Advertisement
HASF1603_07EM1.qxd
10/18/07
10:20 AM
Page 2
P L E A S E R E A D A N D S AV E T H E S E
I M P O R TA N T S A F E T Y I N S T R U C T I O N S
When using electrical appliances, basic safety precautions
15. Always use on a dry, level surface.
should always be taken including the following:
16. Do not operate fan until fully assembled with all
parts properly in place.
1. Read all instructions before using this appliance.
17. This product is intended for household use ONLY and
2. Use fan only for purposes described in the instruction
not for commercial or industrial applications.
manual.
18. WARNING: To reduce the risk of electrical shock
3. To protect against electrical shock do not immerse
and injury to persons, DO NOT use your fan in the
unit, plug or cord in water or spray with liquids and
window.
plug the appliance directly into a electrical outlet.
4. WARNING: To reduce the risk of fire or electrical
shock, DO NOT use this fan with any solid-state speed
PLEASE READ AND SAVE
control device.
5. Close supervision is necessary when any appliance is
THESE IMPORTANT SAFETY
used by or near children.
INSTRUCTIONS
6. Unplug from outlet when not in use, when moving
fan from one location to another, before putting on
or taking off parts and before cleaning.
7. Avoid contact with moving parts.
ASSEMBLY INSTRUCTIONS
8. Do not operate in the presence of explosive and/or
Tools required: One Phillips head screw driver.
flammable fumes.
Assembly time: 10-15 minutes.
9. To avoid fire hazard, NEVER place the cord under
rugs or any parts near an open flame, cooking or
NOTE: MAKE SURE YOU REMOVE ALL CONTENTS OF THE
PACKAGE. PLEASE CHECK PACKAGING MATERIALS FOR
other heating appliance.
10. Do not operate any appliance with a damaged cord
PARTS THAT COULD BE REQUIRED TO ASSEMBLE YOUR
or plug after the appliance malfunctions, or has been
FAN.
dropped/damaged in any manner.
1. Remove the base weight and nut from the bottom of
11. The use of attachments not recommended or sold by
the fan base. Unscrew the nut and remove the
the appliance manufacturer may cause hazards.
plastic plug from the hole of the base to
12. Do not use outdoors.
remove the base weight.
13. Do not let the cord hang over the edge of a table,
2. Insert Lower Pole through the hole in the center of
counter or come in contact with hot surfaces or leave
Base and twist clockwise into position. Be sure to
exposed to high traffic areas.
align the grooves on the threaded joint with the
14. To disconnect, grip plug and pull from wall outlet.
raised slots protruding from the base center walls.
Never yank on cord.
(See Figure 1)
THIS APPLIANCE HAS A POLARIZED PLUG (one blade is wider than the
other). To reduce the risk of electric shock, this plug is intended to fit in
a polarized outlet only one way. If the plug does not fit fully in the
outlet, reverse the plug. If it still does not fit, contact a qualified
electrician to install the proper outlet.
DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS
SAFETY FEATURE IN ANY WAY.
F E AT U R E S - O P E R AT I O N S
3. Turn the Base upside down (pole facing the floor)
Figure 1
G H I
F
E
C
D
and place the Weight over the threaded pole end.
A B
The threads will be exposed as they protrude through
J
the weight.
4. Secure the Weight to the Base by tightening the
K
Weight Nut in a clockwise direction.
L
NOTE: DO NOT use a tool to tighten the Base Nut.
5. Insert the remaining Pole with the Threaded Joint
into the Hollow End of the Pole connected to the Base
N
M
and twist clockwise to secure.
O
6. Place Motor Housing assembly onto the Upper Pole.
7. Position the Rear Grill over the Motor Shaft, making
P
certain the 2 notches at the top and bottom of the
A. Logo Plate
Rear Grill fit over the 2 prongs on the Motor
Q
B. Front Grill
Housing. Secure the Rear Grill in place with the Rear
C. Blade Cap
Grill Mounting Nut. Turn Mounting Nut clockwise and
R
D. Fan Blade
tighten firmly.
E. Rear Grill Mounting
8. Slide the Fan Blade, with the hollowed interior of the
S
Nut
Blade facing toward the Rear Grill, firmly onto the
F. Rear Grill
Motor Shaft. Secure the Fan Blade onto the Motor
T
G. Motor Shaft
Shaft by turning the Blade Cap counter-clockwise and
H. Motor Housing
tighten firmly.
Assembly
9. Center the Front Grill by aligning the Holmes
I. Oscillation Knob
horizontally and parallel to the floor, and then place
J. Speed Control Knob
into the Rear Grill. Snap the Front and Rear Grills
K. Grill Mount
completely together. Tighten the Grill Screw at the
L. Tilt-Adjustment Knob
bottom of the Rear Grill.
M. Upper Pole
10. Insert Decorative Oscillation Cap into Oscillation Knob
N. Grill Screw
located on top of Motor Housing Assembly. Refer to
O. Threaded Joint
letter I in Figure 1 for placement.
R. Base
(Male)
NOTE: If Logo Plate is not already assembled to
S. Base Weight
P. Hollow End (Female)
Front Grill, you must attach it by aligning the slots
T. Weight Nut
Q. Lower Pole
located on the back side of the Logo Plate with the
notches in the grill center. Press firmly into place.
F E AT U R E S - O P E R AT I O N S
C L E A N I N G / M A I N T E N A N C E
OPERATING INSTRUCTIONS
CLEANING/MAINTENANCE
1. Set fan on a dry, level surface.
INSTRUCTIONS
2. Plug cord into any standard 120 volt AC outlet.
Follow these instructions to correctly and safely care for
Please make sure the Speed Control Knob is in the
your fan. Please remember:
off position.
• Always unplug the fan before cleaning.
3. Turn the Speed Control Knob located on the back of
• Do not allow water to drip on or enter into fan
the Motor Housing Assembly to select your desired
speed. O-Off, III=High, II=Medium, I=Low.
• Be sure to use a soft cloth moistened with a mild
OSCILLATION
The Oscillation control knob (
) is located on the top
• Do not use any of the following as a cleaner:
of the Fan Motor Housing. To start Oscillation, push
control knob down. To stop Oscillation, pull control knob
Fan Cleaning
up.
Clean the Fan Grill, Housing, Fan Blade and Base with a
soft, damp cloth. Please use caution around the Motor
ADJUSTMENT INSTRUCTIONS
Housing area. Do not allow the motor or other electrical
components to be exposed to water.
Fan Head Tilt-Adjustment
To access the blade, remove the front grill from the fan
1. To change the tilting angle of the Fan Head, simply
head. Clean the blade with a soft, damp cloth. Make sure
loosen the Tilt-Adjustment Knob.
that the front grill is secured to the fan head prior to
2. Move the Fan Head to the desired angle and firmly
beginning operation again.
tighten the Tilt-Adjustment Knob to lock into place.
logo
®
Reduced Height Adjustment
FAN STORAGE
3. Remove the Lower Extension Pole for reduced height.
When storing your fan in the off season, it is important
to keep it in a safe dry location. It is important to protect
the fan head from dust. We strongly recommend using
the original box from purchase.
housing.
soap solution.
gasoline, thinner, or benzene.
If you have any questions regarding your product or
would like to learn more about other Holmes
®
products, please contact our Consumer Service
Department at 1-800-546-5637 or visit our website at
www.holmesproducts.com
Advertisement
