of
their respective companies.
• In this manual, the
mark indicates content that is unique to the MA2030, and
content unique to the PA2030. Contents that are common to both have no marks.
• Amplifier illustrations are mainly from the MA2030. Where necessary, illustrations of the PA2030 are also
shown.
Features
• Supports both kinds of speaker connection: high-impedance connection and low-impedance
connection.
• Equipped with digital processor (Feedback Suppressor, Ducker, Leveler).
• Optional PA2030 expansion amplifier enables connection of additional speakers.
Included items (please check)
• Power cord (2.0m)
• Euroblock plugs (3-pin, 3.50mm pitch) x 1
, x 2
• Technical Specifications (English only): includes block diagram, dimensions, and input/output
specifications.
• Owner's Manual (this sheet)
Setup
1
Step
Option
Speakers
2
Step
Front panel
Portable audio player,
Option
etc.
2
Step
Control Panel
Rear panel
CD players, tuners, etc.
3
Step
Option
To AC outlet
4
Step
Speaker expansion
Volume adjustment
1
Connecting Speakers
Step
Change the setting depending on the speaker connection (high- or low-impedance connection), the kind
of speakers, and the installation location of the speakers. Refer to "Connecting Speaker Cables" at the
right bottom on this page and the explanation of high-impedance connection, etc. at the following URL.
Yamaha Pro Audio site: "Better Sound for Commercial Installations":
http://www.yamahaproaudio.com/global/en/training_support/better_sound/
Caution
• Before connecting speakers, make sure that the power of the device is turned off. If the power is on, there is a risk of
electrical shock.
• Ensure that load is not applied to the speaker cable.
• In a high-impedance installation, make sure that the sum of the power input ratings of the speakers to be connected
does not exceed 60W.
• In a low-impedance installation, make sure that the total impedance of speakers to be connected is at least 3 ohms.
High-impedance Connections (60W x 1 channel)
Maximum output
Maximum output
voltage: 100V
voltage: 70V
1
Set the speaker output to high-impedance by setting the [OUTPUT] switch to
[100V] or [70V] corresponding to the maximum output voltage.
2
Use speaker cables to connect the [SPEAKERS A]
terminal to the positive "+"
terminals of the speakers, and the [SPEAKERS B]
terminal to the negative "-"
terminals.
In case of high-impedance connection, the [SPEAKERS A]
and [SPEAKERS B]
not used. Do not connect to the terminals.
Note
The speaker output is processed through a high pass filter (80Hz, 18dB/oct.).
Low-impedance Connections (30W x 2 channels)
EN
Speaker impedance
1
Set the speaker output to low-impedance connection by setting the [OUTPUT] switch
to [4Ω 3Ω].
2
Set the [SETUP] DIP switch 1 to [4Ω] (up, impedance: 4Ω or more) or [3Ω] (down,
impedance: 3Ω to 4Ω) corresponding to the specifications of the speakers to be
connected.
3
Connect the [SPEAKERS A]
/
terminals to the "+"/"-" terminals of the first
speaker, and the [SPEAKERS B]
/
terminals to the "+"/"-" terminals of the second
speaker.
indicates
Configuration of Speaker Output Signal
Connecting Yamaha Speakers
Setting mono/stereo output
[SETUP] DIP switch 4/5
[SETUP] DIP switch 7
Setting the [SETUP] DIP switches optimizes the
In a low-impedance installation, if speakers are
output signal to match Yamaha speakers designed
placed in a stereo arrangement, set to stereo
for commercial installations.
output.
[SETUP] DIP switch
4
5
[SETUP] DIP switch
Surface
High-impedance
Yamaha speakers
down
up
mount-type
connections
designed for
commercial installations
Ceiling-type down
down
Low-impedance
connections
Non-Yamaha speakers
up
—: Setting is not required. (Either up or down can be used.)
—: Setting is not required. (Either up or down can be used.)
*1: When stereo audio is output, the left channel signal
is output from the [SPEAKERS A] terminals and the
right channel signal is output from the [SPEAKERS B]
terminals.
2
Connecting External Devices
Step
1
RCA type
RCA type
mini-stereo
type
Microphones
2
MA2030 front panel
MA2030 rear panel
Connect a BGM (background music) tuner, a CD player, a portable audio player, etc. to the stereo input jacks
(DCP1V4S)
of this device.
Jack position
Jack name
Front panel
[ST IN 1] jack
mini-stereo type (unbalanced input)
3
MA2030
[ST IN 2] jack
Rear panel
RCA type (unbalanced input)
[ST IN 3] jack
Euroblock connector (balanced input; connect with supplied
PA2030
Rear panel
[LINE IN] jack
Euroblock plugs), RCA type (unbalanced input)
Note
Refer to "Attaching Euroblock Plugs" for Euroblock plug installation.
1
Make sure that this device and all devices to be connected are turned off.
2
Connect this device and any external devices with appropriate cables.
Leveler (suppressing wide playback volume variations)
[SETUP] DIP switch 6
The Leveler function automatically suppresses and corrects for large changes
in the playback volume from external devices for a more consistent sound,
such as when reproducing BGM (background music).
3
Connecting Power Cord and Turning On
Step
AC IN connector
MA2030 front panel
MA2030 rear panel
1
Make sure power switches of this device and devices connected to this device are
turned off (in
position).
2
Turn the [VOLUME] knob all the way to the left.
3
Connect the supplied power cord to the AC IN connector.
4
Insert the power cord plug into an appropriate outlet.
5
After turning on the connected devices (portable audio players, CD players, etc.), turn
on this device.
Note
• Before turning on the power, please check that there are no problems with the cabling, connections, and so on.
• When turning the system off, turn off this device, and then connected devices.
terminals are
4
Adjusting Volume
Step
[SETUP] DIP switch
1
4Ω or more
up
MA2030 front panel
3Ω to 4Ω
down
1
Select a stereo input by rotating the [ST SOURCE] knob.
The [ST SOURCE] indicator corresponding to the selected input signal lights.
2
Input audio signal from the external device, and confirm that sound is being output
from the speakers by gradually rotating the [VOLUME] knob to the right.
Make sure that the [VOLUME SIGNAL] indicator lights according to the sound input and that sound
comes from the speakers.
Matching the volume levels of external devices
When connecting two or more external devices, you can lower the volume of the louder devices to match the
level of the faintest device.
1
Select the stereo input with the loudest sound by rotating the [ST SOURCE] knob.
2
Press and hold the [ST SOURCE] knob until the [ST SOURCE] indicator flashes.
3
Rotate the [ST SOURCE] knob to the left until the volume decreases to the point that
lowers as loud as that of the faintest sounding stereo input.
As the volume becomes fainter, the flashing rate of the [ST SOURCE] indicator becomes slower.
4
Push the [ST SOURCE] knob to complete the adjustment.
The [ST SOURCE] indicator lights.
Note
Adjustable range: -18dB – 0dB
7
Mono output
1
Option
Using Microphones
up
Mono output
down
Stereo output (*1)
MA2030 has two microphone inputs. We recommend that you first set the playback volume of the external
devices before adjusting the volume balance of the microphones.
Phone
XLR
Euroblock
MA2030 front panel
1
Turn the [MIC IN 1] knob or the [MIC IN 2 GAIN] trimmer all the way to the left.
2
Connect a microphone to the [MIC IN 1] jack or the [MIC IN 2] connector.
3
Gradually turn the [MIC IN 1] knob or the [MIC IN 2 GAIN] trimmer to the right while
inputting signal to a microphone, making sure that sound is output from the speakers.
You can also confirm the [MIC IN 1] jack input signal by the [MIC IN 1] indicator.
Note
• To adjust the [MIC IN 2 GAIN] trimmer, use a slotted screw driver.
PA2030 rear panel
• Refer to "Attaching Euroblock Plugs" for installation of Euroblock plugs.
• The input signal is always processed through a high pass filter (120Hz, 12dB/oct.) to cut off low frequency signals
as well as a Feedback Suppressor to suppress howling.
• If it is difficult to match the volume balance of the stereo input and the microphone input, lower the stereo input
volume (refer to "Matching the volume levels of external devices" in "Step 4 Adjusting Volume") and then adjust the
Jack type
microphone input volume with the [MIC IN 1] knob or the [MIC IN 2 GAIN] trimmer.
Ducker (lowering the volume of the other channels automatically when a
microphone signal is input)
[SETUP] DIP switch 2/3
Jack/connector
[MIC IN 1]
[SETUP] DIP switch
2
Ducker disabled
up
Ducker enabled
down
2
[SETUP] DIP switch
6
Option
Operating with Control Panel
Leveler disabled
up
Leveler enabled
down
Connecting Yamaha Digital Control Panel DCP1V4S to MA2030 enables you to control the volume, to switch
inputs, etc. remotely.
RJ-45
Power cord
To AC outlet
MA2030 rear panel
Ethernet straight cable
(CAT5e or more; 200m or less)
The functions of the knob and the switches of DCP1V4S can be configured with DIP switches at the back of
DCP1V4S.
Panel
DIP switch
Knob
Switch 1
ID
1 2 3 4
0
Stereo 1
1
2
Mic. 1
3
Mic. 1
Volume
4
Mic. 1
5
Mic. 2
Mic. 1
6
7
Mic. 1
Note
Refer to "DCP1V4S Owner's Manual" for DCP1V4S installation.
Option
PA2030 front panel
Connecting the MA2030 and PA2030 lets you increase the number of driven speakers. Connect the [LINE
OUT] jacks of MA2030 and the [LINE IN] jacks of PA2030.
Connecting Speaker Cables
The [SPEAKERS] output connectors on the rear panel are barrier strip type connectors. The connections
are described below for two methods: using a spade lug and using a bare conductor.
Caution
Ensure that load is not applied to the speaker cable.
Note
Connect the cables so that the amplifier's "+" and "-" symbols match those of the speaker. If they are reversed,
the phase will be reversed and the sound will not be output correctly.
When using a spade lug
Loosen the screw, insert the spade lug all the
way from below, and tighten the screw.
≥3.2mm
(≥ 0.13")
≤5.8mm
Euroblock
(≤0.23")
Attaching Euroblock Plugs
MA2030 rear panel
1
Terminal
screw
Euroblock plug
Note
• You must use the supplied Euroblock plugs. If the plugs have been lost, please contact your Yamaha dealer.
• To prepare the cable for attachment to a Euroblock connector, strip the wire as shown in the illustration using
• Do not tin (solder) the exposed end.
[MIC IN 2]
Note
• If both Duckers of the [MIC IN 1] jack and the [MIC
1
Loosen terminal screws.
3
IN 2] jack are enabled, the Ducker for the [MIC IN
2
1] takes priority.
up
Insert cables.
• Activating the Ducker lowers the output volume of
3
down
the stereo inputs by 24dB and mutes that of the
Securely tighten terminal screws.
other microphone input.
4
Insert the Euroblock plug into the [MIC IN 2] terminal of MA2030 or the [LINE IN]
terminal of PA2030.
Panel Lock
Yamaha Digital Control Panel
Changes by several knobs can be locked, so that the settings of the device are not affected by accidental
DCP1V4S
touch or unauthorized operation. The [ST SOURCE], [SOURCE EQ BASS] and [SOURCE EQ TREBLE]
(maximum: one unit)
knobs can be locked.
1
Adjust the [ST SOURCE], [SOURCE EQ BASS] and [SOURCE EQ TREBLE] knobs
Rear panel
to the desired fixed settings.
When connecting to MA2030,
ON
2
set the DIP switch 4 to ON
Turn off the power.
(termination setting).
1
2
3
4
3
Set DIP switch 8 to the downward position.
Sets the panel ID
4
Turn the power back on again.
Note
To unlock, turn off the power, set DIP switch 8 to the upward position, and turn on the power.
Volume: Adjusts the volume output
Switch 2
Switch 3
Switch 4
to the [SPEAKERS] terminals and
the [LINE OUT] jacks.
Stereo 1/2/3: Switches to stereo
input 1/2/3.
Mic. 1/2: Turns on/off microphone
Stereo 2
Stereo 3
input 1/2. When a microphone
is on, the switch indicator of the
Mic. 2
Mic. 1
Mic. 2
control panel lights and the stereo
input is muted.
Mic. 2
Mic. 1
Mic. 2
• If the panel ID is set to 3, the
stereo input is not muted even
though the microphone is on.
Mic. 1
• If the panel ID is set to 7, the
microphone stays on while
Mic. 2
holding the switch.
: A chime sounds when the
Mic. 2
microphone is turned on/off
—: Does not work. (No function is
assigned.)
Mic. 2
3
Expanding Speakers
RCA
RCA
MA2030 rear panel
PA2030 rear panel
When using a bare conductor
Loosen the screw, wrap the conductor wire around
the barrier strip terminal, and tighten the screw. Be
sure that the bare wire does not touch the chassis.
Speaker cable
Wire
should not
touch the
chassis.
15mm*
(0.6")
* Actual size
2
3
4
Loosen
Approx. 5 mm
Slotted
(approx. 0.2")
Tighten
screwdriver
stranded wire to make connections. With a Euroblock connection, stranded wires may be prone to breakage
because of metal fatigue due to the weight of the cable or due to vibration. When rack mounting your device,
use a lacing bar when possible to bundle and fasten the cables.

Advertisement

loading

Summary of Contents for Yamaha MA2030

  • Page 1 Jack name Jack type • You must use the supplied Euroblock plugs. If the plugs have been lost, please contact your Yamaha dealer. microphone input volume with the [MIC IN 1] knob or the [MIC IN 2 GAIN] trimmer. • To prepare the cable for attachment to a Euroblock connector, strip the wire as shown in the illustration using...
  • Page 2 España the [LINE OUT] jacks of the MA2030 or output jacks of other external devices. The signals input from the RCA type jacks are using is easily accessible. If some trouble or malfunction Rua Joaquim Floriano, 913 - 4º...

This manual is also suitable for:

Pa2030