SAFETY PRECAUTIONS IMPORTANT SAFETY NOTICE Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and Replacement Parts List. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent Shock, Fire, or other Hazards.
SERVICING PRECAUTIONS CAUTION: Before servicing receivers covered by this service unit under test. manual and its supplements and addenda, read and follow the 2. After removing an electrical assembly equipped with ES SAFETY PRECAUTIONS on page 3 of this publication. devices, place the assembly on a conductive surface such as NOTE: If unforeseen circumstances create conflict between the aluminum foil, to prevent electrostatic charge buildup or...
Page 5
IC Remove/Replacement Some chassis circuit boards have slotted holes (oblong) through Circuit Board Foil Repair which the IC leads are inserted and then bent flat against the Excessive heat applied to the copper foil of any printed circuit circuit foil. When holes are the slotted type, the following technique board will weaken the adhesive that bonds the foil to the circuit should be used to remove and replace the IC.
SPECIFICATION NOTE : Specifications and others are subject to change without notice for improvement. 1. Application range 3. Test method This specification is applied to LP62F chassis. 1) Performance : LGE TV test method followed 2) Demanded other specification 2. Requirement for Test Safety : CE, IEC Specification EMC : CE, IEC Testing for standard of each part must be followed in below...
5. General Specification Item Specification Remark Panel 32”, 37", 42" TFT WXGA LCD Frequency range H : 31 ~ 61Khz, V : 56 ~ 75Hz PC Input Control Function 1) Contrast/Brightness 2) H-Position / V-Position 3) Tracking : Clock / Phase 4) Auto Configure 5) Reset Component Jack...
Page 8
6. Model Specification Item Specification Remark Market Broadcasting system PAL BG/I/DK, SECAM Available Channel BAND VHF/UHF C1 ~ C69 CATV S1 ~ S47 Receiving system Upper Heterodyne SCART Jack(2EA) PAL, SECAM, NTSC 4 System : PAL, SECAM, NTSC, PAL60 Video Input (2EA) PAL, SECAM, NTSC 4 System : PAL, SECAM, NTSC, PAL60...
Page 9
8. RGB Input ( PC ) Resolution H-freq(kHz) V-freq.(kHz) Pixel clock(MHz) Remarks 720 x 400 31.469 70.08 28.32 640 x 480 31.469 59.94 25.17 VESA(VGA) 640 x 480 37.500 75.00 31.50 VESA(VGA) 800 x 600 37.879 60.31 40.00 VESA(SVGA) 800 x 600 46.875 75.00 49.50...
Page 10
Indi Wooden Indi Wooden Stand Assy Type Attached ( detachable ) Size( W x D x H ) 488.2 Tilt Degree Without Tilt function Tilt force Swivel Degree Swivel Force Appearance General Refer to Standard of LG(55)G1-1020 - 10 -...
1. Application Range 4.1. EDID Data This spec. sheet is applied to all of the LP62F chassis(H3- Item Data Condition High) manufactured at LG TV Plant all over the world. Manufacturer ID 1E6D Version Digital : 1 Revision Digital : 3 2.
5. ADC Calibration 4) It is very import to use correct adjustment pattern like Fig.1. - Within the pattern, color sequence should be aligned AV ADC Condition Component DVI(RGB) : White-Yellow-Cyan-Green-Magenta-Red-Blue-Black (If color sequence is reversed (Black -> ... -> White), NTSC Model : 217 Model : 3...
Page 13
* Test Equipment 2) AUO Module Color Analyzer (CA-110) Data PC(For communication through RS-232C) Command1 Command2 Set ID =>UART Baud rate : 115200 Pattern Generator (MSPG-925FA etc.) Input Select R-Gain *Target Value [ PSM: Standard(ZH/TH), CSM: Normal] G-Gain - Normal(9300K±1000K) x:283±0.015, y: 298±0.015 - Luminance(Y) B-Gain AV/COPM : Min.
Page 14
7.2. Detail list of SVC option data Adjustment SET ID VAL Remark WHITE BALANCE “J”(A~F) RED GAIN 0~99 0~3F 0:0, 3F:3F, FF : the state marking SYS. GREEN GAIN 0~99 0~3F 0:0, 3F:3F, FF :the state marking Option 1 Option 2 Option 3 Option 4 Option 5...
Page 15
8. Shipping Conditions Item Condition Remark Power Volume Level Main Picture Input Main Last Channel Pr 01 Mute 16 : 9 Station Auto Programme Manual Programme Programme Edit Favorite Programme None Picture Dynamic Dynamic Contrast Brightness Colour Sharpness Normal Auto Advanced Reset Sound...
TROUBLESHOOTING 1. No power Start check 6. Check the VSC low pressure output It is Doesn’t Is the Interface identical with power the screen whole signal operated? off condition? come out? Doesn’t the VSC Low pressure output come out? 2. Check the Interface signal 1.
Page 17
2. VSC Board 2-1. No Power (1) Symptom 1) Minute discharge doesn’t occur at module. 2) Front LED doesn’t come into action (2) Check follow Is the Power Cord Plug in Power Cord plug in ? Is the Line Filter and PSU Connect Cable (SC100) connected? Is the...
Page 18
2-2. No Raster - LCD (1) Symptom 1) Does’t minute discharge at module. 2) It maintains the condition where the front LED is normal. (2) Check follow 'Inverter_On' Is the inverter Is the Inverter Signal is High of 5 Check the Power board. 24V on power board On or Off in P1000 on Main...
Page 19
2-3. In case of occur strange screen into specific mode 2-3-1. In case of doesn’t display the OSD (1) Symptom 1) LED is White 2) The minute discharge work continuously (2) Check follow Is the LVDS Is the LVDS cable Replace cable.
Page 20
2-3-2. In the case of doesn't work normally at specific input mode (1) Symptom - The screen doesn't work normally at specific input mode (RF, AV, Component, RGB, HDMI) (2) Check follow 1) Check the all input model if all input display normally. 2) Check the PIP and Double Window if it display normally.(Re-Check it Swap) (3) In case of unusual situation from RF mode Is normal...
(5) When set doesn't display normally at Component, RGB mode Is the Input voltage, IIC Is the IC800 Replace IC800. Communication and HV normal? sync normal? (6) In the case of becomes unusual display from HDMI mode Is the Input voltage, IIC Is the IC1200 Replace IC1200.
Need help?
Do you have a question about the 32HIZ22 and is the answer not in the manual?
Questions and answers