Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for LOUD Technologies S410s
- Page 1 S410s REPAIR MANUAL S410s REPAIR MANUAL...
-
Page 2: Table Of Contents
These instructions are intended to help restore any ailing S410s Passive Subwoofer back to factory working conditions. They show how to remove and replace the drivers and input assembly. Please contact Mackie Technical Support (1-800-898-3211) to receive a Service Request Number and Order Number for parts needed for this restoration. They will also help you determine the nature of the problem and what parts will repair the unit. -
Page 3: Part #0011737
Top left woofer replacement: Eight screws need to be removed Six screws need to be removed from from the woofer using the phillips head each side of the front of the grill (twelve screwdriver. Once the screws are screws total) using the phillips head removed, the woofer may be loosened screwdriver. -
Page 4: Part #0011737
Place the new woofer (part #0011737) where the old one was. Follow the same steps as above, but backwards 4 to 1. Power up the S410s and the new woofer should now be pumping out glorious lows. Awesome, you just replaced a 10”... -
Page 5: Part #0011737
Top right woofer replacement: Eight screws need to be removed Six screws need to be removed from from the woofer using the phillips head each side of the front of the grill (twelve screwdriver. Once the screws are screws total) using the phillips head removed, the woofer may be loosened screwdriver. -
Page 6: Part #0011737
Place the new woofer (part #0011737) where the old one was. Follow the same steps as above, but backwards 4 to 1. Power up the S410s and the new woofer should now be pumping out glorious lows. Awesome, you just replaced a 10”... -
Page 7: Part #0011737
Bottom left woofer replacement: Eight screws need to be removed Six screws need to be removed from from the woofer using the phillips head each side of the front of the grill (twelve screwdriver. This woofer has a tendency screws total) using the phillips head to want to pop out, so please be sure to screwdriver. -
Page 8: Part #0011737
(part #0011737) where the old one was. Caution: The woofer is approximately Follow the same steps as above, but 8 pounds with the weight unevenly backwards 4 to 1. Power up the S410s distributed. and the new woofer should now be push down push down pumping out glorious lows. -
Page 9: Part #0011737
Bottom right woofer replacement: Eight screws need to be removed Six screws need to be removed from from the woofer using the phillips head each side of the front of the grill (twelve screwdriver. This woofer has a tendency screws total) using the phillips head to want to pop out, so please be sure to screwdriver. -
Page 10: Part #0011817
Caution: The woofer is approximately Follow the same steps as above, but 8 pounds with the weight unevenly backwards 4 to 1. Power up the S410s distributed. and the new woofer should now be pumping out glorious lows. Awesome, you just replaced a 10” woofer! -
Page 11: Part #0011817
Input assembly replacement: Eight screws need to be removed from the input assembly (located on the rear of the cabinet) using the phillips head screwdriver. Once the screws are removed, the input assembly may be loosened by prying a fl at head screwdriver in between it and the cabinet. - Page 12 (as shown in the picture above) and place on the new input assembly. Power up the S410s and relish in the fact that you just J3 J3 J4 J4 replaced an input assembly. Hats off to...
- Page 13 This page left blank intentionally...
Need help?
Do you have a question about the S410s and is the answer not in the manual?
Questions and answers