Related Manuals for SecurityMan PalmWatch II
Summary of Contents for SecurityMan PalmWatch II
- Page 1 SecurityMan ® PalmWatch II 2.4GHz Wireless Color Baby Monitor System with Night Vision, Audio Detection, & Camera Rechargeable Battery...
- Page 2 The content of this manual is furnished for informational use only, is subject to change without notice, and should not be construed as a commitment by SecurityMan. SecurityMan assumes no responsibility or liability for any errors or inaccuracies that may appear in this book.
- Page 3 Limitation of Liability The liability of SecurityMan arising from this warranty and sale shall be limited to a refund of the purchase price. In no event shall SecurityMan be liable for costs of procurement of substitute prod- ucts or services, or for any lost profits, or for any consequential, incidental, direct or indirect dam- ages, however caused and on any theory of liability, arising from this warranty and sale.
- Page 4 1 feet away from any heart pacemaker. Radio waves might potentially influence heart pacemaker and lead to respiratory disturbance. DO NOT use this product for any illegal activities. SecurityMan shall not be responsible for any consequences of illegal conducts by users.
- Page 5 Conditions Please read the following messages to make sure whether your working envi- ronment is suitable. • Ensure there is enough space around the receiver for ventilation. • The temperature should be kept between –10˚C and 40˚C (14F – 104˚F). The relative humidity should remain from 20% to 80%.
-
Page 6: Table Of Contents
Setting up the monitor (Receiver) ......10 Optimizing the PalmWatch II ......10 Multi-Camera Operation . -
Page 7: Introduction
Thank you for purchasing the PalmWatch II. The PalmWatch II consists of a wireless palm LCD monitor and a wireless color day & night BabyCam. PalmWatch II is an ideal product for monitoring a baby, an elder or a patient. Features: •... -
Page 8: Installation
Installation Setting up the camera (Transmitter) 1. Unpack the camera 2. Decide on wall or desk mounting the camera. (For wall mounting instruction, please refer to “Drilling Template for Wall Mounting Camera(s)” section) Note: The Rechargeable Battery Pack should not be used if you decide to wall mount the camera. - Page 9 5) To get the best performance from the camera, please follow the guidelines below: i) For best performance, mount the camera between 12ft and 16ft above the detected area. ii) Built-in IR sources (8 LEDs) provide night vision, for day use please turn off the LEDs by sliding the NIGHT VISION SWITCH (on the right side of camera head) to the OFF position.
-
Page 10: Setting Up The Monitor (Receiver)
5) The monitor (receiver) setting is now completed. Optimizing the Palmwatch II The 2.4GHz video signals pass easily through your home’s interior walls, but the signal may be reflected by power wire or plumbing inside the wall. The most common source of interference are microwave ovens. -
Page 11: Multi-Camera Operation
Multi-Camera Operation The PalmWatch II is designed to support up to 3 cameras. Additional cam- eras are sold separately. Please check for product availability. Important: When using more than one camera, make sure each camera is assigned to specific channel by adjusting the corresponding SLIDE SWITCH to position 1, 2, or 3. - Page 12 Menu Auto Power Scan Alarm Volume Manual Volume POWER • Press to turn the palm monitor ON/OFF. • When using the battery source on the palm monitor, the built-in LED of the POWER button will flash to indicate low battery status between 2.5 to 3.5 hours after initial use.
- Page 13 MANUAL To select a specific camera on the palm monitor, press the MANUAL button. The palm monitor will switch to a different camera each time the MANUAL button is pressed. To avoid searching for channels that do not have cameras assigned, set the DIP SWITCH (located on the back panel of the palm moni- tor for those corresponding channels up to the OFF position.
-
Page 14: Rechargeable Battery Pack
Note: The battery pack BP200 must be fully charged for 12 hours before independent use. Plug the PalmWatch II camera AC adapter (9V 400mA) connector into the DC jack at the end of the Battery Pack (9V 400mA). Plug the adapter itself into an electrical outlet. -
Page 15: Installing The Rechargeable Battery Pack To Camera
Installing the Rechargeable Battery Pack to camera Connect to Power Supply You can operate the camera with the rechargeable Battery Pack connected to it. Power Jack for camera AC adapter (9V 400mA) on rechargeable Battery Pack You can also operate the camera without the Battery Pack. Power Jack for camera AC adapter (9V... -
Page 16: Troubleshooting
Troubleshooting If you are having trouble operating this product, please follow the guide below: Issues Solution No Camera Picture 1) Check all connectors. Make sure camera(s) and palm monitor are switched ON. 2) Ensure camera(s) & palm monitor are set to correct channel(s). -
Page 17: Specification
Specification Camera (SM-200T) TV System NTSC (color) standard Integrated Lens 5.6mm, fixed focus Resolution 360 horizontal TV lines Signal/Noise Ratio 48dB Image Sensor 1/3” CMOS Min. illumination 0.5 lux Current Consumption 120mA~300mA Frequency Range 2,414, 2,432 & 2,468MHz Dimension (WxHxD) 3.75”... -
Page 18: Drilling Template For Wall Mounting Camera(S)
Drilling Template for Wall Mounting Camera(s) To wall mount camera(s), drill two holes using a 1/4” drill bit and the template below. (Please keep a copy of this template for future reference) Insert supplied wall anchors into holes and secure camera to wall with sup- plied screws. - Page 20 www.securitymaninc.com...
Need help?
Do you have a question about the PalmWatch II and is the answer not in the manual?
Questions and answers