Related Manuals for CCTV EASY SERIES H.264
Summary of Contents for CCTV EASY SERIES H.264
- Page 1 "EASY SERIES" H.264 Network Digital Video Recorder w/ Internet and Cell Phone Viewing, 320gb Hard Drive and VGA Input USER MANUAL Website: www.CCTVSecurityPros.com ...
-
Page 2: Table Of Contents
CONTENT 1 INTRODUCTION........................1.1 Main Feature ..........................3 1.2 Product features......................3 1.2.1 Parameter ..........................3 1.2.2 Basic working parameter ...................... 5 1.3 ENTIRONMENT ADAPTABILITY....................5 2 Device operation manual....................... …….. 6 2.1 Remote key instruction .......................……. 6 2.1.1 Remote control........................ -
Page 3: Introduction
1 INTRODUCTION 1.1 Main Feature Our EASY SERIES DVR is developed base on HI3511 hardware platform. EZ SERIES CSP- EZDVR4 is 4channel CIF resolution digital video recorder and EZ SERIES-EZDVR8 is 8channnel DVR. Both of them have local recording, playback, support trible code remote network surveillance, data backup, parameter setting, motion detection, I/O alarm setting, PTZ and USB mouse. -
Page 4: Network 3
Basic electricity output Linearity electricity Audio video recorded Record style simultanously Audio compression ADPCM Picture compression H.264，（VBR） / (CBR) Picture resolution CIF/HD1/D1 Streaming style ISO14496-10 Picture Audio style Video code ADPCM CIF: 384~768 Kbps HD1: proceeding rate 512~1024 Kbps D1：512~1024 and store Kbps Audio code rate... -
Page 5: Basic Working Parameter
1.2.2 Basic working parameter item parameter remark Voltage input DC 19V。 Voltage outputfor 12V（+/-0.2） 12V，1A(For D7704HT) camera Video impedance 75Ω 75Ωeach channel。 input Video output 1Vp-p 1Vp-p CVBS signal 0—2V Low voltage alarm 5V-30v Hight voltage alarm RS232 serial port, for extend use RS485 Connect to PTZ, (Pelco-D，Pelco-P) -
Page 6: Device Operation Manual
2 Device operation manual In device operation, the enter key on remote control has the same function with mouse left click. 2.1 Remote key instruction 2.1.1 Remote control Handheld IR Controller Key Functions: 【0－9】keys：During setup, number keys are used to input values. For viewing channels 1, 2, 3 and 4, use 1, 2, 3 and 4 on numeric keypad respectively. -
Page 7: Mouse Operation
： Up, Down directional keys: Move selection up and down in setup menu. ▲， ， ：Left, Right directional keys: Move cusor left or right in setup menu. 【Enter】key: During setup, select and save entry During Playback and preview, displays the channel name, text number, driver name, event sensor item and time, year/month/date, time, GPRS/GPS info. -
Page 8: Live 2
Enter into main menu: Click the right key on the live view. Click right Exit the present menu: It won’t save the settings if you click the right key to exit. Exit the playback interface: Click the right key to exit when you are playback. Click the left key to enter into the setting interface. -
Page 9: Menu Tree
2.1.3 Menu Tree You can control the DVR by a lot of menu operation. This tree will show you the menu structure and it will be in details in after chapter. Website: www.CCTVSecurityPros.com ... -
Page 10: System Operation
2.2 System Operation 2.2.1 User Login 1. START-UP Connect the DC19V/3A adapter to DVR. When start up the DVR, 【POW】LED will be on and 4 images will be display on the screen. If it has setup ignition recording or time recording, the system will record automatically and the corresponding LED will be on, the system work normally. -
Page 11: Gui Operation
2.2.2 GUI OPERATION The main menu include “SEARCH”,”RECORD”,”HDD”,”BASIC”， “ADVANCE”,and“Exit”. Remark: You must after pressing “APPLY”to make the setting for submenu valid.It will no use when exit directly.This DVR have a special feature is: when you move the mouse to everwhere, there will have the explanation information showed autoly. - Page 12 1.MONTH: It will show all the recording status in this month. Green means normal recording, Red means alarm recording, Grounding means no recording. Click any date in this frame can search the recording status of that day,the searching result will be showed in the below date frame. 2.
- Page 13 【PAUSE/STEP 】to pause and frame by frame play；Press 【Exit】to exit from playback and return to the former menu； 5. When finished playback files, it will return to the file list interface. 2. BACKUP You can use USB for backup，should insert USB device into the USB2.0 port before backup files. And it is support USB OTG.
- Page 14 CHANNEL：ON: Means the channel enable for recording. RESOLUTION：Setup resolution and code rate for recording, there are HIGEST, HIGH, NORMAL three options, corresponding to D1 、HD1、CIF resolution. QUALITY ：There are BEST, FINE ANDNORMAL three option, corresponding HIGHEST, HINGAND NORMAL data stream standard AUDIO：ON: Means enable the audio recording for all channels, OFF: Means disable audio recording REC.MODE：...
- Page 15 means alarm record, green means normal record, grounding means no record. RECORD SIZE：There are 15min, 30min, 45min, 60min four options, that means it will pack as the mode you selected Scroll to APPLY and press ENTER to save the new settings. 2.2.2.3 HDD MANAGE Move the cursor to 【HDD】（Icon highlighted when selected）,press【Enter 】to enter into the setting interface, and you can use direction keys and cursor to change the options.
-
Page 16: System Language Setup
Basic setup includes system language, time/date, security, display, video/audio and exit six options. 2.2.2.4.1 SYSTEM LANGUAGE SETUP Move cursor to select “system language” (The big icon means select ok)and press 【ENTER】to enter into the system language setup interface. System language have Chinese and English two options, you can setup the language you want in here. - Page 17 DATE: Setup system date via numeric key. DATE FORMAT: Press ENTER to switch between the date patterns, there are YY-MM-DD and MM/DD/YY two options. TIME: Setup system time via numeric key. TIME FORMAT: Press ENTER to switch between the date patterns, there are 12 HOURS and 24 HOURS two options.
- Page 18 PASSWORD：Press【APPLY 】to start or close user password. If it is “ENABLE”, you must input password when log in, otherwise, you can enter into main manu directly. USER PASSWORD：Press 【+】/【-】or numbe keys to setup user password. ADMIN PASSWORD：Press【+】/【-】or press number keys to setup admin password. 2.2.2.4.4 DISPLAY SETUP Move the cursor to【DISPLAY SETUP 】（Icon highlighted when selected）, press【Enter 】to enter into the setting interface.
- Page 19 PREVIEW：ON: Means the channel is allowed to view the live mode, OFF means not. PREVIEW TIME: ON: Means insert clock in live view, OFF means not. RECORD TIME ：ON: Means insert clock in record file, OFF means not. 2.2.2.4.5 VIDOE/AUDIO SETUP Move the cursor to【VIDEO/AUDIO SETUP】（Icon highlighted when selected），press【Enter 】to enter into setting interface.
- Page 20 Advanced Features include Alarm settings, system information, Motion detection, mobile phone monitoring, system maintenance, PTZ and network setting. 2.2.2.5.1 ALARM SETUP Move the cursor to【ALARM SETUP 】（Icon highlighted when selected），press【Enter】to enter into setting interface. I/O CHANNEL： Each channel corresponds an I/O status, that is, when an alarm triggered, it will activate the corresponding channel to start alarm recording.
- Page 21 0 second、10 seconds, 20 seconds, 40 seconds and 60 seconds ● BUZZER：buzzer calling time setup when alarm triggered: 0 second,10 seconds,20 seconds,40 seconds and 60 seconds ● POST REC.：post recording time setup: 30 seconds,1 minute,2 minutes and 5 minutes ●...
- Page 22 the motion detection for each channel.. SNESITIVITY：each channel has corresponding sensitivity setting,including four standards high,higher,medium and low, press 【Enter】key to switch MD AREA： each channel has corresponding regional motion detecting setting,move the cursor to corresponding 【setting】，press【Enter】to enter regional setting interface, red area means it have activated motion detection, transparent block means it have not activated motion detection.
- Page 23 CHANNEL: select the channel for mobile view, and press [Enter] to switch different channels. MOBLE NETWORK: Select different mobile network from the options of 3G, 2.5G and 2.75G, and press [Enter] to switch different network. 2.2.2.5.5 SYSTEM MAINTAIN Move the cursor to 【SYSTEM MAINTAIN 】...
- Page 24 DEFAULT SETTINGS: Restore all the settings as the factory setting. 2.2.2.5.6 PTZ SETUP Move the cursor to【PTZ SETUP 】（Icon highlighted when selected），press【Enter】to enter into setting interface, you can setup the parameters for each channel separately. CHANNEL: The channel of PTZ connected. PROTOCOL: select the protocol of different PTZ, there are two protocols to switch, and the default is Pelco-D BAUD RATE: select the different baud rate for your PTZ, there are 1200, 2400, 4800, and 9600...
- Page 25 Move the cursor to [NETWORK SETUP] (icon thighlitend when selected), and press 【Enter】to enter into setting interface . TYPE: There are PPPOE, DHCP & Static three options. ● STATIC Select [Static] in the type, and press [Enter] to enter into the interface as followings MEDIA PORT：transfers video data between client and device.
- Page 26 PPPOE username and password: fill the username and password of the internet service offer, and apply it and reboot the system. After rebooting, the device will save it and set the PPPOE as default network type. If succeed, the IP address will be automatically config as dynamic IP of WAN. ●...
-
Page 27: Ie Operation
DDNS: There are [ON/OFF], and if there is a DDNS service, please setup it as ON. SERVICE: There are 3 serviceS to select, 3322, dyndns, perfecteyes. HOST NAME: Input the name of the host server. USERNAME: Input in the name of the user. PASSWORD: Input the password. -
Page 28: Operation Interface
Remark: If you connect the device in WAN, the IP should be a public IP. 3.3 OPERATION INTERFACE There are Liveview, Playback and Setup options in the main interface, please press them to access it. 3.3.1 LIVE Click to enter into the interface as followings 3.3.1.1 PTZ CONTROL Change the focus, preset aperture to control the PTZ. -
Page 29: Zoom
3.3.1.1.1 ZOOM Click to zoom in and out. Click to focus Click to change the size of aperture 3.3.1.1.2 PTZ PRESET Setup preset point. You can control it via the below three buttons: 3.3.1.2 PLAY Move cursor to the icons, it will highlighted when selected Open all windows. -
Page 30: Other Operation
3.3.1.3 OTHER OPERATION 1. Select one channel at preview screen (the selected channel’s frame will be change to RED), double click left key, enter to the selected channel single screen display. 2. Click one Chanel via left key at preview screen, then click right key, will occur window shortcut Menu, see below picture You can open, shut down and start this channel’s record via shortcut menu. - Page 31 The highlighted date means that day have recording video, RED FRAME means the date is system date, click the date will search that days’ recording file list. For example, the above picture display 2008, Dec. 3 have recording video, and system date is 18 , Dec, 2008, currently search date is 17 , Dec.
- Page 32 Slow play Pause at next frame Convert H.264 file to H.avi file, click this button access into file convert setting interface, as follow. SOURCE FILE: Click to setup the H.264 file to convert to setup the directory for saving avi file After setting, click , file convert start, the convert progress bar (see below picture) will see the progress of convert.
-
Page 33: Setup
3.3.3 SETUP Click to enter into setup interface, this interface include record, alarm, PTZ, network, setting and system information six menus. 3.3.3.1 RECORD Click to enter into setup interface; you can check the parameter settings as in GUI of DVR. 3.3.3.2 ALARM Click to enter into setup interface;... -
Page 34: Ptz
3.3.3.3 PTZ Click to enter into setup interface; you can check the parameter settings as in GUI of DVR. Website: www.CCTVSecurityPros.com ... -
Page 35: Setting
3.3.3.4 NETWORK Click to enter into setup interface; you can check the parameter settings as in GUI of DVR. 3.3.3.5 SETTING Click to enter into setup interface; you can check the parameter settings as in GUI of DVR. Website: www.CCTVSecurityPros.com ... -
Page 36: Host Info
BANDWIDTH: Set the amount of bandwidth in kbps (128k、192k 、256k、384k 、512k、1024k) that you want to allocate for traffic that matches internet，this bandwidth not includes audio. FILE SAVE PATH: capture picture and recording video save path. IE login password and DST settings you can check as DVR setting. 3.3.3.6 HOST INFO Click to enter into system information interface (see below picture), this... -
Page 37: Dvr Installation Guideline
4 DVR Installation Guideline 4.1 Product Overview Product Photo The Definition of Bottons and Connectors on Front Panel Website: www.CCTVSecurityPros.com ... - Page 38 Buttons on Front Panel ＃ Button Name Description Power STANDBY POWER/OFF, boot up DVR or shutdown DVR Navigation During the setting for GUI, use these bottons for choosing differents items on menu. And also control the direction of PTZ. ENTER Confirm Control...
- Page 39 Item Connector description Physical connector DC 19V/3A POWER input Video output Two video output for connecting TV or monitor (BNC) For connectiong analog video signal input (BNC) Video input For connecting aidio signal Audio Input I/O alarm input, 4 for 4CH DVR and 8 for 8CH DVR Alarm Input I/O output for alarm Alarm Output...
- Page 40 There are 8 sets alarm input connector and 1 set output for this DVR. Alarm input is for connection IR annunciator, fog sensor. The connection diagram of DC alarm inout as following: Connection diagram of AC alarm input as following: The connection diagram of alarm output as following: Website: www.CCTVSecurityPros.com ...
-
Page 41: Hdd Installation
6. System Network Diagram 4.2 HDD Installation Please installation the HDD as the following steps: 1）Uninstall the DVR and then you will see one HDD plate as following. Website: www.CCTVSecurityPros.com ... - Page 42 2）Take out the anti-vibration mat and screws from the accessories box 3）Take off the HDD plate and then install the anti-vibration mat on the plate and then screw on it. 4）Install the HDD on HDD plate as the following photo indicate and then screws around. Website: www.CCTVSecurityPros.com ...
- Page 43 5）Fix the HDD plate on the DVR device and then cover the DVR and screw. Remark: Please format the new HDD before record. Website: www.CCTVSecurityPros.com ...