Contents I. Appearance of Equipment………………………………………………………………..2 II. Wiring of Equipment………………………………………………………………..2-3 III. Illustration of Remote Control………………………………………………………..3 IV. Product Introduction………………………….……………………………….…..4 4.1 Features 4.2 Spec cation 4.3 Performance parameters 4.4 Accessories V. Functions and Basic Operations……………………………………………………..5 5.1 Compatibility of product 5. 2 Introductions iPad / iPhone / iPod touch VI.
I. Appearance of Equipment Front View Rear View 1. iPhone / iPad / iPod touch 30 pin connector 2. Adjustable slide (applicable erent models) 3. Receiver 4. Standby Buttons with LED (LED status: blue is power on, red is standby) 5.
Connected via YPbPr Cable & Audio L/R cable Note: If your equipment is properly connected with the DOCK, the Apple device screen will show this icon ( , see page 5), but there is no output on the TV until the Apple device entering into Photo/Audio/Video play status.
IV. Product Introduction 4.1 Features 1. Compatible with iPod Touch, iPhone and iPad. 2. Allow local videos of compatible models and the online video to play on TV, and support up to 720p video output. 3. Allow local music of compatible models and the Internet music to be output to TV or stereo system.
V. Functions and Basic Operations 5.1 Compatibility of Product Compatible iPod touch models Compatible iPhone models 5.2 Basic Operations of iPad / iPhone / iPod touch If your equipment is properly connected with the DOCK, the screen will show the icon as below. - 5 -...
VI. Music / network music playback instructions 6.1 Online music playback method: 1. For use on iPhone / iPod Touch a. Connect the HDMI dock to the TV with an HDMI cable. Make sure the TV’s input is set to HDMI. (Figure 1) Switch on the main power switch at the back of the unit beside the HDMI port.
Page 8
2. For use on iPad (Figure 5) (Figure 6) NOTICE: iPad has limited controls via remote due to software restrictions. 6.2 Network music playback method: 1. Click to turn launch Safari browser. Input the music web address and open the playlist to select the music (its smoothness depends on network transmission speed, if not fluent, you can replay it after suspended buffer.) NOTICE: After the network music starts playing, Standby/VOL-/VOL+/Mute button is active.
VII. Video/ network Video playback instructions: 7.1 Video playback can be selected by the following method: 1. For use on iPhone / iPod Touch Click and select the video program to play back. (Figure 9) (Figure 10) NOTICE: a. MENU button on the remote only applies to iPhone & iPod Touch. When the iPhone’s screen is on the video selection menu (Figure 9), the MENU Button can be used to select the Video list.
b. Remote control can be used after the network video starts playing. Standby/VOL+/VOL-/Play/Pause/Mute button is supported. 7.2 Network video playback method: Click the , turn to launch the video playlists. Choose your desired video. (Figure 14) (Figure 15) (Figure 16) NOTICE: Smoothness of the video depends on the network transmission speed, if not fluent, you can replay it after suspended buffer.
(Figure 19) IX. Safety Notices 1. Follow all instructions. 2. Do not place this device near water. 3. Do not place near heat sources such as radiators, heat registers, stove, or devices(including amplifiers) that produce heat. 4. Unplug power adapter during lightning storms or when unused for long periods of time. 5.
Page 12
When HDMI cable and YPbPr cable are both connected, the default is “HDMI” output. You can shift the output by pressing the button “HD/YUV” on the remote control. If video or subtitle displayed is unusual, please set the screen mode of TV or the wide screen settings of video output of the compatible models.
Need help?
Do you have a question about the MLG-6025DK and is the answer not in the manual?
Questions and answers