Advertisement
Quick Links
Service Manual
SPECIFICATIONS
(Information in brackets [ ] refers to model TX-28PM1)
Power Source:
220-240V a.c., 50Hz
Power Consumption:
86W [78W]
Stand-by Power
Consumption:
1,3W
Aerial Impedance:
75 unbalanced, Coaxial Type
Receiving System:
PAL-I, PAL-525/60
M.NTSC (AV only)
NTSC (AV only)
Receiving Channels:
VHF A1-S20
UHF E21-E69
CATV S21-S41 (Hyperband)
Intermediate Frequency:
Video/Audio
Video
38,9MHz
Audio
32,9MHz
32,35MHz (NICAM)
Colour
34,47MHz
Terminals:
AUDIO MONITOR OUT
Audio (RCAx2) 500mV rms 1k
AV1 IN
Video (21 pin)
Audio (21 pin)
RGB (21 pin)
AV1 OUT
Video (21 pin)
Audio (21 pin)
AV2 IN
AV2 OUT
AV3 IN
High Voltage:
Picture Tube:
Audio Output:
Headphones:
Accessories
supplied :
Dimensions:
Height:
Width:
Depth:
1V p-p 75
500mV rms 10k
Net weight:
0,7V p-p 75
1V p-p 75
500mV rms 1k
Specifications are subject to change without notice.
Weights and dimensions shown are approximate.
ORDER No. 04-SM-001
Colour Television
TX-32PM1
TX-28PM1
GP4 Chassis
Video (21 pin)
1V p-p 75
Audio (21 pin)
500mV rms 10k
S-Video IN
Y: 1V p-p 75
(21-pin)
C:0,3V p-p 75
Video (21 pin)
1V p-p 75
Audio (21 pin)
500mV rms 1k
S-Video IN
Y: 1V p-p 75
(4-pin)
C:0,3V p-p 75
Audio (RCAx2)
500mV rms 10k
Video (RCAx1)
1V p-p 75
32kV ± 0,9kV [31kV ± 1kV]
W76EKX50X21
76cm
[W66MAF185X03 66cm]
2x7W RMS, 2x15W MPO,
8 impedance
8 Impedance
Remote Control
2 x R6 (UM3) Batteries
566mm
[515mm]
902mm
[766mm]
550mm
[529mm]
56kg
[38kg]
Panasonic CS ( U.K. ) Ltd.
WILLOUGHBY ROAD,
BRACKNELL,
BERKS.,
RG12 8FT.
Advertisement
Related Manuals for Panasonic TX-32PM1
Summary of Contents for Panasonic TX-32PM1
-
Page 1: Service Manual
0,7V p-p 75 AV1 OUT Video (21 pin) 1V p-p 75 Audio (21 pin) 500mV rms 1k Specifications are subject to change without notice. Weights and dimensions shown are approximate. Panasonic CS ( U.K. ) Ltd. WILLOUGHBY ROAD, BRACKNELL, BERKS., RG12 8FT. -
Page 2: Waveform Pattern Table
WAVEFORM PATTERN TABLE CONDITIONS: Contrast: MAX, Brightness: MID, Colour: MID, Sharpness: MID... -
Page 3: Alignment Settings
ALIGNMENT SETTINGS (The figures below are nominal and used for representative purposes only.) Set the Bass to maximum position, set the Treble to minimum position, set the Volume to minimum then press the down button (-/v) on the customer controls at the front of the TV and at the same time press the INDEX button on the remote control, this will place the TV into the Service Mode 1. - Page 4 JK3201 L OUT P L OUT M R OUT M R OUT P AA_AV3_IL AA_AV2_IL L IN AA_AV1_IL L OUT AA_AV3_IR AA_AV2_IR R IN AA_AV1_IR R OUT AA_AV2_OR C_IN AA_AV2_OL VIDEO/Y IN AA_AV1_OR VIDEO OUT AA_AV1_OL L IN L OUT R IN R OUT AA_AV2_C...
- Page 5 SERVICE POWER BUS Degauss Mains In coil...
- Page 6 SERVICE/TEST AV LINK2 SLOW2 FBIN SDA_SW2 SCL_SW2 3,3SCL SLOW1 3,3SDA RESET XTAL2 XTAL1...
- Page 7 ROTATION COIL DEFLECTION IC601 MICROPROCESSOR...