Table of Contents
Advertisement
Quick Links
�
� � � ��� � � � � � � � � � �
� � � ��� � � � � � � � � � �
� � � ��� � � � � � � � � � �
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
����������������� ����������
����������������� ����������
������������������
������������������
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
����������������������������������������������������������������������������������������������
���������������������������������������������������������������������� � ����� ���� ���� � ��������
�
����������������
������������������� ����
������������������������
Advertisement
Table of Contents
Summary of Contents for Mutec Smart merge
- Page 1 � � � � ��� � � � � � � � � � � � � � ��� � � � � � � � � � � � � � ��� � � � � � � � � � � �...
-
Page 3: Safety Instructions
§1 Warranty MUTEC GmbH warrants the flawless performance of this product to the original buyer for a period of two (2) years from the date of purchase. If any failure occurs within the specified warranty period that is caused by defects in material and/or workmanship, MUTEC GmbH shall either repair or replace the product free of charge within 30 days. -
Page 4: Table Of Contents
SMART MERGE front panel ......SMART MERGE rear panel ...... -
Page 5: Features
If no Word Clock is available, the reference can be extracted from the digital inputs. Unique to the SMART MERGE is to process highest digital input levels without any manual leveling! The powerful 32bits-floating-point... -
Page 6: Control Elements And Connections
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � CONTROL ELEMENTS AND CONNECTIONS SMART MERGE front panel 1 POWER This red LED lights up when the device is turned on using the main switch at the rear (POWER) and the country-specific mains voltage is supplied. - Page 7 This input receives a Word Clock or Word Clock x 256 clock signal (known as Super Clock for ProTools systems) to synchronize the SMART MERGE. 6 230V (115V) The mains voltage fuses are located behind this shutter. These must be...
-
Page 8: Installation
Proceed as described in the appendix under »Disabling the termination«. If the SMART MERGE Word Clock output is used to synchronize other You should generally avoid »daisy chaining« Word Clock lines using passive BNC T devices, ensure that the Word Clock inputs of the connected devices are properly terminated, except in the case of a daisy chain. -
Page 9: Operation
Connecting the devices Signal Inputs When selecting which of the SMART MERGE digital audio inputs to use to connect the devices please note that there are two interfaces available for each of inputs 1 + 2. Input 1 enables the connection of a S/PDIF or AES/EBU signal source whereby switching between the two connections is automatic. -
Page 10: Monitor Function
Monitor-Status-LEDs In addition to individual listening, the monitor function integrated in the SMART MERGE also enables the patching of the individual input signals on the AES/EBU master output. Both of these functions are selected using the SINGLE / MASTER switch. -
Page 11: Set-Up Example
These get synchronized through the inputs of SMART MERGE. A separate Word Clock generator, here MUTEC’s SMART CLOCK av, is synchronizing the SMART MERGE which feeds in his mix signal into the mixing desk. Thus the asynchronous output signals of the musical instruments are integrated into the synchronous studio set-up. -
Page 12: Appendix
������������ �� � � � � � � �� � � � � � � �� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � APPENDIX Pin assignment of the connectors Mains... -
Page 13: Technical Data
������������ �� � � � � � � �� � � � � � � �� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � Technical data S/PDIF INPUTS 4 x coaxial (Cinch/RCA), unbalanced, input impedance 75 Ω, 200mV –... - Page 14 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �...
Need help?
Do you have a question about the Smart merge and is the answer not in the manual?
Questions and answers