Advertisement
•You must use a Class 2 power
!
source that supplies 12V DC and
delivers at least 500 mA. Its center
tip must be set to positive and its
plug must fit the antenna's DC 12V jack. The
supplied adapter meets these specifications.
Using an adapter that does not meet these
specifications could damage the antenna or
the adapter.
• Always connect the AC adapter to the
antenna before you connect it to AC power.
When you finish, disconnect the adapter from
AC power before you disconnect it from the
antenna.
±
±
• Your local RadioShack store has accessories
you can use to connect the antenna to your
TV set or FM receiver if they do not have a
75-ohm antenna terminal.
• We recommend you using your existing TV
remote control to learn channel and antenna
angle settings so you can control your TV and
this antenna synchronously.
• If the antenna does not learn the remote
control signals properly, adjust the distance
between them until the antenna learns the
signal.
• The antenna is preset to learn 15 function
signals in sequence. If you do not press the
keys in the same sequence as Step 4, the
antenna may not function properly.
• The antenna learns one key at a time. Each
time you press a remote control's key, the
/Q
antenna learns that key.
appears,
confirming that the key was successfully
/Q
stored. Press the next key when
• During the learning process, if you do not
press each function key on the remote control
within 10 seconds, the antenna automatically
turns off and you must start again at Step 1.
• On a universal remote control, you can
assign the equivalent keys like MEM,
J
RESET, /REW, and FFWD/
for MEMORY,
CLEAR, L-TUNING ( ) and R-TUNING (
functions.
• If you press MEMORY for 4 seconds after the
antenna completes learning, the previously
learned signals will be deleted. Use the
existing remote control or universal remote
control and begin signal learning again from
Step 1.
• Be sure the antenna's learning setup does
not affect the setup of other existing
equipment.
•
appears when you turn on the antenna's
power for the first time.
• Pressing MEMORY for 4 seconds deletes the
previously learned signals but does not
delete the stored antenna angles.
2
TO TV
CABLE IN
Power the antenna using the supplied 12V,
500 mA AC adapter.
1. Place the antenna on or near your TV
set or FM receiver.
2. Connect the antenna's coaxial cable to
your TV set's 75-ohm UHF/VHF terminal
or your FM receiver's 75-ohm antenna
terminal. ±
3. If you want to use a second video source
such as cable TV, a satellite dish, or a
video game system, connect it to the
antenna's
CABLE IN
ohm coaxial cable/connector (not
supplied) (See "Setting a Secondary
Source" on Page 3).
4. Insert the supplied AC adapter's small
barrel plug into the
back of the antenna's base.
appears.
5. Plug the AC adapter into a standard AC
b
outlet.
appears to indicate the power
is turned off.
J
)
Your antenna can learn up to 15 remote
control functions from the remote control so
you can adjust the antenna angle by using
the remote control. To learn all 15 remote
control functions, your TV's remote control
must have the equivalent
(I) and
L-TUNING
R-TUNING
replace same key functions on the antenna. If
not, just set the antenna to learn 11 signals
and manually press the above four keys on
the antenna base during the operation. The
antenna uses the latest integrated circuit
recording technology to retain the learned
function even if AC power fails. ±
1. Be sure the antenna's power is turned
b
off.
appears.
2. Hold down
base for 4 seconds until
3. Point the remote control at the display on
the front of the antenna base.
4. If your remote control has the equivalent
keys to replace the antenna's
CLEAR
functions, press the following 15 keys in
sequence: ±
POWER
7
8
L-TUNING
b
appears when learning is complete.
If the remote control does not have the
+/– GAIN
DC 12V
equivalent keys to replace
CLEAR
functions, press the following 11 keys in
sequence. Then press
complete learning. ±
POWER
7
8
b
appears when learning is complete.
terminal using a 75-
The antenna can store up to 50 memorized
best reception antenna angles, selecting
from channel 1-99. Follow these steps to
store the antenna angles for the selected
channels.
jack on the
DC 12V
1. Point the remote control at the TV to turn
on the TV and the antenna.
set channel number appears on the
antenna's display.
2. Use the remote control to enter the
desired channel number on the antenna.
For example, press 0 then 2 for channel
2. The selected channel number
appears for a few seconds,
briefly, then the channel number appears
on the antenna's display window.
3. Press
the antenna base or the assigned L-
TUNING (I) and R-TUNING (J) keys on
,
,
MEMORY
CLEAR
the remote control to adjust the antenna
(J) keys to
angle until your TV gets the best
reception for that channel.
4. Press
the assigned MEMORY key on the
remote control.
on the antenna
MEMORY
/Q
appears.
,
MEMORY
,
(I) and
(J)
L-TUNING
R-TUNING
1
2
3
4
5
6
9
0
MEMORY
CLEAR
R-TUNING
,
MEMORY
,
, and
L-TUNING
R-TUNING
to
MEMORY
1
2
3
4
5
6
9
0
or the last
(U
flashes
(I) and
(J) on
L-TUNING
R-TUNING
on the antenna base or
MEMORY
flashes.
Advertisement
