Download Print this page

LumaPro 50 Watt Metal Halide Patio Light 2LBL7 Operating Instructions Manual

50 watt metal halide patio light & 70 watt high pressure sodium patio light

Advertisement

Available languages

Available languages

Quick Links

Operating Instructions & Parts Manual
Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain
the product described. Protect yourself and others by observing all safety information. Failure to comply could
result in personal injury and/or property damage! Save these instructions for future reference.
NOTE: All wiring must be run in accordance with the National Electrical Code (Canadian Electrical Code in Canada) through conduit or
another acceptable means. Contact a qualified electrician if there is any question as to the suitability of the system.
Lamp in Fixture Contains Mercury. Dispose According
to Local, State, or Federal Laws.
WARNING: Turn power off at the fuse or circuit
breaker.
This fixture can be mounted on a wall with, or without using a flush-
mounted junction box. Do not attempt to mount this fixture on a
surface-mounted "Wet Location" junction box. Use the instructions
below that apply to your application.
Installation Using A Junction Box
Note: If your junction box protrudes out of the wall slightly, you may
want to use the enclosed gasket so less caulking is required.
1. Hold the Mounting Bracket and Gasket over the junction box.
Thread the supply wires through the large hole in the back of
the Mounting bracket. Select the holes in the mounting bracket
that line up with the screw holes in the junction box. Make sure
the bottom of the Mounting Bracket is level. Secure with the two
#8 screws provided.
Installation Without A Junction Box
1. Select a location on a flat wall with structurally sound wood and
from 5 to 25 feet from the ground. The wood should be at least
one inch thick to safely secure the fixture.
2. Use the Mounting Bracket as a template. Hold it at the desired
mounting location (making sure the bottom is level), and mark
four mounting holes.
3. Use four #8 or #10 wood screws or galvanized deck screws at
least 1 inch long (not provided) to secure the Mounting Bracket
to the wall. It may be necessary to drill appropriate pilot holes if
mounted to hardwood to avoid splitting.
4. Remove the knockout in the bottom of the Mounting Bracket, and
bring your supply wires through this knockout using appropriate
flexible conduit or other approved means of wiring.
Complete The Installation
1. Put the Temporary Pin through the holes in the Mounting Bracket.
2. This fixture must be grounded. Connect the supply ground wire to
the green ground screw. You can also attach a bare or green "pigtail"
to the green ground screw, then connect the ground pigtail to the
supply ground when the other supply wires are connected.
3. Slide the fixture onto the Mounting Bracket, and allow the fixture
to rest on the Temporary Pin.
4. Connect the fixture wires to the supply wires (black to black,
white to white, and if a ground pigtail was added above, con-
HEA 012
Printed in China
02/08
Model 2LBL7: 50 Watt Metal Halide Patio Light
®
Model 2LBL8: 70 Watt High Pressure Sodium Patio Light
nect this pigtail to the supply ground wire). Secure with the wire
connectors provided.
5. Remove the Temporary Pin, and slide the fixture all the way down
onto the Mounting Bracket making sure no wires get pinched.
6. Install the screw through the bottom of the Mounting Bracket and
into the fixture housing. Tighten this screw.
7. Install lamp (provided). Lamp rating must match the rating of the
fixture.
Model 2LBL7: 50 watt metal halide M110/O open rated lamp.
Model 2LBL8: 70 watt high pressure sodium type S62 lamp.
8. Caulk fixture mounting surface with silicone weather sealant.
To test operation during daylight, cover the photocontrol with black
tape. Turn on the power. The light will take up to ten minutes to reach
full brightness. Remove the tape from the photocontrol and your unit
will operate automatically—on at dusk, off at dawn.
Photocontrol
Mounting
Lamp
Bracket
2LBL7, 2LBL8
Fixture
Ground
Screw
Temporary
Pin
Gasket
(Optional)
598-1319-02
LPG-5659, LPG-5679

Advertisement

loading
Need help?

Need help?

Do you have a question about the 50 Watt Metal Halide Patio Light 2LBL7 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for LumaPro 50 Watt Metal Halide Patio Light 2LBL7

  • Page 1 Operating Instructions & Parts Manual Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by observing all safety information. Failure to comply could result in personal injury and/or property damage! Save these instructions for future reference. ®...
  • Page 2 Ballast Assembly Replacement Instructions Ballast assembly can be replaced without the cutting of any wires. Use of a qualified electrician is recom- mended. WARNING: Turn power off at the fuse or circuit breaker. 1. Remove plastic cover. 2. Remove bulb. 3.
  • Page 3 Ballast Assembly Replacement Instructions Ballast assembly can be replaced without the cutting of any wires. Use of a qualified electrician is recom- mended. WARNING: Turn power off at the fuse or circuit breaker. 1. Remove plastic cover. 2. Remove bulb. 3.
  • Page 4: Year Limited Warranty

    1 YEAR LIMITED WARRANTY: Should this product fail to perform satisfactorily due to a defect or poor workmanship within one year of date of purchase, return it to the place of purchase and it will be replaced, free of charge. Incidental or consequential damages are excluded from this warranty.
  • Page 5 Manual de Instrucciones y Partes Por favor lea y guarde estas instrucciones. Léalas cuidadosamente antes de intentar armar, instalar, operar o dar mantenimiento al producto descrito. Protéjase Ud. y los otros observando toda la información de seguridad. ¡Si no lo hace podría ocasionar lesión al personal y/o daño al equipo! Guarde estas instrucciones para referencia futura.
  • Page 6 Instrucciones para el cambio del conjunto estabilizador El conjunto estabilizador puede cambiarse sin nece- sidad de cortar ningún alambre. Se recomienda que lo haga un electricista calificado. ADVERTENCIA: Apague la energía en el fusible o cortacircuitos. 1. Retire la cobertura plástica. 2.
  • Page 7 Instrucciones para el cambio del conjunto estabilizador El conjunto estabilizador puede cambiarse sin nece- sidad de cortar ningún alambre. Se recomienda que lo haga un electricista calificado. ADVERTENCIA: Apague la energía en el fusible o cortacircuitos. 1. Retire la cobertura plástica. 2.
  • Page 8 GARANTíA LIMITADA A UN (1) AñO: Si este producto fallara en funcionar satisfactoriamente debido a un defecto o mala fabricación dentro de un año desde la fecha de compra, devuélvalo al sitio donde lo compró y se lo reemplazará, sin costo para usted.
  • Page 9 Mode d’emploi et guide des pièces Veuillez lire et conserver ces directives. Lisez-les attentivement avant de commencer à assembler, installer, utiliser ou entretenir le produit qui y est décrit. Assurez en outre votre protection et celle des autres personnes qui vous entourent en respectant toutes les consignes de sécurité.
  • Page 10 Directives de remplacement du ballast Il est possible de remplacer le ballast sans couper de fils. Nous recommandons de recourir aux services d’un électricien qualifié. AVERTISSEMENT : Coupez l'alimentation au disjoncteur ou au fusible. 1. Retirez le couvercle de plastique. 2.
  • Page 11 Directives de remplacement du ballast Il est possible de remplacer le ballast sans couper de fils. Nous recommandons de recourir aux services d’un électricien qualifié. AVERTISSEMENT : Coupez l'alimentation au disjoncteur ou au fusible. 1. Retirez le couvercle de plastique. 2.
  • Page 12: Garantie Limitée D'un An

    GARANTIE LIMITéE D’UN AN : En cas de défaillance de ce produit attribuable à un défaut de fabrication au cours de l’année suivant la date d’achat, retournez-le chez le détaillant où vous l’avez acheté où il sera remplacé sans frais. Cette garantie ne vise pas les dommages accessoires ou consécutifs.

This manual is also suitable for:

2lbl8
Save PDF