Rear Panel - Behringer V-Tone GMX110 User Manual

V-TONE GMX110/GMX112/GMX210/GMX212/GMX1200H

2.2 Rear panel

(21) Connect the stereo jack connector of the provided
footswitch to the FOOTSWITCH connector. The footswitch
has several functions: it lets you switch between two
channels, and it also lets you activate/deactivate an effect.
Additionally, the tuner can also be activated using the
footswitch. To do that, keep the CHANNEL key pressed for
about 2 seconds.
(22) MIDI IN. This connector lets you remotely control your
V-TONE via MIDI. You can activate/deactivate effects or
switch between channels. You can use effect bypass via
program changes and parameter edits as well as edit the
presets via controllers (also see sections 6.3 and 7.1).
(23) You can connect two external loudspeakers (L/R) to the
LOUDSPEAKER connectors (GMX212 and GMX1200H).
The outputs deliver 60 W into 8 W per channel. For optimum
performance, please only connect loudspeakers with a
minimum impedance of 8 W each (see also section 6.2).
When these connectors are used the internal loudspeakers
are automatically disconnected.
The GMX210 features no external loudspeaker
connectors. The loudspeaker connector on the
GMX110 and GMX112 is described under (32).
(24) The PHONES connector lets you monitor the signal from
your V-TONE with standard headphones. The BEHRINGER
HP series is well suited for this, for example. When the
PHONES connector is used, the internal loudspeakers and
speaker outputs are disconnected.
(25) Those signals that are connected to the SLAVE IN
connectors are directly routed to the V-TONE's power amp.
This way, you can connect an external guitar preamp or
modeling amp (e. g. V-AMP 2 or V-AMP PRO) without using
the internal preamp on your V-TONE.
The GMX110 and GMX112 feature no SLAVE IN
connectors.
(26) You can take the stereo signal of your V-TONE at the
TAPE outputs (RCA) and record it, for example.
(27) The TAPE inputs (RCA) let you feed an additional stereo
signal into your V-TONE. You can play along to the beat of
a drum computer or play to music from a CD or MD player.
(28) You can take the stereo signal of your V-TONE at the LINE
outputs to record it or route it to a P.A. system. This output
is independent from the MASTER control and does not
render the AUX signal. Additionally, its frequency response
is corrected (speaker simulation).
The GMX110 and GMX112 feature no LINE outputs.
(29) Use the AUX IN control to adjust the volume of the signal
that is fed in via the AUX IN connectors (e. g. drum
computer, playback).
On the GMX110 and GMX112, this control is called
TAPE INPUT. It regulates the volume of the signal
fed in at the TAPE IN connectors.
(30) The AUX IN lets you feed an additional stereo signal into
the amp. This way, you can play to a backing track that
supports you on-stage but should not be audible via the
LINE outputs connecting the GMX210/GMX212 to the P.A.
system. Additionally, you can use AUX IN together with the
INSERT SEND as a parallel insert loop. To do that, connect
the INSERT SEND to the input of your effects device;
connect the AUX IN (TAPE IN on the GMX110 and GMX112)
to the output of your effects unit (the INSERT RETURN
connector should not be in use!). This way, the signal flow
in your V-TONE is not interrupted. With the AUX IN control,
you can determine the extent to which the external effects
unit alters the original signal. Keep in mind that the effects
unit should be set up to 100% effects signal (100% "wet").
6
(31) Your V-TONE features a serial insert loop that can be used
to connect external effects (e. g. a wah-wah pedal).
Connect the SEND connector on the V-TONE to the input
of your effects unit. The SEND connector is tapped into
directly before (i.e. pre) the digital signal processor (DSP)
of your V-TONE. Connect the output of your external effects
unit to the RETURN connector of your V-TONE.
You can use the INSERT SEND as a parallel output
without the effects. This is useful, for example,
when you want to record a dry guitar signal. As
long as the RETURN connector has nothing plugged
into it, the signal will not be interrupted internally.
(32) Use the SPEAKER OUT connector to connect one additional
loudspeaker to your GMX110/GMX112. This loudspeaker
should have an impedance of 4 . When this connector is
used, the internal loudspeaker is automatically muted.
Additional information about connecting an external
loudspeaker can be found in section 6.2.
(33) FUSE RETAINER/VOLTAGE SELECTOR. Please make
sure that the voltage indicated by the voltage selector
matches the local voltage before you connect the unit to
the main power supply. Always replace blown fuses with
fuses of the same type and rating. Some units feature a
fuse retainer in which a selection between 230 V and 120
V is possible. Please be aware: When using your unit
outside of Europe with 120 V, a fuse with a higher rating is
required.
(34) Power is supplied via an IEC connector. The matching
cable is provided with the unit.
(35) SERIAL NUMBER.
2. Control elements and connections