If you are unable to insert the plug into an outlet contact a qualified electrician to have a suitable outlet installed. Do not leave the laminator power on overnight. Unplug the laminator at the end of the day. OfficeZone 1-800-543-5454 www.officezone.com...
The ML27 will accept rolls of laminating film up to 27” wide in all film thicknesses. Paper and card stock up to 1/16” (1.6mm) thick may be laminated without adjusting the rollers. OfficeZone 1-800-543-5454 www.officezone.com...
Use two people when removing the laminator from the shipping container. Components... Figure 1 below shows the location of the major components and controls of the ML27. You should become familiar with these before operating the laminator. Figure 1 OfficeZone 1-800-543-5454 www.officezone.com...
Refer to the MAINTENANCE section for cleaning instructions. Loading Laminating Film onto Mandrels... Slide the film onto the mandrel as in figure 2 below. Note that one mandrel is labeled TOP and the other BOTT (for bottom). They are not interchangeable. Figure 2 OfficeZone 1-800-543-5454 www.officezone.com...
NOTE: The shiny side of the film must always go against the Heat Shoes. CAUTION! The Heat Shoes reach a temperature of up to 350°F. Do not touch the surface of the Heat Shoes. Figure 5 Figure 6 OfficeZone 1-800-543-5454 www.officezone.com...
4. If necessary locate the knob on the right side of the bottom Supply Mandrel and adjust the tension as in step 3 above. 5. If you are not ready to laminate, turn the Motor Switch and Heat Switch off. OfficeZone 1-800-543-5454 www.officezone.com...
(optional), two pages (side-by-side) may be laminated and trimmed in a single operation. As the web exits the unit, these pages may then be sepa- rated with the additional slitter blade. OfficeZone 1-800-543-5454 www.officezone.com...
3. Press the Motor Switch to the on position. The film will begin moving through the lamina- tor. 4. After clear laminating film exits the Pull Rollers at the rear of the machine you may slide the first item to be laminated into the laminator with the right edge along the Paper Guide. OfficeZone 1-800-543-5454 www.officezone.com...
7. You may coat subsequent boards now, one directly behind the other, so that the board in front becomes the leader board. If at any time you have adhesive going through the machine without mountboard, be sure to pull the adhesive on the exit side of the machine to prevent a wrap-around. OfficeZone 1-800-543-5454 www.officezone.com...
8. You may mount subsequent prints now, one directly behind the other so that the board in front becomes the leader board. 9. Once your last print has completely exited the laminator, turn the MOTOR and FAN switches OFF and use the trimmer to remove the mounted and laminated prints. OfficeZone 1-800-543-5454 www.officezone.com...
Wrinkles appear on the laminated items running parallel with the out- side edges. ACTION: Increase roller tension on top and/or bottom supply rolls. Reduce heat shoe temperature. Clean heat shoes of residual adhesive. See MAINTENANCE section for cleaning instructions. OfficeZone 1-800-543-5454 www.officezone.com...
2. Remove the Feed Table. 3. Cut the plastic film at the top and bottom mandrels. 4. Turn the Motor Switch on and pull the film out of the back of the machine. 5. Turn the Motor Switch off. OfficeZone 1-800-543-5454 www.officezone.com...
Be sure to have your machine serial number and date of purchase handy. If the laminator must be returned to the dealer, proper packaging and freight charges are your responsibility. Shipping damages as a result of improper packaging is not covered under the terms of this warranty. OfficeZone 1-800-543-5454 www.officezone.com...