Advertisement
HAWF2046-U_07EM1.qxd
12/10/07
14:49
Page 2
P L E A S E R E A D A N D S AV E T H E S E
I M P O R TA N T S A F E T Y I N S T R U C T I O N S
When using electrical appliances, basic safety precautions
11. The use of attachments not recommended or sold by
should always be taken including the following:
the appliance manufacturer may cause hazards.
12. DO NOT use outdoors.
1. Read all instructions before using this appliance.
13. DO NOT let the cord hang over the edge of a table,
2. Use fan only for purposes described in the instruction
counter or come in contact with hot surfaces or leave
manual.
exposed to high traffic areas.
3. To protect against electrical shock do not immerse
14. To disconnect, grip plug and pull from wall outlet.
unit, plug or cord in water or spray with liquids. Plug
Never yank on cord.
the appliance directly into a 120V AC electrical outlet.
15. Always use on a dry, level surface.
4. WARNING: To reduce the risk of fire or electrical
16. DO NOT operate fan until fully assembled with all
shock, DO NOT use this fan with any solid-state speed
parts properly in place.
control device.
17. This product is intended for household use only and
5. Close supervision is necessary when any appliance is
not for commercial or industrial applications.
used by or near children.
6. Unplug from outlet when not in use, when moving
fan from one location to another, before putting on
or taking off parts and before cleaning.
7. Avoid contact with moving parts.
PLEASE READ AND SAVE
8. DO NOT operate in the presence of explosives and/or
flammable fumes.
THESE IMPORTANT SAFETY
9. To avoid fire hazard, NEVER place the cord under
rugs or any parts near an open flame, cooking or
INSTRUCTIONS
other heating appliance.
10. DO NOT operate any appliance with a damaged cord
or plug after the appliance malfunctions, or has been
dropped/damaged in any manner.
THIS APPLIANCE HAS A POLARIZED PLUG (one blade is wider than the
other). To reduce the risk of electric shock, this plug is intended to fit in
a polarized outlet only one way. If the plug does not fit fully in the
outlet, reverse the plug. If it still does not fit, contact a qualified
electrician to install the proper outlet.
DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS
SAFETY FEATURE IN ANY WAY.
F E AT U R E S - O P E R AT I O N S
C L E A N I N G / M A I N T E N A N C E
• To pull in fresh air from the outside, slide both Air
WINDOW FAN INSTALLATION
Flow Switches (A) to the Intake position.
Your window fan is designed to be used with a window
• To exhaust the inside air out, slide both Air Flow
screen in place. To install your window fan, simply
Switches to the Exhaust position.
position your fan on the edge of the window sill and close
• To circulate fresh air into your home and stale air out,
the window sash so that the window rests in the track on
slide one of the Air Flow Switches to the Intake position
the top of the fan.
and the other Air Flow Switch to the Exhaust position.
OPERATING INSTRUCTIONS
COMFORT CONTROL THERMOSTAT
Plug the fan into a 120V AC electrical outlet.
Your fan is equipped with a Comfort Control Thermostat
Fan speed control settings = Off, High, Med, Low.
that you can program to turn the fan ON and OFF
automatically.
Electrically Reversible Air Flow: Your fan blades are
electrically reversible so that you can change the direction
• Plug the fan into a 120V AC electrical outlet.
• For the fan to turn ON automatically, you must set
of the air flow by sliding the switches.
the thermostat to a temperature higher than the
Fig. 1 Front View
A
current room temperature. If the fan power is on but
B
A
C
D
the fan blade(s) aren't moving, turn the Comfort
D
E
Control Thermostat dial to the right until the fan
blade(s) spin.
• To set your desired comfort level, run the fan until
the temperature in your room is comfortable. Slowly
turn the Comfort Control Thermostat dial to the left
until the fan blades turn off. Your fan will maintain
this temperature.
IMPORTANT: If you want your fan to run continuously,
turn the Comfort Control Thermostat dial all the way to
C. Fan Speed Control
A. Air Flow Switches (2)
the right.
D. Fan Grills (2)
B. Comfort Control
Thermostat Knob
E. Front Housing
CLEANING/MAINTENANCE
INSTRUCTIONS
H
F
Fig. 2 Rear View
H
Follow these instructions to correctly and safely care for
your fan.
• Always unplug the fan before cleaning or
disassembling.
• Be sure to clean your fan with a soft cloth moistened
with a mild soap solution.
• Do not allow water to drip on or enter into the fan
housing.
• Do not use gasoline, thinner, or benzene as a cleaner.
• Lightly run a vacuum cleaner nozzle over the fan
grill to remove any dust or dirt that may have
F. Grill Release Button
H. Removable Fan Grills (2)
accumulated.
G. Fan Blade (not shown)
C L E A N I N G / M A I N T E N A N C E
T R O U B L E S H O O T I N G
Fan Blade Cleaning
Fig. 3
• Unplug the fan and remove the fan from the window.
• While pressing the grill release button, turn the
H
removable fan grills counter-clockwise (see Fig. 3).
• Remove the grills (see Fig. 4).
• Use a soft cloth moistened with a mild soap solution
to clean the fan blades (see Fig. 5).
F
• Place the grills back onto the fan and turn them
clockwise until they click into place. Make sure the
grills are secured, prior to replacing the fan in your
Fig. 4
window and beginning operation.
FAN STORAGE
• Store your fan in the original box or an appropriately
sized box.
• Protect the fan head from dust.
• Store your fan in a dry location.
Fig. 5
If you have any questions regarding your product or
would like to learn more about other Holmes
®
products,
please contact our Consumer Service Department at
G
1-800-546-5637 or visit our website at
www.holmesproducts.com
TROUBLESHOOTING GUIDE
Issue
Potential Cause
Potential Solution
Air does not seem to be
Air Flow Switches set to
Adjust Air Flow Switches to Intake.
blowing in properly.
Exhaust rather than Intake.
Fan will not operate even
Fan is not plugged in.
Plug in the power cord into a 120 V AC Outlet. Be sure
though I am turning the Fan
the Speed Control knob is in the off position prior to
Speed Control knob.
plugging in the Fan.
Fan is not secure in the
Fan may not be set in the
Ensure that the bottom edge of the window sash fits
window and moves during
window properly.
securely into the groove along the top of the Fan. Close
operation.
the sash completely on top of the window so it is secure.
Please refer to the Installation portion of the manual for
more details.
Advertisement
