Related Manuals for Dixon 539 132250
Summary of Contents for Dixon 539 132250
- Page 1 Operator and Parts Manual DIXON Blower Kit Collection System 539 132250, 539 132251 539 132252, 539 132397...
- Page 2 ©2007 HTC. All Rights Reserved. Beatrice, NE. Printed in U.S.A.
- Page 3 CONTENTS SAFETY RULES ..........................4 CARTON CONTENTS ........................7 ASSEMBLY ...........................8 OPERATION ..........................15 CUSTOMER RESPONSIBILITIES ....................16 PARTS ............................17 CONGRATULATIONS on your purchase of a new KNOW YOUR BLOWER SYSTEM collection system. It has been designed, engineered READ THIS OPERATION MANUAL AND SAFETY and manufactured to give you the best possible RULES BEFORE ASSEMBLING OR OPERATING dependability and performance.
- Page 4 SAFETY SAFE OPERATION PRACTICES FOR RIDE-ON MOWERS DANGER ! THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OB- JECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERI- OUS INJURY OR DEATH. I. GENERAL OPERATION •...
- Page 5 SAFETY SAFE OPERATION PRACTICES FOR RIDE-ON MOWERS DO NOT IV. SERVICE • Do not turn on slopes unless necessary, and • The operation of any mower can result in then, turn slowly and gradually downhill, if foreign objects thrown into the eyes, which possible.
- Page 6 SAFETY SAFE OPERATION PRACTICES FOR RIDE-ON MOWERS • NEVER allow children to operate the machine. CAUTION • Be sure the area is clear of other people before In order to prevent accidental starting when mowing. Stop machine if anyone enters the setting up, transporting, adjusting or making area.
-
Page 7: Assembly
UNPACKING INSTRUCTIONS CONTAINER CONTENTS • Remove all parts and packing materials from • • Blower Assembly Drive Pulley carton. • • Belt Shield Belt TOOLS REQUIRED • • Mounting Assembly Bag of Hardware • Drill and " drill bit - 3 bag system only •... - Page 8 ASSEMBLY INSTALLING DRIVE PULLEY 1. Remove the discharge chute from the deck. 5. Remove the bolt that secures the right hand (Deck confi guration will vary by size and model) deck pulley to the spindle. 2. Lower deck to the lowest cutting position. 6.
- Page 9 ASSEMBLY MOUNTING BLOWER ASSEMBLY INSTALLING DRIVE BELT 1. Install the front and rear mount brackets to the 1. Make sure the tension release lever is forward deck with the pin and hairpin cotter supplied with or disengaged. the kit. 2. Place the belt over the pulley on the deck. Refer to illustration for proper routing.
- Page 10 ASSEMBLY INSTALLING BELT COVERS 1. Place deck belt shield over spindle, aligning hole TAP SCREW with bolt on belt shield standoff. 2. Attach with wing nut to standoff and use tap DECK BELT SHIELD screw from kit to attach the other side of the belt shield to the deck.
- Page 11 ASSEMBLY 3. Install the bagger mount tube from the mount kit. INSTALLING MIDDLE CHUTE MOUNT STRAP 1. Place middle chute over the top end of the blower assembly. 2. Latch middle chute to blower assembly. BLOWER ASSEMBLY MIDDLE CHUTE MOUNT STRAP MOUNT TUBE RAM MOUNT INSTALLING BAGGER MOUNT...
- Page 12 ASSEMBLY INSTALLING WEIGHT KITS INSTALLING CHUTE SUPPORT Units with cast weight 3 Bin System only 1. Bolt one cast weight and two weight brackets 1. Position upper chute support against bagger together using four 2¾" bolts and four nuts. inlet, fl ush at outer edges. See Illlustration. 2.
- Page 13 ASSEMBLY MOUNTING COVER ASSEMBLY TO SUPPORT ASSEMBLY CAUTION NOTE: For ease of assembly, you may wish assis- DO NOT operate mower with grass tance from another person for mounting the cover catcher, unless the front weights are assembly to mower. installed.
-
Page 14: Operation
OPERATION TIPS FOR IMPROVED BAGGING OPERATION • Avoid cutting wet grass or mowing in the Follow the mower operation instructions in the morning while the dew is still heavy. Grass mower operator’s manual. clippings collected under these conditions tend When utilizing the grass catcher on a lawn where to be sticky and adhere to the walls of the fl... -
Page 15: Customer Responsibilities
CUSTOMER RESPONSIBILITIES GENERAL RECOMMENDATIONS STORAGE Always observe safety rules when performing any When grass catcher is to be stored for a period maintenance. of time, clean it thoroughly, remove all dirt, grass, leaves, etc. Store in a clean, dry place. •... -
Page 16: Parts
PARTS... - Page 17 PARTS ITEM PART NO. QTY. DESCRIPTION ITEM PART NO. QTY. DESCRIPTION 539 108088 ..1 ..LATCH, HOOD 539 108081 ..1 ..SCREW, SPEC 10-14 x ½ 539 108089 ..1 ..PLATED, WELD NUT 539 108082 ..1 ..BAG DUMP INDICATOR 539 108141 ..1 ..
- Page 18 PARTS BAG ASSEMBLY 960 730019 14 13...
- Page 19 PARTS ITEM PART NO. QTY. DESCRIPTION ITEM PART NO. QTY. DESCRIPTION 532 192709 ..1 ..SCREEN, COVER 12.. 539 976977 ..8 ..NUT, #10-24, CROWNLOCK 532 195373 ..1 ..COVER 13.. 539 990627 ..2 ..HCS, -18 X 1¼, GR 5 539 976952 ..6 ..
- Page 20 PARTS THIS SIDE TOWARD BEARING 48 41 TORQUE TO 30 LBS 50" Deck 60" Deck...
- Page 21 PARTS ITEM PART NO. QTY. DESCRIPTION ITEM PART NO. QTY. DESCRIPTION 539 101977 ..1 ..TRACTION SPRING 34.. 539 130337 ..1 ..ARM, IDLER 539 976952 ..1 ..SCREW 10-24 x .625 RD 35.. 539 130338 ..1 ..ARM, TENSION 539 104411 ..1 ..
- Page 22 PARTS...
- Page 23 PARTS ITEM PART NO. QTY. DESCRIPTION ITEM PART NO. QTY. DESCRIPTION 539 132056 ..1 ..SHIELD, BELT, 44" 18.. 539 990861 ..4 ..RHSB, -16 x 1¾ 539 132063 ..1 ..SHIELD, BELT, 50" 19.. 539 990645 ..2 ..RHSB, -16 x 1 539 132070 ..1 ..
- Page 24 PARTS WEIGHT KIT 44"...
- Page 25 PARTS ITEM PART NO. QTY. DESCRIPTION ITEM PART NO. QTY. DESCRIPTION 539 106492 ..4 ..HCS -16 x 2¾ 539 111587 ..1 ..CAST WEIGHT 539 991126 ..4 ..HCS -16 x 3¾ 539 114898 ..2 ..WEIGHT BRACKET 539 976979 ..8 ..
- Page 26 PARTS WEIGHT KIT 50"...
- Page 27 PARTS ITEM PART NO. QTY. DESCRIPTION ITEM PART NO. QTY. DESCRIPTION 539 102612 ..4 ..HCS -16 x 2¾ GR 5 539 113232 ..3 ..WEIGHT PLATE 539 976949 ..4 ..HCS -16 x 1¾ GR 5 539 114898 ..2 ..WEIGHT BRACKET 539 976979 ..8 ..
- Page 28 539 132264 R1 12/19/07...
Need help?
Do you have a question about the 539 132250 and is the answer not in the manual?
Questions and answers