Sanijet PIPELESS SSB2-S115-XX Owner's Manual

Sanijet PIPELESS SSB2-S115-XX Owner's Manual

Pedicure bath, 115v, 60hz, 230v, 50hz

Advertisement

PIPELESS™ PEDICURE BATH
OWNER'S MANUAL
Models: SSB2-S115-XX (115v, 60Hz)
Models: SSB2-S230-XX (230v, 50Hz)
Purity is Premium

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PIPELESS SSB2-S115-XX and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Sanijet PIPELESS SSB2-S115-XX

  • Page 1 PIPELESS™ PEDICURE BATH OWNER’S MANUAL Models: SSB2-S115-XX (115v, 60Hz) Models: SSB2-S230-XX (230v, 50Hz) Purity is Premium...
  • Page 2 Dear Valued Customer: Thank you for purchasing the SANIJET Pipeless™ Pedicure Bath. As the innovator of Pipeless™ hydromassage, SANIJET was founded on the principle that, in spa bath and pedicure bath systems, ® purity is premium. SANIJET’s Reflexology Foot Baths, Pedicure Sinks and Portable Foot Baths provide safe hydromassage, quiet operation, and the ability for quick and easy system disinfection.
  • Page 3: Table Of Contents

    Limited Commercial Warranty ..................2 Safety ........................... 3 Features and Specifications ..................4 Installation: Electrical ....................5 Installation: Standard Self-Rimming ................6 How to Remove for Service ................... 8 Operating Instructions....................9 Dry Run Protection .......................10 SANIJET Pipeless™ Disinfection ..................11 Troubleshooting ......................12...
  • Page 4: General Information

    SANIJET’s responsibility for shipping damage ceases upon delivery of the product in good condition to the carrier. It is the responsibility of the recipient to inspect the packaging for damage. Any damage claims must be filed with the carrier within 2 business days from receipt of shipment.
  • Page 5: Limited Commercial Warranty

    SUBJECT TO the exclusions below. If a tub shell manifests a defect or fails to properly perform under ordinary use within the warranty period, SANIJET will repair or replace it at SANIJET’s election, but shall have no responsibility with respect to removal, reinstallation or transport of the tub shell.
  • Page 6: Safety

    13. SANIJET recommends a qualified plumber and electrician install your Pipeless™ Pedicure Bath. 14. Water supply temperature to the Pipeless™ Pedicure Bath MUST NOT exceed 106° F (41° C). Water temperature in excess of 106°...
  • Page 7: Features And Specifications

    Features and Specifications Model SSB2-S115 / SSB2-S230 Pipeless™ Pedicure Bath FEATURES DIMENSIONS • Two Patented, High Performance, Ultra-Quiet Pipeless™ Jets 19” • Advanced Seal-less Technology Designed for Maintenance-Free Use [49 cm] • Complete Hygiene with Simple Five Minute Disinfection Protocol 9”...
  • Page 8: Installation: Electrical

    Installation: Electrical INSTRUCTIONS PRIOR TO USE WARNING WHEN USING ELECTRICAL PRODUCTS, BASIC PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING: 1. IMPORTANT: Read complete instructions before use. 2. This Pipeless™ Pedicure Bath requires either 115 V, 60 Hz or 230 V, 50 Hz, 2 AMP service and must be connected to a circuit protected by a permanent Ground Fault Circuit Interrupter (GFCI).
  • Page 9: Installation: Standard Self-Rimming

    Installation: Standard Self-Rimming 1. The SANIJET Pipeless™ Pedicure Bath is designed to be installed as a self-rimming or undermount appliance into a raised platform. 2. To cut out the appropriate sized hole in the mounting platform in which the pedicure sink will be installed, place the sink upside down* over the position it will be mounted making sure that the ON/OFF button is closest to the operator’s...
  • Page 10 Installation: Standard Self-Rimming Continued 4. There are four mounting sets included with each pedicure bath to securely mount the bath for a self rimming deck enclosure installation. Each mounting set consists of four (4) flat mounting bars, four (4) threaded rods and four (4) wing nuts (See Image #4).
  • Page 11: How To Remove For Service

    How to Remove for Service To remove the bath from a mounting platform that provides access under the unit: 1. Disconnect the unit’s power cord and #8 AWG bonding wire. 2. Loosen the compression coupling on the drain pipe. 3. Disconnect the four mounting brackets on the bath from the bottom mounting platform. 4.
  • Page 12: Operating Instructions

    Quarter-turn Counter Clockwise 4. Bath additives , including oil based products , can be used in a SANIJET Pipeless™ Pedicure Bath, since their residue can be easily cleaned. CAUTION: Use only low foaming additives, and do not use products that contain sand or silicates.
  • Page 13: Dry Run Protection

    Dry Run Protection IMPORTANT • BEFORE USE check the magnetic impeller rotor is properly installed in the case motor assembly. • BEFORE USE make sure that water is filled to at least 1 in (3 cm) above the jets for proper operation. •...
  • Page 14: Sanijet Pipeless™ Disinfection

    • Disinfectant with Bleach. SANIJET’s Pipeless™ pedicure baths do not require a “fill and drain cycle” during disinfection, for improved water conservation. • For applications requiring quick cleaning between treatments, we recommend a second set of “clean” jet assemblies for quick replacement.
  • Page 15: Troubleshooting

    Troubleshooting NO POWER / NOT OPERATING 1) Power Supply Note: Recommended that all electrical service connections be made by a licensed electrician. a. Ensure switch box power cord is properly plugged into an operational 115 VAC, GFCI power supply. b. For 230 V units with junction box, verify hard wire connections are secure. c.
  • Page 16 SANIJET Customer Service Department ® Toll Free: 877-934-0477 Toll Free Fax: 214-352-0348 E-mail: info@sanijet.com 6200 Maple Avenue Dallas, Texas 75235 sanijet.com 111223...

This manual is also suitable for:

Pipeless ssb2-s230-xx

Table of Contents