Table of Contents
Advertisement
Quick Links
FOR New Remote Control
Installation
Use these in place of the "rocker
switch and solenoid "section of
instructions in your roll tarp
owner's manual.
Use these for installation of
remote for ROLTEC
Hopper Conversions.
IMPORTANT!
READ AND UNDERSTAND THESE INSTRUCTIONS, WITH
REMOTE KIT FOR SAFETY, INSTALLATION, DANGER,
OPERATION, MAINTENANCE AND PROGRAMMING FOR YOUR
REMOTE CONTROL PRODUCT. SAVE ALL INSTRUCTIONS
WITH YOUR ROLL TARP OWNERS MANUAL FOR FUTURE
REFERENCE.
Electric
TM
Tested. Trusted. Guaranteed.
Remote Control
Instructions
FOR Existing Electric
Remote Control Installation
Disconnect (+) and (-) battery
terminal connections. Disable
existing switch and solenoid - they
will not be used with this system.
Install the remote control in
accordance with these instructions
included with remote control kit.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for AGRI-COVER Command-10
-
Page 1: Remote Control
Remote Control Instructions FOR Existing Electric FOR New Remote Control Remote Control Installation Installation Disconnect (+) and (-) battery Use these in place of the “rocker terminal connections. Disable switch and solenoid “section of existing switch and solenoid - they instructions in your roll tarp will not be used with this system. -
Page 2: Wiring Instructions
Parts Diagram (for part No. 80300) Parts included: The above diagram shows only parts that are included in the Command-10 remote control kit. All other parts shown in the following ® instructions would be found in a new electric kit or would be already installed on an existing electric system. - Page 3 50 amp modified reset circuit This Red Striped breaker installed as shown. Circuit Breaker Wire to Battery (+) NOTE: If kit came pre-wired with 40 Amp breaker, remove it and use 50 Amp breaker supplied loose in Command-10 kit. ®...
- Page 4 STEP 5 For TRAILER UNITS with Heavy Duty connector use terminals to attach wire to socket. STEP 6 For motor terminal connections, if needed refer to electrical section of roll tarp owner’s manual. STEP 7 Now connect red wire to battery (+) post and then black wire to battery (-) post.
- Page 5 DUAL POLE CONNECTOR (USED IN SOME APPLICATIONS) (M1) HEAVY GAGE WIRE (M2) Note: Use dielectric grease (packet included) at all ellectrical connections. NOTE: This remote system requires a 50 amp modified reset circuit breaker. If breaker trips and does not reset, it may have detected a continuous short and will not reset until short is repaired.
-
Page 6: Safety Instructions
Operating Instructions Learning How to Use and Operate Your AGRI-COVER Command-10 Wireless Remote ® Introduction This wireless controller provides push-button wireless control. The remote transmitter is simple to use and provides convenient reliable operation and is suitable for a wide variety of applications. -
Page 7: Pre-Programmed Mode
Pre-Programmed Mode (how to use Remote’s pre-programmed mode to open and close tarp) Your electric system can be operated wirelessly by the Remote. The Remote is designed to provide safe and easy operation of the system and features an auto-lock mode to help prevent unintended operation. To Unlock and Lock Remote The Remote will unlock automatically when lid is opened. - Page 8 Programming a Remote Control to a Receiver Your Remote and Receiver will come pre-programmed to each other. If they are not, follow the procedure below. STEP 1 Clear Receiver Power on receiver. Press and hold the Programming button until the indicator light turns steady green.
- Page 9 STEP 3 Program Primary Remote to Receiver Power on both receiver and remote. On remote tap Programming button once, indicator light will flash fast green. On receiver, press and hold Programming button until both remote and receiver slow flash green at the same rate.
- Page 10 Optional Instructions to Program Auxiliary Remotes STEP 1 Create a Auxiliary Remote Open cover to unlock remote. Push and hold Select button then push and hold Programming button while Select button is still being held. Hold both buttons until indicator light flashes red. Release both buttons. Press CLOSE button.
-
Page 11: Battery Replacement
Battery Replacement Your wireless remote is powered by two AAA 1.5V Alkaline Batteries. If remote becomes unresponsive or if low battery indicator is flashing replace batteries. To change batteries, remove the battery cover exposing two batteries. Replace both batteries with two of same brand and size. Reassemble battery cover. -
Page 12: General Troubleshooting
General Trouble Shooting 1. If system has a master control switch, make sure it is turned to “ON” position. 2. Check all of the wiring components: Check (+) and (-) wire connections on Vehicle Battery. Check all wiring connections retighten and re-crimp if loose, replace if corroded. - Page 13 Trouble Shooting Receiver (Assuming Remote is working properly) Problem Issue: Check or Try... 1. System will not operate with a. If system has a master control remote or toggle switch. switch, make sure it is turn to (Cannot hear a clicking noise “ON”...
- Page 14 Trouble Shooting Remote (Assuming Receiver is working properly) Problem Issue: Check or Try... 3. Remote transmitter doesn’t a. Check remote for dead batteries, work. None of the lights turn if batteries are dead replace with on when remote is turned on. new quality high capacity batteries.
- Page 15 Trouble Shooting System Problem Issue: Check or Try... 5. The remote and toggle a. Check pin connections in shaft switch will operate the motor, between motor and tarp tube. If but tarp motor turns freely missing, replace sheared bolt or and tarp won’t move.
- Page 16 Agri-Cover, Inc. Customer Service Dept. 3000 Hwy. 281 SE, PO Box 508 Jamestown, ND 58402 701-251-1427 • 8:00 a.m. - 5:00 p.m., Central Time Monday through Friday, except holidays. Part No. 80500_D Copyright 2013, All Rights Reserved. Agri-Cover, Inc. 042814...
Need help?
Do you have a question about the Command-10 and is the answer not in the manual?
Questions and answers