Gigabyte XPower GH-PSU11-PD Installation Manual

CAUTION
The cooler fan speed levels provided are for reference use only.
Please refer to the motherboard BIOS to verify actual fan speed levels.
The following is not covered by warranty:
1. Incorrect usage or in a manner other than the designed purpose.
2. Nonobservance of its proper operation. ( e.g. over-clocking )
3. Malfunction due to interference from other devices.
4. Unauthorized modification of the product.
5. Malfunction due to unfit specifications on applied Motherboard.
6. Malfunction arising from natural disasters ( earthquake, thunder, fire and flood ).
7. Romoval of or damaged warranty label.
8. The devices inside, including power supply, hard disk, CD-ROM drive, motherboard, cooler, etc,
are not detached from the chassis prior to the transportation, resulting in damage to the
cooler or computer-related devices.
9. Any damage caused by nonobservance of the installation instruction contained in this manual.
Features
1. Compatible with LGA 1156 / 775 & AMD K8 / AM2 CPU platforms.
2. 9cm smart PWM fan with max RPM up to 2800RPM.
3. Special design enabling the mount of an additional fan.
4. Highly conductive heat pipe providing extreme heat dissipation.
5. Special aluminum fin design with large heat dissipation surface area.
6. Direct contact of CPU against heat pipes for efficient heat transfer.
7. Hassle free installation.
Product installation
( AMD K8 / AM2 )
Step 1 Step 2
Apply the thermal grease Clip the short end of the
evenly over the CPU surface. mounting clip on the CPU
Apply a generous amount of socket.
thermal grease.
Step 3 Step 4
Push down on the cooler Press the lever side of the
until it is flush against the mounting clip untill it has
CPU. clipped in.
Step 5 Step 6
Check if the cooler is Plug the 4-pin connector
mounted firmly. of the cooler into the
motherboard's CPU fan
socket.
I nsta l l atio n Gui d e
Specifications
Cooler dimensions: 96x78x122 mm
Fan dimensions: 92x92x25 mm
Heat pipe count: 3
Heat sink material: Aluminum
Input voltage: 12V
Input current: 0.23Amp
Fan speed: 2800 RPM
Noise: 32dBA at full speed
Bearing type: Rifle Bearing
Fan MTBF: 40,000hr
Accessory
Thermal Grease
Product installation
(Intel LGA 1156 / 775)
Step 1 Step 2
Affix the LGA 1156 / 775 Apply the thermal grease
bracket to the MB with the evenly over the CPU surface.
buckles included. Apply a generous amount of
thermal grease.
Step 3 Step 4
Clip the short end of the Push down on the cooler
mounting clip on the CPU until it is flush against the
socket. CPU.
Step 5 Step 6
Press the lever side of the Check if the cooler is
mounting clip until it has mounted firmly.
clipped in.
Step 7
Plug the 4-pin connector
of the cooler into the
motherboard's CPU fan
socket.
GH-PSU11-PD
Support list
Intel® Core
TM
Intel® Core
TM
Intel® Core
TM
Intel® Core
TM
Intel® Pentium® Extreme Edition Series
Intel® Pentium® D Processor Series
Intel® Pentium® 4 Processor Series
AMD AM2
AMD Athlon
AMD Athlon
AMD Athlon
AMD Sempron Series
LGA 775 Bracket LGA 1156 Bracket
Extra cooling fan installation
Step 1
Insert the 4 fan rubber pad
mounts.
Note: 1. Fan size is 9cm
2. Make sure the air flow of both fans
are in the same direction.
Incorrect
i5 / i3 Processor Series
2 Extreme Processor Series
2 Quad Processor Series
2 Duo Processor Series
(LGA775)
FX Series
TM
64x2 Series
TM
64 Series
TM
Fan Mounting Rubber Pad
Step 2
Fit additional fan against
the rubber pad mounts
and pull to secure.
Correct