Advertisement
F. Using Headphones/Earphones
Headphones / Earphones
Turn down the volume before connecting the
[1/8" (3.5mm) diameter plug]
headphones/earphones. Slowly raise the volume
with the headphones on until you reach your
desired volume. When headphones are connected,
the speaker is automatically disabled.
Warning:
Excessive sound pressure from earphones and
headphones can cause hearing loss. Avoid
listening to sound at excessive levels which could
be harmful to your ears.
DVD player
Monitor
right side
left side
Installing in a Vehicle
Mounting in the Vehicle
Use the supplied mounting straps to install the DVD player and monitor on the back of the vehicle's headrests.
Tightly wrap the mounting strap around the headrest.
Mounting the DVD Player
Mounting the Monitor
Installation Guide
SAFETY WARNING!
• This unit should never be used by the vehicle's driver or left unsecured in the vehicle while driving.
• If this unit is being used in your vehicle, be sure that it is secured or held safely, and does not obstruct any safety
device, including air bags or seat belts.
• All passengers should wear seat belts when using this unit in a moving vehicle.
• If in doubt, please contact your vehicle manufacturer for further advice.
Using the Stand for Desktop Use
Unit Operation
You can stand the DVD Player and monitor up on a
Turning on the Unit
desk or table using the stand on the back.
1. Slide the STANDBY / ON switch on the DVD player
to the ON position. Slide the ON / OFF switch on the
monitor to the ON position.
2. The start-up picture will appear on the screens.
3. After use, slide the STANDBY / ON switch on the
DVD player to STANDBY (power off ). Slide the ON
/ OFF switch on the monitor to the OFF position.
E - 6
Playing a Disc
DVD
This owner's manual explains the basic instructions for operating this unit. Some DVDs are produced in
a manner that allows specific or limited operation during playback. Therefore, this unit may not respond
to all operating commands. THIS IS NOT A DEFECT. Please refer to the instructions accompanying the
specific DVD in question for more information about the options available on that DVD.
"
" may appear on the screen during operation. A "
" means that the desired operation is not
permitted by the unit or disc.
Playing a Disc
1. Slide the STANDBY / ON switch on the top of the unit to the ON position. (Slide the ON/OFF switch on the
monitor to the ON position.)
See
CUSTOMIZING THE FUNCTION SETTINGS
before proceeding to step 2.
2. Press the
button and hold the front panel to open the disc door.
3. Hold the disc by its edge and gently push it onto the spindle, with the label side facing the front, until you hear a "click".
4. Push the disc door gently to close it. It takes a short while for your unit to load the disc. After loading, for most
DVDs, the unit will automatically take you main menu or start playing. If the unit does not automatically start
playing the DVD, press the
PLAY button.
Pausing Playback (Still Mode)
Press the
PAUSE button. To resume normal playback, press the
PLAY button.
Each time you press the
PAUSE button, the picture advances one frame on a DVD.
Stopping Playback
Press the
STOP button at the location where you want to interrupt playback. To resume playback at the position
where the disc was stopped, press the
PLAY button.
If you press the
STOP button twice, the unit's memory will be cleared and pressing the
PLAY button will reset
the disc to the beginning.
Fast Forward / Fast Reverse
1. Press the SEARCH
or
SEARCH button when a disc is playing. Each time you press the SEARCH
or
SEARCH button, the playback speed changes in the following sequence:
2. Press the
PLAY button when you reach the desired point to resume normal playback.
Skip (Forward / Reverse)
• Press the
NEXT button to advance titles/chapters/tracks.
• Press the
PREV button to go back to current or previous titles/chapters/tracks.
• For Audio CDs, use the number buttons on the remote control to jump directly to the desired track.
Audio Selection
On some DVDs, the sound is recorded in two or more formats.
1. While a disc is playing, press the AUDIO button to show the current
audio format number.
2. Press the AUDIO button repeatedly to select the desired audio format.
Notes:
• If only one audio format is recorded on the DVD, the number does not change.
• About two seconds later, playback continues in the new audio format.
Subtitle selection
DVD
1. While a DVD is playing, press the SUBTITLE button to display the current language
setting, as shown in the example.
2. Press the SUBTITLE button repeatedly to select the desired subtitle language.
Notes:
• If only one language is recorded, the language does not change.
• About two seconds later, playback continues with the new subtitle you selected.
• The number of languages recorded differs depending on the disc.
• If no button is pressed within a few seconds, playback continues without changing the current subtitle.
• This function can only be used for discs on which subtitles have been recorded in multiple languages.
• On some DVDs, subtitles are activated from the main menu of the DVD. Press the MENU button to activate the
main menu.
Angle selection
DVD
Some DVDs contain scenes which have been shot from a number of different angles. For these discs, the same scene
can be viewed from each of these different angles.
1. While you are playing a DVD with different angles recorded,
press the ANGLE button to view the number of current angles
available.
2. Press the ANGLE button repeatedly to change the scene to the
next recorded angle.
• After approx. two seconds, playback will continue from the new
angle selected.
• If no button is pressed within 10 seconds, playback continues
without changing the current angle.
Notes:
• This function can only be used for discs on which scenes shot from multiple angles have been recorded.
• If only one angle is recorded, "
" is displayed.
Display function
DVD
While the disc is playing, press the DISPLAY button repeatedly to display information on operation status.
Repeat Playback
DVD
You can play a specific title or chapter repeatedly. (Title repeat, chapter repeat, A-B repeat)
Repeating a Chapter
DVD
1. While the DVD is playing, press the REPEAT DISC button until the "
" indicator displays on the screen.
The current chapter is played repeatedly.
Repeating a Title
2. While the DVD is playing, press the REPEAT DISC button until the "
" indicator displays on the screen.
The current title is played repeatedly.
To Resume Normal Playback
3. While the DVD is playing, press the REPEAT DISC button until the "
" indicator displays on the screen.
E - 7
Repeating a Single Track
1. While the CD disc is playing, press the REPEAT DISC button until the "
" indicator displays on the
screen. The current track is played repeatedly.
Repeating a Whole Disc
2. While the CD disc is playing, press the REPEAT DISC button until the "
" indicator displays on the screen.
The whole disc is played repeatedly.
To Resume Normal Playback
3. Press the REPEAT DISC button until the "
" indicator displays on the screen.
Repeating a Specific Section
DVD
You can play a specific section repeatedly.
1. While the disc is playing, press the REPEAT A-B button at the beginning of the section ("
" is displayed)
you want to play repeatedly.
2. Press the REPEAT A-B button again at the end of the section ("
" is displayed) you want to play repeatedly.
3. The unit will immediately begin replaying your selection.
To Resume Normal Playback
4. While the disc is playing, press the REPEAT A-B button until the "
" indicator displays on the screen.
Notes:
• A-B repeat can only be used within the same title. If the start and end of the section to be repeated are in different
titles, A-B repeat is cancelled.
• The A-B repeat function does not operate in scenes where different camera angles are recorded.
Locating a Desired Section
DVD
Locating a Specific Title
If a DVD contains title numbers, you can locate a specific title by directly selecting its title number.
1. Press the GOTO button.
2. Press the
or
button to highlight title number, press the corresponding
number buttons (2 digits) for the title you want. (For example: 02, 08, 10 or 15.) (If you press only 1 numeric
button, press the ENTER button to confirm.)
3. Playback starts from the selected title.
Locating a Specific Chapter
If you know the chapter number for the chapter that you want to play, you can locate it by directly selecting that number.
1. Press the GOTO button.
2. Press the corresponding number buttons (2 digits) for the chapter you want. (For
example: 02, 08, 10 or 15.) (If you press only 1 numeric button, press the ENTER button to confirm.)
3. Playback starts from the selected chapter.
Locating a Specific Time
You can move to a specific location by entering its corresponding time (hours, minutes, seconds).
1. Press the GOTO button two times.
2. Press the corresponding number buttons (5 digits: X:XX:XX, for example: 0 30 05, 1
08 23, 1 22 56.) for the setting point you want.
3. Playback starts from the selected section.
Notes:
• If the time entered is not permitted by the DVD, "
" will display. you should re-enter correct time.
• Some discs may not respond to this process.
• Some scenes may not be located as precisely as you specified.
• This method for accessing specific locations is available only within the current title of the DVD.
DVD Programmable Memory
DVD
You can combine your favorite titles/chapters and play them in the order you determine.
1. Press the MEMORY button while a DVD is playing. The following display appears.
Clear:
Delete all the input programs.
Exit:
Exit memory menu and return to normal playback.
Start:
Start memory playback.
Next / Prev: Move to the the next / previous setup page.
2. Input the title (2 digits) and chapter (2 digits) by pressing the number buttons. (For example: 01 02, 02 05, 02 11.)
It will move to the next item automatically.
• you can use the Cursor buttons ( , , , ) to move the highlighted bar to any item, and re-enter the title and
chapter. (Press the
NEXT /
PREV to move to the the next / previous setup page.)
• you can use the Cursor buttons ( , , , ) to move the highlighted bar to "Clear", "Exit", "Start" or "Next / Prev",
and press the ENTER button to confirm.
PLAY button to start memory playback. ("
3. Press the
" appears on the screen.)
4. To resume normal playback from memory playback
• Press the MEMORY button to display the memory menu.
• Use the Cursor buttons ( , , , ) to move the highlighted bar to "Stop". Press the ENTER button to confirm "Stop".
• Press the ENTER button to confirm "Exit". It will return to normal playback. ("
" disappear from the screen.)
Notes:
• If the title or chapter number entered is not permitted by the DVD, it will disappear. you should re-enter correct number.
• you should input items one by one following the 1, 2, 3 ... sequence.
• If the DVD contains only one title, you can only arrange order for chapters.
• Some discs may not permit memory playback operation.
• If you select repeat during memory playback, the DVD player repeats the current memory playback.
• If you press the MEMORY button while the display appears on the TV screen, the display disappears.
• The programmed selections will be cleared when you press the
STOP button two times, open the disc tray or
turn off the DVD player.
Viewing JPg Files
This unit can play JPg files recorded on a CD-R or CD-ROM disc (CD-RW is not recommendable).
1. Open the disc door.
2. Hold a JPg file disc by its edge and gently push it onto the spindle
with the label side facing up until you hear a "click".
3. Close the disc door. A list of folders/files will appear on the screen.
4. Press the
or
button to highlight a JPg file to play. Press the
PLAY button to start playback. Press the
STOP button to display a
folder list.
Notes:
• you can press the
PAUSE button to freeze the picture. Press the
PLAY button to resume picture slide show.
• you can press the
STOP button to quit playback.
• you can press the
PREV or
NEXT button to change the picture.
• you can press the ANGLE button on the remote control to rotate direction of the picture by 90°.
• Some discs may not permit this operation.
E - 8
Customizing the Function Settings
LANGUAGE SETUP
1. In STOP mode, press the SETUP button.
2. Press the
button to select Language Menu.
3. Use the
or
button to select the option (Player Menu,
Audio, Subtitle or Disc Menu), then press the button.
4. Use the
or
button to select your preferred language,
then press the ENTER button to confirm.
5. Repeat steps 3 and 4 to adjust other options. Press the
button to return to the previous menu.
6. To exit the SETUP MENU and return to the normal screen,
press the RETURN or SETUP button.
Notes:
• Some DVDs may not play in the audio language selected. A prior language may be programmed on the disc.
• Some DVDs may be set to display subtitles in a language other than the one selected. A prior subtitle language
may be programmed on the disc.
• Some DVDs allow you to change subtitle selections via the disc menu only. If this is the case, press the MENU
button and choose the appropriate subtitle from the selection on the disc menu.
• Some DVDs may not included your pre-selected language. In this case, the DVD player automatically displays disc
menus consistent with the disc's initial language setting.
VIDEO SETUP
1. In STOP mode, press the SETUP button.
2. Press the or button to select Video Menu.
3. Use the
or
button to select the option (Brightness or
Contrast), then press the button.
4. Use the
or
button to make adjustments, then press the
ENTER button. (The screen will change to your selected
setting).
5. Repeat steps 3 and 4 to adjust other options. Press the
button to return to the previous menu.
6. To exit the SETUP MENU and return to the normal screen,
press the RETURN or SETUP button.
SYSTEM SETUP
1. In STOP mode, press the SETUP button.
2. Press the or button to select System Menu.
3. Use the
or
button to select the option (TV Display or
Default), then press the button.
4. Use the
or
button to make adjustments, then press the
ENTER button. (The screen will change to your selected
setting).
5. Repeat steps 3 and 4 to adjust other options. Press the
button to return to the previous menu.
6. To exit the SETUP MENU and return to the normal screen,
press
the RETURN or SETUP button.
Cut off when a wide-screen
TV DISPLAY
video image is played
Pan Scan
• When wide-screen video is played, this mode clips the right and left
sides of the image so that it can be viewed on a conventional screen.
• Some wide-screen DVDs that do not permit Pan Scan mode playback
are automatically played in letterbox mode (black bands that appear
at the top and bottom of the screen).
Letter Box
• When wide-screen video is played in this mode on a conventional
Pan Scan
screen, black bands appear at the top and bottom of the screen.
Wide screen
• This is the correct mode for playing wide-screen videos on the unit or
other external wide-screens.
Notes:
• The displayable picture size is preset on the DVD. Therefore the
playback picture of some DVDs may not conform to the picture size
you select.
• When you play DVDs recorded in the 4:3 aspect ratio, the playback
Letter Box
picture will always appears in the 4:3 aspect ratio regardless of the TV
DISPLAY setting.
Default
It takes 3-5 seconds to reset the unit to the factory default.
Wide Screen
Maintenance
Cleaning the Disc
A defective or soiled disc inserted into the unit can cause sound to drop out during playback.
Handle the disc by holding its inner and outer edges.
• Do NOT touch the surface of the unlabeled side of the disc.
• Do NOT stick paper or tape on the surface.
• Do NOT expose the disc to direct sunlight or excessive heat.
• Clean the disc before playback. Wipe the disc from the center outward with a cleaning cloth.
• NEVER use solvents such as benzine or alcohol to clean the disc.
• Do NOT use irregular shaped discs (example: heart shaped, octagonal, etc.). They may cause malfunctions.
Cleaning the Unit
• Be sure to turn the unit off and disconnect the car power adapter before maintaining the unit.
• Wipe the unit with a dry soft cloth. If the surfaces are extremely dirty, wipe clean with a cloth that has been
dipped in a weak soap-and-water solution and wrung out thoroughly, then wipe with a dry cloth.
• Never use alcohol, benzine, thinner, cleaning fluid or other chemicals. Do NOT use compressed air to remove dust.
Important Note
• Before transporting the unit, remove any disc from the disc compartment.
Need More Help?
Please visit online help at http://www.RCAav.com
E - 9
Troubleshooting Guide
SYMPTOM
CAUSE (AND REMEDY)
No power.
• Ensure the car power adapter is connected.
• Make sure that the unit is turned on.
The remote control
• Make sure the infrared remote sensor is not blocked.
does not function.
• Make sure the plastic sheet has been removed from the remote control.
• Point the remote directly at the infrared remote sensor on the unit.
• Replace the battery in the remote control with a new one.
• Use remote control near the unit.
No sound or only a
• The volume control is located on the side of the unit – please try adjusting this.
very low-level sound is
• Make sure ON mode was selected.
heard.
• Make sure the system is not paused. Press the
PLAY button.
• The unit is in fast-forward or fast-reverse mode. Press the
PLAY button.
• Make sure the AUDIO/VIDEO output connections are correct.
• The DTS DVD cannot be decoded to have speaker output.
• The unit is too hot; shut off the unit for 30 minutes to cool it down.
No picture.
• The region number of the disc doesn't match the region number of this unit.
The picture is not
• The DVD is dirty. gently clean the disc.
clear.
• The disc is scratched.
• Adjust the LCD's brightness and contrast using the VIDEO MODE button on the remote
control.
Severe hum or noise is
• The plugs and jacks are dirty. Wipe them with a cloth slightly moistened with alcohol.
heard.
• Clean the disc.
The disc does not play.
• There is no disc inside ("No Disc" appears on the screen).
• Insert the disc correctly with the playback side facing down.
• Clean the disc.
• A non-NTSC disc has been inserted. The unit and disc region number are incompatible.
• Condensation may have formed inside the unit due to a sudden change in temperature.
Wait about an hour for it to clear and try again.
Specifications and external appearance are subject to change without notice.
Limited Warranty
AVC MULTIMEDIA ("AVC") makes the following limited warranty. This limited warranty extends to the original
consumer purchaser and is limited to non-commercial use of the product.
One Year Parts & Labor Warranty
AVC products purchased in the United States are warranted to be free from defects in materials or workmanship for
a period of one year from the date of their original retail purchase. If the unit fails to conform to this warranty, we will
service the product using new or refurbished parts and products, at AVC's sole discretion.
During a period of one year from the effective warranty date, AVC will provide, when needed, service labor to repair
a manufacturing defect at its designated Service Center. To obtain warranty service in the United States, you must
first call our Customer Support Center at 1-800-506-5746 or 1-877-252-6873, during the hours listed in the box
below. The determination of service will be made by AVC Customer Support. PLEASE DO NOT RETURN YOUR UNIT
TO AVC WITHOUT PRIOR AUTHORIZATION. New or remanufactured replacements for defective parts or products
will be used for repairs by AVC at its designated Service Center for one year from the effective warranty date. Such
replacement parts or products are warranted for an additional one year from the date of repair or replacement. The
Customer will be required to ship the unit to the Service Center indicated at the time Customer Support is contacted
to make the necessary repairs. The customer is responsible for all transportation charges to the service facility.
Packaging and Shipping Instruction
When you send the product to the AVC service facility you must use the original carton box and packing material or
an equivalent as designated by AVC.
LIMITED WARRANTY
Your Responsibility
(1) You must retain the original sale receipt to provide proof of purchase.
(2) These warranties are effective only if the product is purchased and operated in the U.S.A. or Canada.
(3) Warranties extend only to defects in material or workmanship, and do not extend to any product or parts which have
been lost or discarded, or damage to product or parts caused by misuse, accident, improper operation or maintenance,
or use in violation of instructions provided with the product, or to product which has been altered or modified without
authorization of AVC, or to products or parts thereof which have had the serial number removed or changed.
Out of Warranty
In the event your product requires repair after the limited warranty period has expired, please contact our
Customer Support Center at 1-800-506-5746, 1-877-252-6873 or
www.RCAav.com
Hours: Monday–Thursday: 9am–7pm, Friday: 9am–5pm, Saturday: 9am–NOON Eastern time.
Important: You are responsible for any transportation, shipping or insurance relative to the return of product to
our Product Returns Center.
All warranties implied by state law, including the implied warranties of merchantability and fitness for a particular
purpose, are expressly limited to the duration of the limited warranties set forth above. With the exception of any
warranties implied by state law as hereby limited, the foregoing warranty is exclusive and in lieu of all other warranties,
guarantees, agreements and similar obligations of manufacturer or seller with respect to the repair or replacement of
any parts. In no event shall AVC be liable for consequential or incidental damages.
No person, agent, distributor, dealer or company is authorized to change, modify or extend the terms of these
warranties in any manner whatsoever. The time within action must be commenced to enforce any obligation of AVC
arising under the warranty or under any statute, or law of the United States or any state thereof, is hereby limited to
one year from the date of purchase. This limitation does not apply to implied warranties arising under state law.
This warranty gives you specific legal rights and you may also have other rights, which may vary, from state to state.
Some states do not allow limitation on how long an implied warranty lasts, when an action may be brought, or the
exclusion or limitation of incidental or consequential damages, so the above provisions may not apply to you.
For more information on other products and services, please visit our web site at
www.RCAav.com
Important: Also keep your "Bill of Sale" as proof of purchase.
Model no. ...............................................................................................Product name ........................................................................................
Type of set ...................................................................................................................................................................................................................
Serial no. .................................................................................................Invoice no. ...............................................................................................
Date purchased ....................................................................................Dealer name ...........................................................................................
www.RCAav.com
FOR SERVICE AND REPAIR, PLEASE VISIT
Printed in China
811-797391W011
Advertisement
