Dw Drums 2000 Series Owner's Manual

Thank you for purchasing this DW pedal. It has been designed and
manufactured to provide a lifetime of trouble-free service. Please take a
moment to familiarize yourself with the exclusive features and
operating suggestions contained in this manual in order to ensure its
optimum performance. Should you have any further questions, feel free
to contact your local authorized DW dealer.
DW Pedal 5-Year Limited Warranty
For a period of ve years from the date of purchase, Drum Workshop,
Inc. guarantees the original owner when presented with proof of
purchase, that all 2000 Series Bass Drum Pedal cast parts are free of
material and manufacturing defects. This warranty is limited to cast
parts only such as the base casting, footboard, beater hub, sprocket,
heel and cam casting. This warranty does not include moving parts
such as the spring assembly, beater ball, hex shaft, ball bearings, etc.
Moving parts have a six month warranty from the date of purchase. If
under normal playing conditions parts covered in the limited ve year
warranty fail, they will be replaced at no charge. Return the pedal to
your authorized DW dealer, or if there is not a dealer in your area,
contact DW directly. DO NOT send pedal to DW without rst receiving
a Return Authorization (RA) number. Shipping charges to DW will be
paid by the consumer.
minutes.
rst may you screws, these holding lock
unwanted prevent to lock chemical a with
Pedal Primary
Linkage
Plate Pedal
Spur
Screw Key Clamp Hoop
Nut Adjustment
Tension Spring
Clamp Hoop
Spring
Hub Rocker
Adjustment Stroke
Hub Beater
Shaft Beater
Beater Two-Way
-Don Lombardi
President, Drum Workshop, Inc
2-3 for dryer hair or gun heat a with them
chemical the loosen to order In playing. during
treated been have pedal the on screws the of
Pedal Double Pedal
Plate
Footboard
Casting
Chain
Sprocket
3450 Lunar Court - Oxnard, CA 93030 USA
linkage the
set the Loosen
the to
by pedal primary
heat to need
loosening
Some Note:
recommended
it reposition
of position
combination
the of bottom
Auxiliary
rubber provided
the Position
to nut knurled
loosen or
of base the
Heel
locking
at, a and
Base
desired the
Single
The area.
Accelerator
stroke (shorter)
drum. the
OWNER'S MANUAL
2000 Series Bass Drum Pedals
DRUM WORKSHOP INC.
www.dwdrums.com
screws.
of angle and length the adjust and linkage
screw. key side auxiliary the tighten and
pedal auxiliary the on shaft hex and casting
the to linkage the secure to key drum
Pedals)- (Double assembly
drummers. many by preferred
are settings factory The sprocket. the
and sprocket and chain the from connector
the change To stroke. the of length the
in adjusted when and, footboard the of
Adjustment-
the on Velcro non-skid and spurs adjustable
hoop. drum
the Use securely. screw key side the
hoops. drum bass manufacturers' of variety
the retighten and nut hex the release then
Tighten nut. hex locking the release to spring
at nut knurled round the loosen tension,
tension a as well as damper reduction noise
weight. the without but wood, like
attack warmer a for side felt medium curved,
screw. key hub beater the tightening
Once drum. the of center the above inches
impact and feel desired the achieve to
lighter a for back, the towards screw
hitting before travels beater the distance
key the retighten then position, desired the
the of section middle the on screws key
linkage the attach position, playing correct
beater, the Rotate screw. key the tightening
standard any or key drum provided the
linkage the adjusting and Attaching
and situations playing general most
in hole alternate an to it moving by directed
link master the remove carefully chain,
adjustment, stroke and height beater the
angle the determines chain the of length
Angle Footboard & Position Chain
crawl. drum bass prevent to pedals
in built include Pedals Drum Bass DW
Velcro- and Spurs Non-Skid
bass the to damage avoid to protector hoop
tighten and hoop the of center the on pedal
wide t a to designed is Clamp Toe DW
Clamp- Hoop
adjustment. the in
tension, desired the create to nut lock
the on down pull and assembly spring
spring the decrease or increase To mechanism.
internal an feature springs pedal drum
Tension- Spring
much attack, brighter a for side plastic
a both has Beater Two-Way standard
Surface- Playing Beater
by shaft beater the secure achieved, is height
1-2 area an or center the hit should beater
adjusted be can shaft beater the of length
Height- Beater
forward. screw the move
the move stroke (longer) heavier slightly
the vary to used be can adjustment stroke
Adjustment- Stroke
to
of
Use
for
as
the
with
The
All
The
lock
the
the
DW
hard
The
The
a For
The