Advertisement
4.If the batteries in the device are consumed or the device is not to be used for a long period
of time, remove the batteries to prevent damage or injury from possible battery leakage.
5.Do not try to recharge the battery not intended to be recharged; it can overheat and
rupture. (Follow battery manufacturer's instructions.)
6.Do not dispose of battery in fire. Battery may explodes or leak.
7.Clean the battery contacts and also those of the device prior to battery installation.
AC/DC Adaptor:
1. Insert the DC Plug from the supplied AC/DC Adaptor to the DC IN Jack on the rear of unit.
2. Insert the AC/DC Adaptor into wall outlet having AC 100-240V~, 50/60Hz
NOTES:
~ When AC/DC Adaptor was connected, the battery power will cut off automatically.
~ This AC/DC Adaptor is intended to be correctly orientated in a vertical or floor mount position.
~ When connected the iPod/iPhone to the docking, it will be charging automatically.
~ If Apparatus will not be used in a long period of time. To avoid damage the the unit. Unplug
the AC/DC Adaptor from the wall outlet and take out all batteries.
OPERATION
To set or reset the actual time:
1.Make sure the unit is in power off (standby) mode before setting.
2.Press and hold the MEM/SET Button on the front of unit until the digit of hour on
the display is blinking. Press the
PM Indicator on the display is lit if the time is PM and not light if the time is AM).
3.Press the MEM/SET Button again; the digit of minute on the display will blink.
Press the
or
Button to set the Minute.
4.When finished, press the MEM/SET Button to save the settings and exit.
TIME SYNCHRONIZATION
The CMB3228 features a "CH MODE" button that allows you to set the time using the
internal clock of the iPod/iPhone.
With the iPod/iPhone docked and power OFF, press the "CH MODE" button once.
NOTE:
When you first dock your iPod/iPhone, the unit will run an authentication process,
so it may not respond immediately to the "CH MODE" button when pressed. Wait
for a few seconds and try pressing the "CH MODE" button again.
An iPod/iPhone can only sync time up to the nearest minute; it's possible to have up
to 59 seconds difference between the unit and synced iPod/iPhone.
The iPod internal clock is automatically updated when sync'd with iTunes. We
recommend you sync the iPod with iTunes prior to docking to CMB3228 to make
sure you have the current time available.
The iPhone receives constant updates from the phone service provider, so the
iPhone time will always be current.
The sync function can only be done when the CMB3228 power is Off.
3.Press the POWER/FUNC Button to turn on the unit.
4.Press the POWER/FUNC Button repeatedly until "IPod" appears on the display.
5.Press the >ll Button to start playback.
6.During playback:
A.Press VOL+/AL 1 or VOL–/AL 2 Button to adjust volume level as desired.
B.Press the
Button to pause. Press again to resume normal playback.
C.Press the
or
Button to skipping tracks.
D.Press and hold the
or
Button to fast searching the desiredd section of current tracks.
7.To power off (Standby mode) the unit, press and hold the POWER/FUNC Button until OFF
appear on the display, then release the button.
Note: If you have an earlier non-dockable iPod , connect it to the AUX IN jack as the AUX IN
section follows.
AUX IN
To listen to the music from the external audio device or non-dockable iPods as follows:
1.Connect the external audio device or iPods/iPhone by an audio connection cable with 3.5mm
stereo plug on both ends (Cable not included).
2.Insert one end to the AUX Jack on the rear of unit. Insert the other end to the Phones Jack;
Line Out Jack or AUX Out Jack on the external audio device or iPods.
3.Press the POWER/FUNC Button to turn on the unit.
4.Press the POWER/FUNC Button repeatedly until "AU" appears on the display.
5.Playback the music in the connected external audio device or iPods as usual.
6.Press VOL+ or VOL– Button on the unit (and the connected unit) to adjust volume level as
desired.
7.To power off (Standby mode) the unit, press and hold the POWER/FUNC Button until OFF
appear on the display then, release the button.
ALARM SETTING
Alarm 1 setting:
1.Make sure the unit is in power off (standby) mode before setting.
2.Press and hold the VOL +/AL 1 Button for one second to enter setting mode. The AL 1
Indicator will light and Alarm 1 time will appear on the display (The digit of hour will be
blinking).
3.Press the
or
Buttons repeatedly to set the hour. (Make sure the PM Indicator on the
display is light if the alarm 1 time is PM and not light if it is AM).
4.Press the VOL +/AL 1 Button again, the digit of minute will be blinking. Press the
Buttons repeatedly to set the minute.
5.Press the
or
Buttons repeatedly to set the wake up mode to buzz (b), Radio (F) or
iPod/iPhone (I).
6.Press the VOL +/AL 1 Button to enter, the volume level (two digits) will appear on the display.
Press the
or
Buttons to set the volume level as desired.
7.Press the VOL +/AL 1 Button to save the settings and exit.
Alarm 2 setting:
Same as Alarm 1 settings above. But, press the VOL -/AL 2 Button instead of press the VOL
+/AL 1 Button.
or
Button to set the hour. (Make sure the
Radio reception
1.Press the POWER/FUNC Button to turn on the unit.
2.Press the POWER/FUNC Button repeatedly until Radio frequency appears on the display. Wait a
few seconds, you will hear sounds from speakers.
3.Press and hold the
the button. (When a radio station was been found, the frequency on display will stop running and
start to playback the searched station.) Press and release the
if needed.
4.Repeat procedure 2 until the desiredd radio station was found.
5.Adjust the volume to the desiredd level by pressing VOL+/AL 1 or VOL–/AL 2 Button.
6.To power off (Standby mode) the unit, press and hold the POWER/FUNC Button until OFF
appear on the display then release the button.
ANTENNAS:
The Antenna wire on the rear cabinet is for radio reception. If reception is weak, unwind and
extend the wire or relocate the wire to improve the radio reception.
RADIO STATION PRESETTING
1.Receive the desiredd radio station as the previous procedure.
2.Press the MEM/SET Button, "P XX" (XX is the last stored number of radio station) will appear on
the display and "XX" will be blinking. Press the
desiredd location (CH 1 – CH 20) you want store to. Press the MEM/SET Button again to store.
3.Repeat the same procedure until all the desiredd radio stations were stored into the memory.
4.After settings, press the CH MODE Button to enter to Channel mode. "P XX" will appear on the
display. Press the
Notes:
If AC/DC Adaptor has been unplugged from the wall outlet or the power supply failed, the preset
radio stations will be deleted.
The stored radio station only can be deleted by storing another new radio station.
Total 20 radio stations can be stored in the memory list.
In Radio mode, only the frequency of current radio station will appear on the display.
To view current time. Press Standby Button to power off the unit.
Docking and Charging The iPod/iPhone:
This unit is designed with the same connector found in most iPod and iPhone docks. When
connecting the supported iPod/iPhone to the docking station on the top of the unit. The connecting
iPod/iPhone will be start recharging. You can also playback the music files in the iPod/iPhone as
follows:
1.Remove the cover of the iPod/iPhone Docking as shown on the figure below:
2.Insert the iPod/iPhone to the docking as shown below (If the power source of the unit is AC/DC
Adaptor. When iPod/iPhone is inserted, it will recharge automatically) :
IMPORTANT NOTE:
Alarm will not operate when the unit is in power on mode.
If radio (F) was select, select the desired radio station as previous procedure before
activating alarm.
If iPod/iPhone mode was selected, make sure the iPod/iPhone was inserted in the
docking properly.
SHUT OFF ALARM:
When alarm goes off, press POWER/FUNC Button to turn it off , the alarm will
reset for next day.
To turn off the alarm completely (not reset for next day). Press the VOL +/AL 1 (VOL -/AL
2 Button), the AL 1 (AL 2) Indicator will turn off.
SNOOZE
The alarm can be temporarily turned off manually by pressing the
SNOOZE/SLEEP/DIMMER Button; the alarm will turn back on automatically nine (9)
minutes later. This feature can be repeated until POWER/FUNC Button was pressed.
SLEEP
In the power on mode, press the SLEEP Button to activate the sleep function, SLEEP time
will appear on the display. Press the SLEEP Button repeatedly to set the sleep timer to 10 –
90 minutes as desired.
To turn off the unit before sleep timer time up, press and hold the POWER/FUNC Button
until "OFF" appear on the display.
Protect Your Furniture:
This model is equipped with non-skid rubber 'feet' to prevent the product from moving when
you operate the controls. These 'feet' are made from non-migrating rubber material
specially formulated to avoid leaving any marks or stains on your furniture. However certain
types of oil based furniture polishes, wood preservatives, or cleaning sprays may cause the
rubber 'feet' to soften, and leave marks or a rubber residue on the furniture. To prevent any
damage to your furniture we strongly recommend that you purchase small self-adhesive felt
pads, available at hardware stores and home improvement centers everywhere, and apply
or
these pads to the bottom of the rubber 'feet' before you place the product on fine wooden
furniture.
or
Button until the displayed frequency starts running then release
or
Button repeatedly to select the
or
Buttons repeatedly to select the desiredd stored radio station.
Meijer.com
or
repeatedly to fine tune
Hide quick links:
Advertisement
