Integra DMI-40.4 Instruction Manual

Dock for iphone/ipad with airplay

Hide thumbs

Table Of Contents

Dock for iPhone

/iPad

with AirPlay

DMI-40.4

Instruction Manual

Table of Contents

Need help?

Do you have a question about the DMI-40.4 and is the answer not in the manual?

Questions and answers

Summary of Contents for Integra DMI-40.4

Page 1 Dock for iPhone ® /iPad ® with AirPlay ® DMI-40.4 Instruction Manual...
Page 2: Important Safety Instructions
Thank you for purchasing an Integra product. Please Important Safety Instructions read this manual carefully before making any connections or using this product. By following these Read these instructions. instructions, you’ll get the best audio performance Keep these instructions. and the most listening pleasure from your Integra Heed all warnings.
Page 3 Precautions is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been Recording Copyright—Unless it’s for personal use only, dropped. recording copyrighted material is illegal without the 14.
Page 4 For U.S. models FCC Caution: Any changes or modifications not expressly approved by the FCC Statement grantee of this device could void the user’s authority to Federal Communication Commission Interference operate the equipment. Statement RF exposure warning This equipment has been tested and found to comply with the This equipment must be installed and operated in accordance limits for a Class B digital device, pursuant to Part 15 of the FCC with provided instructions and the antenna(s) used for this...
Page 5 For Canadian models For European models Canada, Industry Canada (IC) Notices This Class B digital apparatus complies with Canadian ICES- 003 and RSS-210. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Page 6 Hereby, Onkyo Corporation, declares that this DMI-40.4 is Austria Netherlands in compliance with the essential requirements and other Belgium Poland relevant provisions of Directive 1999/5/EC. Bulgaria Portugal С настоящето, Onkyo Corporation, декларира, че DMI-40.4 е в съответствие със съществените Cyprus Romania изисквания...
Page 7 Con la presente Onkyo Corporation dichiara che questo Onkyo Corporation izjavlja, da je ta DMI-40.4 v skladu z DMI-40.4 è conforme ai requisiti essenziali ed alle altre bistvenimi zahtevami in drugimi relevantnimi določili disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. direktive 1999/5/ES.
Page 8: Supplied Accessories
Push Note * A Lithium Coin Battery CR2025 is loaded on the remote • The AC adapter supplied with the DMI-40.4 is control at the factory. designed exclusively for use with the DMI-40.4. Do * In catalogs and on packaging, the letter at the end of the not use it with any another device.
Page 9 Compatible iPod/iPhone/iPad models About DMI-40.4 Made for: With the Integra DMI-40.4, you can easily play the • iPod touch (1st, 2nd, 3rd and 4th generation) music stored on your Apple iPod/iPhone/iPad • iPod nano (2nd, 3rd, 4th, 5th and 6th generation) through your Integra/Onkyo amp or AV receiver and •...
Page 10 The Wi-Fi CERTIFIED Logo is a certification mark of the AirPlay, the AirPlay logo, iPad, iPhone, iPod, Wi-Fi Alliance. iPod classic, iPod nano, iPod shuffle, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. “Made for iPod”...
Page 11: Part Names
Remote control sensor Receives control signals from the remote controller. Status LED Lights up/blinks depending on the status of your DMI-40.4. See page 29 for details. Dock connector Connects to your iPod/iPhone/iPad. Wireless antenna This is the antenna for transmitting and receiving wireless signals.
Page 12 This is the analog video output jack. jack TAPE DOCK This is the jack for linked operation with RI MODE switch Integra/Onkyo amp or AV receiver equipped with jack. Connection only by cable cannot perform linked operation. Appropriate See your amp or AV receiver’s instruction manual connection by analog audio cable is also for details on changing the input display.
Page 13: Remote Controller
Selects the next song. Press and hold to fast forward. Shuffle button button Performs shuffle playback. Sets the DMI-40.4 to on or standby. Note Menu button Returns to the previous menu. • Actual operation may vary depending on your iPod/iPhone/iPad model, its generation, and / and Enter buttons firmware version.
Page 14 Some of the iPod/iPhone/iPad functions that you can control with this remote controller can also be controlled with the remote controller that came with your amp or AV receiver. Refer to the instruction manual that came with your amp or AV receiver for details.
Page 15: Aiming The Remote Controller
Relocate if necessary. • If another remote controller of the same type is used in the same room, or the DMI-40.4 is installed close to equipment that uses infrared rays, the remote controller may not work reliably.
Page 16: Replacing The Battery
Replacing the Battery Note • If the remote controller doesn’t work reliably, try The supplied remote controller uses a CR2025 type replacing the battery. battery. Always use with the same type. • If you intend not to use the remote controller for a long time, remove the battery to prevent damage Squeeze and pull to from leakage or corrosion.
Page 17 Connecting the DMI-40.4 Connect the DMI-40.4 to your Integra/Onkyo amp, AV receiver, etc. as shown below. Wall outlet Wi-Fi router Wireless signals AC adapter Optical digital audio cable Supplied AV cable Amp or AV receiver AUDIO OPTICAL White INPUT Ethernet cable...
Page 18 Note Note • To prevent dock connector damage, don’t twist • Do not place the DMI-40.4 on top of a component your iPod/iPhone/iPad when inserting or removing that gets warm or one with has air vents on top, as it, and be careful not to knock your it may interfere with that component’s cooling or...
Page 19: Network Setup
DMI-40.4, pull the Ethernet cable out after ■ Using Wi-Fi Network Login Sharing turning the power of DMI-40.4 off, and turn the power on again and make the settings. Note • To use this function, iOS version 5 or greater is Connect the iOS device connected to Wi-Fi required on the following devices.
Page 20 LED blinks in blue. Connect the DMI-40.4 to your router with an Wireless settings of the DMI-40.4 are set to the Ethernet cable. same as that of iOS device. This allows Set the DMI-40.4 power to on.
Page 21: Wireless Connection
• If Ethernet cable is being connected to the “192.168.1.1” in the browser’s Internet address DMI-40.4, pull the Ethernet cable out after (URL) field through Internet browser such as turning the power of DMI-40.4 off, and turn the ® Internet Explore power on again and make the settings.
Page 22: Web Settings
Launch Safari. WEB settings The WEB settings allow you to confirm information of Select all bookmarks from menu or bookmark the DMI-40.4, to change name, to configure network menu to display bookmark. and to update firmware. Select “Bonjour” list of collection.
Page 23: Playing Contents Via Airplay
Playing Contents via AirPlay Auto Standby Follow the procedure below to play back. The DMI-40.4 goes into standby status automatically, if it is not played back for longer than 20 minutes. When iPod/iPhone/iPad is connected, it goes into Turn on the DMI-40.4.
Page 24: System Functions
You can use the following systems by connecting the while your amp or AV receiver is on standby, your DMI-40.4 and Integra/Onkyo amp or AV receiver amp or AV receiver will turn on automatically, select equipped with jack by an...
Page 25 AV receiver. • If you do adjust the volume control on your iPod/iPhone/iPad while it’s inserted in the DMI-40.4, be careful that it’s not set too loud before you reconnect your earphones.
Page 26: Firmware Update
• Don’t unplug the cables or turn the power off during the update process. The DMI-40.4 goes into standby status once the updating completes. • The program and accompanying online documentation are furnished to you for use at your When you continue using the DMI-40.4, press...
Page 27: Restoring The Default Settings
• Make sure all plugs are pushed in all the way. DMI-40.4 goes into default setting mode. • Make sure the DMI-40.4 is connected to the correct Press the Mute button on the remote input jacks on your amp or AV receiver. If there’s no controller for two seconds.
Page 28 AV receiver, be sure to point it toward your amp or AV receiver when you want to control your iPod/iPhone/iPad. • Check the DMI-40.4’s RI MODE switch setting. • Try resetting your iPod/iPhone/iPad. Cannot connect to Wi-Fi (wireless LAN)
Page 29 The following table describes the DMI-40.4’s status. STATUS LED LED color Status — Standby Solid Lighting Orange iPod/iPhone/iPad is charging, or Network is ready. Blue (connected to network) Audio and video can be output from the component connected to Dock connector or with AirPlay.
Page 30: Specifications
Specifications Rating: DC 5 V, 3 A Power Consumption: 18 W Standby Power Consumption: 0.5 W (including supplied AC adapter) (Network ready) 4 W (including supplied AC adapter) Network: (Wi-Fi) IEEE 802.11b/g standard (Ethernet) 100 Mbps Dimensions (W × H × D): 4-3/4″...
Page 31 Memo...
Page 32 Integra Division of 18 park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 800-225-1946, 201-818-9200 Fax: 201-785-2650 http://www.integrahometheater.com Integra Division of Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY Tel: +49-8142-4401-0 Fax: +49-8142-4208-213 http://www.integra.eu Integra Division of 1301, 555 Tower, No.555 West NanJin Road, Jin an, Shanghai, China 200041, Tel: 86-21-52131366 Fax: 86-21-52130396 http://www.integra.com.cn...