Related Manuals for AEG FAVORIT F65478 VI-S
Summary of Contents for AEG FAVORIT F65478 VI-S
- Page 1 User’s Manual FAVORIT F65478 VI-S 18” Fully Integrated Dish Washer - User’s Manual...
-
Page 2: Table Of Contents
CONTENTS Contents INTRODUCTION ........................5 SAFETY INFORMATION ......................7 INSTALLATION MATERIAL....................10 Kit supplied with dishwasher (models F65478VI-S / F89078VI-S) ......11 DIMENSIONS OF DISHWASHER ..................12 INSTALLATION AND HOOK-UP..................13 Leveling ............................14 5.1.1 Mounting the feet (only for some models) ..............14 5.1.2 Levelling the appliance ......................15 Connections ..........................16 5.2.1 Connecting to the water supply ..................17... -
Page 3: Introduction
INTRODUCTION INTRODUCTION Thank you for choosing one of our products. To install this dishwasher cor- rectly and safely, please read this manual carefully. The manual is divided into sections giving you a step-by-step guide to installation of the appli- ance. The texts are easy to understand and are complete with detailed illustrations. - Page 4 INTRODUCTION Symbols used in this manual (see tab. 1-01) DANGER. This symbol highlights information and warnings which, if not observed, may compromise personal safety or damage the appliance. DANGER OF ELECTROCUTION. This symbol highlights information and warnings of an electrical nature which, if not observed, may compromise personal safety or damage the appliance.
-
Page 5: Safety Information
WARNINGS SAFETY INFORMATION THIS MANUAL FORMS AN INTEGRAL PART OF THE APPLIANCE AND MUST THEREFORE BE KEPT INTACT TOGETHER WITH THE MACHINE. BE- FORE USING THE APPLIANCE, CAREFULLY READ ALL THE INSTRUCTIONS CONTAINED IN THIS MANUAL. INSTALLATION MUST BE PERFORMED BY A QUALIFIED TECHNICIAN, IN COMPLIANCE WITH THE REGULATIONS IN FORCE. - Page 6 WARNINGS TWO PEOPLE WEARING SAFETY GLOVES ARE REQUIRED TO LIFT THE DISHWASHER. DO NOT LEAVING DISCARDED PACKAGING MATERIALS UNSUPERVISED WITHIN THE HOME. SEPARATE THE VARIOUS PACKAGING MATERI- ALS AND TAKE THEM TO THE NEAREST SORTED WASTE COLLECTION CENTRE. KEEP CHILDREN, PHYSICALLY AND/OR MENTALLY IMPAIRED ADULTS, AND ANIMALS AWAY FROM PACKAGING WASTE;...
- Page 7 WARNINGS DO NOT USE EXTENSION CORDS, ADAPTORS OR SHUNT CONNECTIONS IN ORDER TO AVOID THE POSSIBILITY OF OVERHEATING OR BURNING, WITH CONSEQUENT FIRE HAZARD. THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR DAM- AGE TO PERSONS, ANIMALS OR PROPERTY RESULTING FROM FAIL- URE TO OBSERVE THE ABOVE PRECAUTIONS, FROM TAMPERING WITH EVEN A SINGLE COMPONENT OF THE APPLIANCE, OR FROM THE USE OF UNORIGINAL SPARE PARTS.
-
Page 8: Installation Material
INSTALLATION INSTRUCTIONS INSTALLATION MATERIAL To install the dishwasher correctly, the following materials are required: • Phillips screwdriver (ref. A fi g. 3-01); • spirit level (ref. B fi g. 3-01); • tape measure (ref. C fi g. 3-01); • compass saw (ref. D fi g. 3-01); •... -
Page 9: Kit Supplied With Dishwasher (Models F65478Vi-S / F89078Vi-S)
INSTALLATION INSTRUCTIONS Kit supplied with dishwasher (models F65478VI-S / F89078VI-S) The kit supplied with the dishwasher comprises: • adhesive steam guard (ref. A fi g. 3-02); • 1 steel steam guard (ref. B fi g. 3-02);* • 1 template for door panel (ref. C fi g. 3-02); •... -
Page 10: Dimensions Of Dishwasher
INSTALLATION INSTRUCTIONS DIMENSIONS OF DISHWASHER (See fi g. 4-01) Model A (height) B (width) C (depth) 86 cm ÷ 91 cm 59.7 cm ÷ 59,9 cm 57 cm F89078VI-M 33-55/64” ÷ 35-55/64” 23-1/2” ÷ 23-37/64” 22-7/16” 86 cm ÷ 91 cm 59.7 cm ÷... -
Page 11: Installation And Hook-Up
INSTALLATION INSTRUCTIONS INSTALLATION AND HOOK-UP DURING INSTALLATION, TAKE CARE NOT TO INJURE YOURSELF ON THE SHARP EDGES OF THE APPLIANCE. Remove the polystyrene rack blocks. Position the appliance in the chosen instal- lation position. The sides and rear of the appliance can lie against kitchen units or walls. -
Page 12: Leveling
INSTALLATION INSTRUCTIONS Leveling 5.1.1 Mounting the feet (only for some models) Turn the appliance upside-down (see fi g. 5-01). Tighten the nut (see ref. A fi g. 5-01) onto the threaded pin (see ref. B fi g. 5-01) of the foot and then fi t the supplied washer; do this on both feet. Screw the feet onto the appliance until the washers touch the base;... -
Page 13: Levelling The Appliance
INSTALLATION INSTRUCTIONS 5.1.2 Levelling the appliance Level the appliance using the relative adjustable feet (e.g.: ref. A fi g. 5-02); use an open-ended wrench to rotate the feet until the dishwasher is perfectly level. Some models are fi tted with just one rear foot which can be adjusted with a screw located at the bottom front of the appliance (ref. -
Page 14: Connections
INSTALLATION INSTRUCTIONS Fig. 5-03 Connections Install the dishwasher so as to allow ease of access to the electrical and hydraulic connections through the adjacent unit. These connections must never be behind the dishwasher. The inlet and drain hoses can be pointed in all directions. make sure that they are not bent, crushed or too tight. -
Page 15: Connecting To The Water Supply
INSTALLATION INSTRUCTIONS A through hole with a diameter of at least 8 cm (5/32”) is required to pass the hoses and power cord (ref. A fi g. 5-05). Make sure there area no rough edges that could damage the power cord or hoses. If the dishwasher is installed in a metal unit protect the edge of the through hole for the hoses and power cord with a gasket. -
Page 16: Connecting To The Water Tap
INSTALLATION INSTRUCTIONS 5.2.1.1 Connecting to the water tap Connect the inlet hose to a threaded ¾” gas cold water tap, fi tting the supplied fi lter (ref. A fi g. 5-06). Firmly secure the hose by tightening the relative ring nut with your hands (ref. - Page 17 INSTALLATION INSTRUCTIONS Do not cut the inlet hose (see fi g. 5-07). If the hose is cut, the dishwasher will not work, water will leak and you may be injured. If the hose is too long, wind it up tidily and place it behind the appliance. The cable harness and electrical components must not come into contact with the hydraulic system and the water inlet and drain hoses.
-
Page 18: Connecting The Drain Hose
INSTALLATION INSTRUCTIONS 5 .2.1.2 Connecting the drain hose Connecting to a drain Insert the relative hose into a drain with a minimum diameter of 4 cm (1-37/64”) (ref. A fi g. 5-09); alternatively, place the hose on the sink (ref. B fi g. 5-09) using the supplied hose support (see fi g. - Page 19 INSTALLATION INSTRUCTIONS Connecting to a “T” union of the drain circuit MAKE THE CONNECTION UPLINE FROM THE SIPHON OF THE DRAIN LINE AND AT LEAST 400 mm (15-3/4”) ABOVE THE FLOOR ON WHICH THE DISHWASHER WILL BE INSTALLED. Connect the dishwasher drain hose (ref. A fi g. 5-11) to the “T” union (ref. B fi g. 5-11) of the drain circuit using a 38 to 50 mm (1-1/2 to 2”) screw clamp* (ref.
- Page 20 INSTALLATION INSTRUCTIONS Connecting to a waste disposal unit with an air gap MAKE THE CONNECTION UPLINE FROM THE SIPHON OF THE DRAIN LINE AND AT LEAST 400 mm (15-3/4”) ABOVE THE FLOOR ON WHICH THE DISHWASHER WILL BE INSTALLED. Remove the cover of the waste disposal unit (ref. A fi g. 5-12). Connect the dishwasher drain hose (ref.
- Page 21 INSTALLATION INSTRUCTIONS Connecting to the air gap (no waste disposal unit) MAKE THE CONNECTION UPLINE FROM THE SIPHON OF THE DRAIN LINE AND AT LEAST 400 mm (15-3/4”) ABOVE THE FLOOR ON WHICH THE DISHWASHER WILL BE INSTALLED. Connect the dishwasher drain hose (ref. A fi g. 5-13) to the air gap (ref. B fi g. 5-13) using the wide spring clamp (ref.
- Page 22 INSTALLATION INSTRUCTIONS Connecting to a waste disposal unit (no air gap) MAKE THE CONNECTION UPLINE FROM THE SIPHON OF THE DRAIN LINE AND AT LEAST 400 mm (15-3/4”) ABOVE THE FLOOR ON WHICH THE DISHWASHER WILL BE INSTALLED. Remove the cover of the waste disposal unit (ref. A fi g. 5-14). Connect the dishwasher drain hose (ref.
-
Page 23: Electrical Connections And Warnings
INSTALLATION INSTRUCTIONS 5 .2.2 Electrical connections and warnings CHECK THAT THE VOLTAGE AND THE FREQUENCY OF THE MAINS MATCH THE RATINGS ON THE NAME PLATE OF THE APPLIANCE POSITIONED ON THE INNER EDGE OF THE DOOR. IN THE EVENT OF DAMAGE TO THE SUPPLY CORD, HAVE IT RE- PLACED BY THE MANUFACTURER OR AN AUTHORIZED TECHNICAL SER- VICE CENTRE. -
Page 24: Commissioning
INSTALLATION INSTRUCTIONS The plug at the end of the power cord and the corresponding socket must be of the same type and must conform to current regulations governing electrical ap- pliances. The plug must be accessible after installation. Never remove the plug by pulling on the wire. - Page 25 INSTALLATION INSTRUCTIONS Fig. 5-16 Fig. 5-17 Push the dishwasher into position, taking care not to twist or crush the power cord or hoses (see fi g. 5-18). TWO PEOPLE WEARING SAFETY GLOVES ARE NEEDED TO PUSH THE DISHWASHER INTO PLACE. Fig.
-
Page 26: Procedure For Mounting The Door Panel
INSTALLATION INSTRUCTIONS 5.3.2 Procedure for mounting the door panel Mount the door panel. Place the template on the inner surface of the panel, centering it along the upper side and matching up the reference locators (ref. A fi g. 5-19); mark the position of the door hooks with a pencil (see fi g. - Page 27 INSTALLATION INSTRUCTIONS Drill holes for the panel handle using a drill with a suitable bit. Use the screwdriver to secure the door handle before hooking the panel to the dishwasher (see fi g. 5-21). N.B.: the screws are not supplied. Fig.
- Page 28 INSTALLATION INSTRUCTIONS Attach the door panel: fi t the hooks into their slots on the dishwasher and allow the panel to slide downwards and slip in to place (see fi g. 5-23). Fig. 5-23 Secure the door to the panel with the supplied screws. The panel must have a minimum thickness of 20 mm (25/32”) (see fi g.
- Page 29 INSTALLATION INSTRUCTIONS Make sure the dishwasher door, complete with panel, opens comfortably and that the base plate (ref. A fi g. 5-25) does not prevent it from opening fully. If the base plate prevents the door from opening, mark out the section to remove (see fi g.
-
Page 30: Completion Of Installation
INSTALLATION INSTRUCTIONS 5.3.3 Completion of installation Finish the cut with a fi le (see fi g. 5-27) in order to remove any burrs and/or imper- fections. Put back the base plate (see fi g. 5-28) and try to open the dishwasher door fully;... - Page 31 INSTALLATION INSTRUCTIONS Before securing the dishwasher to the adjacent units, attach the gaskets to the sides. Remove the adhesive band on the gasket (see fi g. 5-29). Fig. 5-29 Fix the gasket to the dishwasher, inserting it in the seat on the sides towards the front (see fi g.
- Page 32 INSTALLATION INSTRUCTIONS Fig. 5-31 Fig. 5-32 shows the state of the dishwasher after the above operations are per- formed. Fig. 5-32 Rev 0.0...
-
Page 33: Testing
INSTALLATION INSTRUCTIONS Tighten the supplied screws with a screwdriver; this operation defi nitively fi xes the dishwasher to the adjacent units; cover the side holes using the supplied plugs (ref. A fi g. 5-33). Fig. 5-33 Testing After installation, test the dishwasher by starting a work cycle. Check for leaks and make sure the appliance does not malfunction. - Page 34 Canada Tel 905-829.3980 Fax 905-829.3985 email marketing@euro-line-appliances.com For Service & Spares: EURO-PARTS 1.800.678.8352 Important: Please record details of your purchase below and mail or fax to AEG -----------------------------------------------------------------------------------------cut along line ------------------------------------------------------------------------------------ Name: TEL No Address: City : State: Zip Code:...
- Page 35 AEG appliances are imported and distributed in North America by Euro-Line Appliances Inc. For more information visit www.euro-line-appliances.com / www.elawest.com 871 Cranberry Court 2912 West 4th Ave Oakville, ON L6L 6J7 Vancouver, BC V6K 1R2 Canada Canada Toll Free: 1.800.421.6332 Toll Free: 1.855.352-9378...