American Standard Murro 0954.000 Installation Instructions

BARRIER FREE
MURRO™ UNIVERSAL DESIGN
WALL-HUNG LAVATORY
• Vitreous china
• Rear overflow
• Recessed self-draining deck
• For concealed arm or wall support
• Shown with optional vitreous china shroud/
knee contact guard 0059.020 available
❏ 0954.000 Faucet holes on 102mm (4") Ctrs
(Illustrated)
❏
0954.023 Faucet holes on 102mm (4") Ctrs
• Extra right-hand hole
❏
0954.021 Faucet holes on 102mm (4") Ctrs
• Extra left-hand hole
❏ 0958.000 Faucet holes on 203mm (8") Ctrs
❏ 0955.000 Center hole only
❏ 0955.023 Center hole
• Extra right-hand hole
❏
0955.021 Center hole
• Extra left-hand hole
Nominal Dimensions:
559mm (22") deep, 540mm (21-1/4") wide
Bowl sizes:
394mm (15-1/2") wide, 343mm (13-1/2")
front to back, 127mm (5") deep
❏
0059.020 Shroud/Knee Contact Guard
(Vitreous China) (Must be specified separately)
Compliance Certifications -
Meets or Exceeds the Following Specifications:
• ASME A112.19.2 for Vitreous China Fixtures
To Be Specified:
❏ Color: ❏ White ❏ Bone ❏ Silver
❏ Optional Vitreous China Shroud/Knee
Contact guard: 0059.020
❏ Faucet*:
❏ Faucet Finish:
❏ Supplies:
❏ 1-1/4" Trap:
❏ Nipple:
* See faucet section for additional models available
MEETS THE AMERICANS WITH DISABILITIES ACT GUIDE-
LINES AND ANSI A117.1 ACCESSIBLE AND USABLE
BUILDINGS AND FACILITIES - CHECK LOCAL CODES.
Top of front rim mounted 864mm (34") from finished floor.
For Universal Design Options, top of rim may be mounted
at 813mm (32") from finished floor to meet ADA and ANSI
A117.1 requirements. Check local codes.
© 2008 AS America Inc.
MURRO™ UNIVERSAL DESIGN
WALL-HUNG LAVATORY
540mm
(21-1/4)
FINISHED
WALL
83mm
(3-1/4)
(4) 25mm (1") DIA.
ACCESS HOLES
FOR CONC. ARMS
(2) 16mm (5/8") DIA.
ACCESS HOLES
FOR CONC. ARMS
425mm
(16-3/4)
C/L OF 54mm(2-1/8 DIA.)
HOLES FOR
216mm
CONCEALED ARMS
(8-1/2)
127mm
44mm
(5)
(1-3/4)
406mm 165mm
(16) (6-1/2)
REF.
*
267mm
(10-1/2)
13mm(1/2) DIA.
ANCHOR SCREW
HOLES
89mm
C/L OF 1-1/4
(3-1/2)
O.D. WASTE
1-1/4 O.D.
TAILPIECE
SEE REVERSE FOR ADDITIONAL ROUGHING-IN
DIMENSIONS
NOTES:
● LOOSE KEY ANGLE STOPS, LESS WALL ESCUTCHEONS. SUPPLIES
REQUIRED.
*
DIMENSIONS SHOWN FOR LOCATION OF SUPPLIES AND "P" TRAP ARE
SUGGESTED.
SHROUD/KNEE CONTACT GUARD 0059.020 NOT INCLUDED AND MUST BE
ORDERED SEPARATELY.
■ SUITABLE FOR REINFORCEMENT ONLY, ACTUAL DIMENSIONS MUST
BE TAKEN FROM FIXTURE.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL SUPPORTS.
INSTALLATION INSTRUCTIONS SUPPLIED WITH LAVATORY.
IMPORTANT: Dimensions of fixtures are nominal and may vary within the
range of tolerances established by ANSI Standard A112.19.2.
These measurements are subject to change or cancellation. No responsibility
is assumed for use of superseded or voided pages.
J61
VITREOUS CHINA
102mm
(4)
102mm
197mm
(4)
(7-3/4)
152mm
(6)
559mm
102mm
(22)
(4)
C/L OF 16mm X 29mm
(5/8 X 1-1/8) ANCHOR
SLOTS
41mm
(1-5/8)
146mm
(5-3/4)
*
216mm
(8-1/2)
C/L OF (2) 13mm(1/2) DIA.
KNEE CONTACT GUARD
743mm
ANCHOR HOLES
(29-1/4)
C/L OF SUPPLIES
864mm
AS REQUIRED
(34)
(FRONT
RIM)
FINISHED
FLOOR
Revised 5/06
FINISHED
WALL
203mm
(8)
254mm
(10) REF.
SIDE PROFILE
(ADA)