Kerosene-Fired and Oil-Fired Water Heater Operation and Maintenance Instructions BS-36UFF MODEL (Type C) IMPORTANT READ AND UNDERSTAND INSTRUCTIONS BEFORE INSTALLING OR USING THIS WATER HEATER. RETAIN INSTRUCTIONS FOR FUTURE REFERENCE. CHECK LOCAL CODES AND ORDINANCES FOR PERMITTED USE. CAUTION THIS WATER HEATER SHALL NOT BE USED FOR COMMERCIAL USE OR FOR ANY PURPOSES OTHER THAN HOT WATER SUPPLY USES.
SECTION A: SAFETY TIPS BE SURE TO FOLLOW THE FOLLOWING INSTRUCTIONS. The instructions which are contained in this manual are classified into the following two types, which are "WARNING" and "CAUTION". These instructions are intended to provide important information for safe operation.
Page 3
OTHER PRECAUTIONS This unit is only for indoor use. Avoid its exposure to rain or moisture. Do not use for drinking or cooking until the water supply has been approved by local authorities. Hot water (or cold water) left in heat exchanger or piping must not be used for cooking or drinking. When using a large amount of hot water the temperature may change, even though the temperature setting has not been changed.
SAFETY FEATURES Ignition Safety Device (Flame Sensor) The unit will automatically stop all operations if ignition fails or if the flame fails during combustion. ''WARNING'' lamp will light. Over Heat Protector In order to prevent burns, the over heat protector automatically stops all operations if the water in the heat exchanger reaches abnormally high temperatures due to temperature controller malfunction.
SECTION B: SPECIFICATIONS SPECIFICATIONS Model: BS-36UFF (Type C) Type: Combustion Type Pressure Vapor Flue Pipe Forced Flue Heating Supply System Instantaneous Source of Water Direct Connection to Main Supply Ignition: High Voltage Discharge Spark Fuel: ASTM No.1-K Grade Kerosene or No.1 Fuel Oil...
CONTROL PANEL Temp Selector Knob Power Switch Operation Lamp Burner Lamp Warning Lamp 130° F CAUTION POWER OPERATION BURNER WARNING HOTTER WATER INCREASES THE RISK OF SCALD INJURY. BEFORE CHANGING TEMPERATURE VERY HOT SETTING SEE INSTRUCTION MANUAL. BS-36U COLD ON/OFF THERMOSTAT CONSTRUCTION Heat Exchanger Bi-Metal Switch...
SECTION C: FUEL GUIDE The Toyotomi BS-36UFF is designed for use with ASTM No. 1-K Grade kerosene or No.1 fuel oil only. Use of low-quality kerosene will cause burner performance to drop, leading to abnormal combustion and reduced the unit life.
SECTION D: OPERATION FUELING WARNING: Use KEROSENE (ASTM No. 1-K) or No.1 fuel oil only. Never use gasoline, thinner, benzene, light oil or waste oil. CAUTION: Make sure that the fuel is clean and free from dirt and water. Water and dirt may cause com- bustion failure and shorten the life of components such as the fuel pump.Be sure to refuel before the tank runs out.
OPERATION ¡ Hotter water or high temperature setting increases the risk of scald injury. CAUTION: ¡ Thermostat has been set at factory to about 130°F. ¡ Risk of scald injury. When using a shower, feel the temperature of the water with your hand before getting under the water.
¡Seasonal change of water temperature from the main water source results in different hot NOTE: water temperature supplied. Use hot water supply faucet to control hot water temperature, or readjust temperature setting. ¡The hot-cold mixing faucet is recommended to ensure safe and comfortable use of the water heater.
DRAINING WATER When you do not plan to use the unit for an extended period, the following procedures are recommend- 1. Turn the unit off. 2. Disconnect the power supply cord. 3. Close the fuel tank valve securely. 4. After closing the main water supply valve, open up all the faucets. 5.
SECTION E: ROUTINE MAINTENANCE INSPECTION AND MAINTENANCE WARNING: RISK OF INJURY FROM MOVING PARTS AND ELECTRICAL SHOCK. Disconnect the power supply cord before inspecting and servicing unit.All repairs should be left to professionals. RISK OF BACKFIRE AND INDOOR POLLUTION. Before operation make sure the flue pipe is free of snow, icing, leaves, bird's nest or strong drafts.
10. TEMPERATURE AND PRESSURE RELIEF VALVE (ONCE A MONTH) The temperature and pressure relief valve may become immovable at times due to corrosion of pipes or mineral deposits In the pipes. Pull up the lever of the temperature and pressure relief valve every month and make sure the valve is movable.
Page 15
PROBLEM CAUSE SOLUTION POWER LAMP FAILS Disconnected power supply cord Connect power supply cord. TO TURN ON ALARM LAMP Thermistor malfunction Consult your dealer. LIGHTS AFTER Out of water in heat exchanger Supply water. TURNING ON. Flame sensor malfunction Consult your dealer. Light is received on the receiving Consult your dealer.
WHO IS COVERED : The original purchaser at retail. WHAT WE WILL DO : TOYOTOMI will either repair or replace, at its option, all defective parts free of charge that are covered by this limited warranty on a carry-in basis, to your nearest authorized dealer or distributor of TOYOTOMI.