Control Output Output Mode Mode Mode iPort main circuit board, as shown in Figure 1 . Switch Switch Switch Note: Component and S-Video output are only available in the IW-21 and IW-22 models with the Balanced Video Upgrade Kit installed, and is dependent on the specific iPod model.
Page 5
Note: Extended control is only available in the IW-22, and in IW-21 units with RS-232 and Balanced Audio Upgrade Kits installed. iPort Rear Connections See Figure 2 Figure 2: iPort Rear Connections Audio Connector: RJ-45 jack Roto-Lock Clamp Audio Connector...
(all models) Note: You can mount the iPort directly next to a wall stud on either side (see Step 8, on page 8). i Po r t I W- 2 0 / I W- 2 1 / I W- 2 2...
Page 7
IW-20 Connections and Installation See Figure 4 Figure 4: iPort IW-20 System Connections 5/RJ-45 C ABLE — UP TO FEET NOT INCLUDED RJ-45 Audio Local-Zone Connector iPort Audio System Audio Wall Plate UDIO TEREO Connectors RCA C ABLE NOT INCLUDED...
Page 8
IMPORTANT: Do not install the iPort wall plate in the same elec- Figure 5: Attaching the Utility Box to a Wall trical box as AC house wiring, a light switch, or any other high- voltage device or control. The wall plate can share gang boxes...
Page 9
IW-21 Connections and Installation See Figure 7 Figure 7: iPort IW-21 System Connections 5/RJ-45 C Local-Zone Audio System ABLE UP TO FEET NOT INCLUDED NBALANCED RCA C IDEO ABLE ABLE INCLUDED UP TO FEET NOT INCLUDED RJ-45 Video To RCA...
Page 10
IMPORTANT: Do not install the iPort wall plates in the same electrical boxes as AC house wiring, a light switch, or any other high-voltage device or control. The two wall plates can share a gang box with each other or with controls such as A/B speaker switches, infrared receivers, and volume controls, if these other devices are rated as Class 2 devices according to the National Electrical Code.
Page 11
Note: The circuit card will only fit into the connector one way. Although the circuit card fits somewhat loosely, when the iPort face is inserted into the utility box it holds the card in place. i Po r t I W- 2 0 / I W- 2 1 / I W- 2 2...
Page 12
Note: The circuit card will only fit into the connector one way. Although the circuit card fits somewhat loosely, when the iPort face is inserted into the utility box it holds the card in place. iPort IW-22 Connections and Installation...
Page 13
Figure 10: iPort IW-22 System Connections 5/RJ-45 C ABLE — UP TO FEET NOT INCLUDED NBALANCED RCA C IDEO ABLE ABLE INCLUDED UP TO FEET NOT INCLUDED 1 – 2 3 – 4 5 – 6 7 – 8 AUTO ON...
Page 14
Position IR/RS-232 Control IMPORTANT: Do not install the iPort wall plates in the same electrical Switch boxes as AC house wiring, a light switch, or any other high-voltage device or control. The two wall plates can share a gang box with each...
Page 15
Note: The Roto-Lock system can accommodate a maximum wall material thickness of 1 ”. IMPORTANT: NEVER over-tighten the Roto-Lock screws. IMPORTANT: Do not over-tighten the drywall screw. Adjusting the iPort for Different iPod Models Figure 13: Adjusting the iPort for Different iPod Models ROTATE...
Page 16
Controlling the iPod in an iPort System i Po r t I W- 2 0 / I W- 2 1 / I W- 2 2 I n s t r u c t i o n M a nu a l...
Status Indicator Always OFF Mode: Note: If power to the iPort is lost or the power supply is disconnected, the Status Indicator will return to the factory default settings. Specifications i Po r t I W- 2 0 / I W- 2 1 / I W- 2 2...
Page 18
i Po r t I W- 2 0 / I W- 2 1 / I W- 2 2 I n s t r u c t i o n M a nu a l...
Page 19
Notes: i Po r t I W- 2 0 / I W- 2 1 / I W- 2 2 I n s t r u c t i o n M a nu a l...
Need help?
Do you have a question about the IW-20 and is the answer not in the manual?
Questions and answers