Secure Home DualBrite SH-5318 Owner's Manual

Motion sensor light control with 2-level lighting
Table of Contents

Advertisement

Available languages

Available languages

Quick Links

Motion Sensor
Light Control with
2-Level Lighting
Models SH-5318
Features
• Turns on lighting when motion is detected.
• Automatically turns lighting off.
• D
B
Timer.
®
ual
rite
• Photocell keeps the lighting off during daylight hours.
• LED indicates motion was sensed (day or night).
This package includes:
Lamp Holders
Cover Plate
Light Control
Mounting Bolt
Mounting Strap
2 Shells*
* Model SL-5318 only
Requirements
• The light control requires 120-volts AC.
• If you want to use Manual Mode, the control must be
wired through a switch.
• Some codes require installation by a
qualified electrician.
• This product is intended for use with the enclosed
gasket and with a junction box marked for use in wet
locations.
© 2007 HeathCo LLC
D
B
ual
rite
Rubber Plug
Plastic Hanger
Sensor
2 Wire
Connectors
Gasket
6 Screws
(3 sizes included)
OPERATION
®
Mode:
On-Time
Test
5 Seconds
Auto
1, 5, or 20 Min
Manual
To Dawn*
Accent
3, 6 Hr, to Dawn
* resets to Auto Mode at dawn.
Note: When first turned on wait about 1
the circuitry to calibrate.
Put ON-TIME switch
on the sensor bottom
to TEST and the D
B
switch OFF.
®
rite
Put the ON-TIME switch in the 1, 5,
or 20 minute position.
MANUAL MODE
Manual mode only works at night
because daylight returns the sensor
to AUTO.
Flip the light switch off for one second
then back on to toggle between AUTO
and MANUAL MODE.
Manual mode works only with the
ON-TIME switch in the 1, 5, or 20
position.
Mode Switching Summary
TEST
AUTO
MANUAL MODE
* If you get confused while switching modes, turn the
power off for one minute, then back on. After the cali-
bration time the control will be in the AUTO mode.
D
ual
Light comes on half bright for selected time after dusk
(Off, 3 hr., 6 hr., until dawn). Selecting OFF disables
this feature. The motion sensing features will continue
to work as described in this manual. If motion is sensed,
the light turns on full bright for the ON-TIME (1, 5, or
20 minutes) then returns to dim mode.
Works: Day Night
/
minutes for
1
2
TEST
ON-TIME
D
ual
-
ual
TEST 1 5 20
Off 3 6 Dusk to
AUTO
ON-TIME
TEST 1 5 20
1 Second OFF
... back on.
Move ON-TIME Switch to
1, 5, or 20 minutes
Flip light switch off
for one second then
back on*
B
Timer
®
rite
598-1154-01
x
x
x
x
x
B
®
rite
Dawn
then...

Advertisement

Table of Contents
loading

Summary of Contents for Secure Home DualBrite SH-5318

  • Page 1 Motion Sensor Light Control with 2-Level Lighting Models SH-5318 Features • Turns on lighting when motion is detected. • Automatically turns lighting off. • D Timer. ® rite • Photocell keeps the lighting off during daylight hours. • LED indicates motion was sensed (day or night).
  • Page 2: Installation

    INSTALLATION For easy installation, select an existing light with a wall switch for replacement. Wall Mount Eave Mount For under eave installation, the sensor head must be rotated as shown in the next two steps for proper operation and to avoid the risk of electrical shock. For eave mount only: ❒...
  • Page 3: Test And Adjustment

    TEST AND ADJUSTMENT ❒ Turn on the circuit breaker and light switch. NOTE: Sensor has a 1 minute warm up period before it will detect motion. When first turned on, wait 1 minutes. ❒ Turn the RANGE control to the mid position, to OFF and the ON-TIME control to the ®...
  • Page 4: Troubleshooting Guide

    TROUBLESHOOTING GUIDE SYMPTOM POSSIBLE CAUSE Lights will not come 1. Light switch is turned off. 2. F l o o d l i g h t i s l o o s e o r burned out. 3. Fuse is blown or circuit breaker is turned off.
  • Page 5 Control de luz y detector de movimiento D Modelos SH-5318 Características • Prende la luz cuando detecta movimiento. • Apaga la luz automáticamente. • Temporizador luz de adorno, D • La fotocélula mantiene la luz apagada durante el día. • LED indica que se ha detectado movimiento (durante el día o la noche).
  • Page 6 INSTALACION Para una fácil instalación escoja una luz con un interruptor de pared. Montaje en pared Montaje en alero Para instalarlo bajo el alero, la cabeza del detector debe ser girada como se muestra en los dos pasos siguientes para evitar el riesgo de un choque eléctrico. Sólo para montaje eléctrico: ❒...
  • Page 7: Prueba Y Ajuste

    PRUEBA Y AJUSTE ❒ Prenda el cortacircuitos y el interruptor de luz. NOTA: El detector tiene un período de cerca de 1 minutos de calentamiento antes de detectar movimiento. Cuando lo prenda por primera vez, espere 1 minutos. ❒ Gire el control de sensibilidad (SENS) a la mitad, el de adorno (D ) a apagado (OFF) y el control de ®...
  • Page 8: Guia De Investigacion De Averias

    GUIA DE INvESTIGACION DE AvERIAS SINTOMA POSIBLE CAUSA La luz no se enci- 1. El interruptor de luz está apaga- ende. 2. El faro está flojo o fundido. 3. El fusible está quemado o el cortacircuitos está apagado. 4. La desconexión de luz del día está en efecto.

Table of Contents