Oakton Tech Board Operating Instructions

Operating Instructions

Thank you for purchasing a
Tech Board ™ —the ultimate
technical organizer!
It features:
• A 24 hour count-up stopwatch
• Calculator with full memory and % key
• Real-time clock with time of day and calendar
• Selectable audible alarm clock
Main Function Button Descriptions
The TECH BOARD features three main function buttons:
1. the MODE button
2. the START/STOP button
3. the LAP/RESET button
The MODE button lets you scroll through 4 modes:
1. Time/calendar mode
you see:
2. Stopwatch mode
you see:
3. Alarm set mode
you see:
4. Time/calendar set mode
you see:
The START/STOP button lets you:
1. In time/calendar mode:
2. In stopwatch mode:
3. In alarm set mode:
4. In time/calendar set mode:
The LAP/RESET button lets you:
1. In time/calendar mode:
2. In stopwatch mode:
3. In alarm set mode:
4. In time/calendar set mode:
Time/Calendar Functions
How to enter time/calendar mode
1. Press the MODE button until the display scrolls to the time/calendar
mode (upper display will show one nonflashing day of the week).
2. To see the date, press the START/STOP button.
3. To see the alarm set time, press the LAP/RESET button.
NOTE: Unless the alarm indicator
display), the alarm will not sound at the shown time.
How to set time and calendar
1. Scroll to time/calendar set mode (upper display will flash "TUE").
2. Press the LAP/RESET button to scroll between clock parameters.
The display scrolls through seconds, minutes, hours, day, month, day
of week, then back to seconds.
Tech Board ™
SUN MON TUE WED THU FRI SAT
View time, date and alarm set time
Upper display shows current day
Perform all stopwatch functions
Upper display flashes "SUN FRI SAT"
Set or deactivate alarm
Upper display flashes "MON"
Set time and date
Upper display flashes "TUE"
view the current date
start and stop the stopwatch
change the alarm set time
change the time and date
view the alarm set time
time split laps and reset stopwatch
scroll through alarm set parameters
scroll through time/date parameters
is on (upper right corner of the
alarm indicator
upper display
ON/C
CE
+/–
• Common conversion tables and a Periodic
Table of the Elements for quick reference
• Sturdy clipboard that tightly holds your papers
• Solar power cell—no batteries required
3. When you have selected the parameter you want to change, hold
START/STOP button to adjust the clock or calendar.
4. Repeat step 3 until you have selected the correct time and date.
NOTE: You can also select a 12-hour clock (a.m. and p.m.)
or a 24-hour clock. To select 12 or 24 hour time:
a. Scroll to the hours parameter.
b. Hold the START/STOP button until you reach the appropri-
ate time scale. The a.m./p.m. clock will display "A" or "P"
in the seconds place; the 24 hour clock will display "H" in
the seconds place.
5. When you have selected the correct time and date, press MODE to
scroll to the time/calendar display.

Alarm Functions

You can set alarm to sound for one minute at a specific time, and/or for a
brief time once every hour. If the alarm set for a specific time is turned on,
you will see the alarm indicator
How to set alarm to sound at a specific time
1. Press the MODE button until the display scrolls to alarm set mode
(upper display flashes "MON").
2. Press the LAP/RESET button to select hours or minutes.
3. When you have selected the parameter you want to change, hold
START/STOP button to adjust the clock.
4. When you have selected the correct alarm time, push the MODE but-
ton to return to time display. The alarm indicator should now be on.
How to turn off alarm set for a specific time
1. Scroll to time/calendar mode (upper display shows 1 nonflashing day).
2. Press the LAP/RESET button to see the alarm set time.
3. While holding the LAP/RESET button, press the START/STOP button.
4. The alarm indicator will turn off.
NOTE: If the alarm was already off, this same action will turn alarm on.
How to turn on and turn off hourly alarm
1. Scroll to time/calendar mode (upper display shows 1 nonflashing day).
2. Press the LAP/RESET button.
3. While holding the LAP/RESET button, press the MODE button.
4. If the hourly alarm was on, the entire upper display disappears briefly,
and the hourly alarm is now off. If the hourly alarm was off, the entire
upper display flashes briefly, and the hourly alarm is now on.
START/STOP button
MODE button
MODE 7 8 9
MRC 4 5 6
M– 1 3
2
.
M+ 0 %
in the upper right corner of the display.
LAP/RESET button
÷
S/S
x
L/R
+
–
=/COUNTUP