Hdmi: Frequently Asked Questions - Rotel RSP-1580 Owner's Manual

English
Video and Audio do not match .
• Check that the proper video source is selected for each input.
• Check that the group delay (lip-synch) setting is not misadjusted.
Clicking or popping sounds when switching inputs
• The unit uses relay switching to preserve maximum sound quality.
The mechanical clicking of the relays is normal.
• During switching, it may take a split second for digital signals to
be recognized and properly decoded. Rapid repeated switching
between inputs or settings can result in clicks or pops from the
speakers as the unit attempts to lock on to the rapidly changing
signals. This causes no harm.
Controls do not operate
• Make sure that fresh batteries are installed in the remote.
• Make sure that the IR sensor on the front panel is not blocked. Aim
he remote at the sensor.
• Make sure the sensor is not receiving strong IR light (sunlight,
halogen lighting, etc.)
• Unplug the unit from the AC outlet, wait 30 seconds, and plug it
back to reset.
No video from MON 2, 3 or 4
• Check MON SETUP configuration and MON video input setting
assigned and make sure that a video source is connected.

HDMI: Frequently Asked Questions

What is HDMI?
HDMI (High-Definition Multimedia Interface) is an advanced type of
connection which carries both video and audio in a single cable. It is a
modern digital replacement for older analog video connection standards
such as Composite Video, S-Video and Component Video. This Rotel unit
meets the latest version of HDMI specification, HDMI 1.3, and HDMI
1.4a with 3D support.
What is the difference between HDMi and DVI?
An earlier digital connection standard, DVI (Digital Visual Interface) can
also be used for high-definition video signals by means of a suitable
adaptor. However, unlike HDMI, the DVI connection does not also
carry audio signals, nor does it automatically set the picture screen to
the correct size.
What is the difference between HDMI 1 .4, HDMI 1 .3 and earlier
versions?
If you have a Blu-ray player, note that the HDMI 1.3 connection can
carry the new Dolby TrueHD and DTS HD Master Audio formats used
on Blu-ray discs. This processor is able to decode and replay these 7.1
channel audio formats. HDMI 1.4 includes additional features such as
3D video pass through for movies, games and broadcasts.
Also with Blu-ray, but depending on the monitor being used to view the
picture, you may also be able to enjoy video enhancements such as Deep
Color or XY video (also called Broad Color Space). Using the HDMI 1.4
connection, the RSP-1580 can pass these signals through from the Blu-ray
player to a compatible monitor.
These new audio formats and video features are not available from standard
DVD discs or players, even when an HDMI connection is used.
Can I connect components which have earlier versions of HDMI?
Yes, because HDMI is backwards-compatible. This means that components
which have earlier versions of HDMI (such as HDMI 1.1 or HDMI 1.2)
will perform correctly when connected to the HDMI 1.4 inputs or outputs
of the unit.
If your DVD player is equipped with HDMI 1.2a, the HDMI connection
will permit the transmission of 1080p (high definition) video signals.
Which is the best way to rescale the picture?
When using legacy components that require picture rescaling, it is better
to use the monitor scaler to handle any picture resizing. You should try
to use only one scaler in the system, so keep your DVD player set to
480p or 1080p. A 480p signal will be rescaled by the monitor and
a 1080p signal will be seen by a monitor with 1080p resolution as a
native signal.
Some Blu-ray and HD-DVD discs have been recorded in 1080i. These
should not be scaled, but are best left to the monitor to interpret into an
appropriate format for the screen.
Will the HDMI digital output improve the picture quality from old
analog sources?
Analog picture sources from legacy units begin by being less good than
digital signals, and while the RSP-1580 will translate them into a digital
format, the final quality will be constrained by the original source, and
the choice of connection (Composite, S-Video or Component). The scaler
cannot correct for low resolution signals and will not improve inherently
poor picture quality.
Why does the HDMI connection sometimes not give a picture?
Although it is simple to use, the HDMI connection is actually a highly
complex electrical circuit, and within it is a security system called HDCP
(High Definition Content Protection). In some circumstances pictures
may not reproduce, or may not reproduce properly, due to the action of
DRM (Digital Rights Management) or the 'handshake' between the two
connected units. HDMI cables contain circuits that exchange a 'handshake'
signal several times a second, designed to maintain the integrity of the
transmission signal and to prevent attempted unauthorized copying of
copyright material. However, these 'handshake' signals can be disrupted
for several reasons. If problems persist, consult your Rotel dealer.
43