Page 1 READ THIS MANUAL CAREFULLY! It contains important safety information. OWNER’S MANUAL YFM45FXV WARNING This ATV should not be ridden by anyone under 16 years of age. LIT-11626-19-42 3C2-F8199-10...
Page 2 EBU00776...
Page 3 Yamaha experience in the production of fine sporting, touring, and pacesetting racing machines. With the purchase of this Yamaha, you can now appreciate the high degree of crafts- manship and reliability that have made Yamaha a leader in these fields.
Page 4 EBU00801 IMPORTANT MANUAL INFORMATION FAILURE TO FOLLOW THE WARNINGS CONTAINED IN THIS MANUAL CAN RESULT IN SE- RIOUS INJURY OR DEATH. Particularly important information is distinguished in this manual by the following notations: The Safety Alert Symbol means ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Failure to follow WARNING instructions could result in severe WARNING...
Page 5 Please check your local riding laws and regulations before operating this ATV. EBU01067 YFM45FXV OWNER’S MANUAL ©2005 by Yamaha Motor Corporation, AFFIX DEALER U.S.A. 1st edition, June 2005 LABEL HERE All rights reserved. Any reprinting or...
Page 6: Table Of Contents
EBU00014 Indicator and warning lights .....4-2 WARNING Speedometer unit ......4-3 Indicates a potential hazard that could Handlebar switches ......4-4 result in serious injury or death. Throttle lever ........4-7 Speed limiter ........4-8 Front brake lever......4-9 CONTENTS Brake pedal and rear brake lever ..........4-9 Drive select lever ......4-10 LOCATION OF THE WARNING...
Page 7 Final gear oil........5-6 RIDING YOUR ATV ......7-1 Differential gear oil ......5-6 Getting to know your ATV ....7-3 Coolant..........5-7 Ride with care and good Throttle lever ........5-7 judgement........7-4 Fittings and fasteners...... 5-8 Be careful where you ride....7-16 Lights..........
Page 8 Removing and installing cowlings Front brake lever free play.....8-44 and panels........8-6 Adjusting the rear brake lever and Engine oil and oil filter cartridge ..8-14 brake pedal ........8-45 Final gear oil ........8-19 Adjusting the rear brake light Differential gear oil replacement ... 8-22 switch ...........8-47 Cooling system......
Page 9 CLEANING AND STORAGE.... 9-1 A. Cleaning........9-1 B. Storage ........9-3 SPECIFICATIONS......10-1 NOISE REGULATION....11-1 MAINTENANCE RECORD .... 12-1 ATV LIMITED WARRANTY.... 13-1 YAMAHA EXTENDED SERVICE (Y.E.S.) ........... 14-1...
Page 10: Location Of The Warning And Specification Labels
EBU00464 L OCATION OF THE WARNING AND SPECIFICATION LABELS...
Page 11 Read and understand all of the labels on your machine. They contain important information for safe and proper operation of your ATV. Never remove any labels from your ATV. If a label becomes difficult to read or comes off, a replacement label is available from your Yamaha dealer.
Page 12 WARNING UNDER Operating this ATV if you are under the age of 16 increases your chance of severe injury or death. NEVER operate this ATV if you are under age 16. YAMAHA 4XE-F415A-00...
Page 14: Safety Information
EBU13361 SAFETY INFORMATION AN ATV IS NOT A TOY AND CAN BE HAZARDOUS TO OPERATE. An ATV handles differently from other vehicles including motorcycles and cars. A collision or rollover can occur quickly, even during routine maneuvers such as turning and riding on hills or over obstacles, if you fail to take proper precautions.
Page 15 Never operate an ATV without wearing an approved motorcycle helmet that fits properly. You should also wear eye protection (goggles or face shield), gloves, boots, a long-sleeved shirt or a jacket, and long pants. Never consume alcohol or drugs before or while operating this ATV. Never operate at speeds too fast for your skills or the conditions.
Page 16 Always follow proper procedures for climbing hills as described in this manual. Check the ter- rain carefully before you start up any hill. Never climb hills with excessively slippery or loose surfaces. Shift your weight forward. Never open the throttle suddenly. Never go over the top of a hill at high speed.
Page 17 Always be careful when skidding or sliding. Learn to safely control skidding or sliding by prac- ticing at low speeds and on level, smooth terrain. On extremely slippery surfaces, such as ice, go slowly and be very cautious in order to reduce the chance of skidding or sliding out of con- trol.
Page 18 WARNING When transporting the ATV in another vehicle, be sure it is kept upright and POTENTIAL HAZARD that the fuel cock is in the “OFF” posi- Improper handling of gasoline. tion. Otherwise, fuel may leak out of the WHAT CAN HAPPEN carburetor or fuel tank.
Page 19 WARNING POTENTIAL HAZARD Starting or running the engine in a closed area. WHAT CAN HAPPEN Exhaust fumes are poisonous and may cause loss of consciousness and death within a short time. HOW TO AVOID THE HAZARD Always operate your ATV in an area with adequate ventilation.
Page 20: Description And Machine Identification
EBU00032 D ESCRIPTION AND MACHINE IDENTIFICATION 1. Spark arrester 15. Engine oil dipstick 2. Tail/brake light 16. Oil filter cartridge 3. Spark plug 17. Coolant reservoir 4. Rear brake fluid reservoir 18. V-belt cooling duct check hose 5. Radiator cap 19.
Page 21: Identification Number Records
This number can be used for ordering a new when ordering spare parts from a Yamaha key. dealer or for reference in case the vehicle is stolen.
Page 22: Vehicle Identification Number
Record the information on this la- bel in the space provided. This information will be needed to order spare parts from your Yamaha dealer. 1. Vehicle identification number NOTE: The vehicle identification number is used to 1.
Page 23: Control Functions
EBU00039 C ONTROL FUNCTIONS WARNING Indicates a potential hazard that could result in serious injury or death. EBU09420 Main switch Functions of the respective switch positions are as follows: 1. Main switch The engine can be started only at this position and the headlights and taillight come on when the light switch is on.
Page 24: Indicator And Warning Lights
EBU08020 EBU00860 Indicator and warning lights Coolant temperature warning light “ ” When the coolant temperature reaches a specified level, this light comes on to warn that the coolant temperature is too hot. If the light comes on during operation, stop the en- gine as soon as it is safe to do so and allow the engine to cool down for about 10 minutes.
Page 25: Speedometer Unit
EBU12500 EBU26181 Reverse indicator light “R” Speedometer unit This indicator light comes on when the drive select lever is in the “R” position. EBU00609 Park indicator light “P” This indicator light comes on when the drive select lever is in the “P” (park) position. EBU06050 Four-wheel-drive indicator light “...
Page 26: Handlebar Switches
EBU00053 Odometer and tripmeter modes Handlebar switches Pushing the “SELECT” button switches the display between the odometer mode “ODO” and the tripmeter mode “TRIP” in the following order: ODO→TRIP→ODO To reset the tripmeter, select it by pushing the “SELECT” button, and then push the “SE- LECT”...
Page 27 EBU00607 Start switch “ ” CAUTION: The starter motor cranks the engine when this Do not use the headlights with the engine switch is pushed. turned off for more than thirty minutes. The battery may discharge to the point CAUTION: that the starter motor will not operate See starting instructions prior to starting properly.
Page 28 WARNING POTENTIAL HAZARD Changing from 2WD to 4WD or from 4WD to 2WD while the ATV is moving. WHAT CAN HAPPEN The ATV handles differently in 2WD than in 4WD in some circumstances. Changing from 2WD to 4WD or from 4WD to 2WD while moving may cause 1.
Page 29: Throttle Lever
Check the operation of the throttle lever before you start the engine. If it does not work smoothly, check for the cause. Correct the problem before riding the ATV. Consult a Yamaha dealer if you 1. Throttle lever can’t find or solve the problem yourself.
Page 30: Speed Limiter
EBU01159 Speed limiter WARNING The speed limiter keeps the throttle from fully POTENTIAL HAZARD opening, even when the throttle lever is Improper adjustment of the speed limit- pushed to the maximum. Turning in the ad- er and throttle. justing screw limits the maximum engine pow- WHAT CAN HAPPEN er available and decreases the maximum The throttle cable could be damaged.
Page 31: Front Brake Lever
EBU00070 Front brake lever The front brake lever is located on the right handlebar. Pull it toward the handlebar to ap- ply the front brake. 1. Brake pedal 1. Front brake lever EBU00732 Brake pedal and rear brake lever The brake pedal is located on the right side of the ATV and the rear brake lever is located on the left handlebar.
Page 32: Drive Select Lever
EBU15200 EBU00092 Drive select lever Fuel tank cap The drive select lever is used to shift your ma- Remove the fuel tank cap by turning it coun- chine into the forward, neutral, reverse and terclockwise. park positions. (Refer to page 6-4 for the drive select lever operation.) 1.
Page 33: Fuel Cock
EBU00093 Fuel cock OFF Position The fuel cock supplies fuel from the fuel tank to the carburetor. The fuel cock has three positions. OFF: With the lever in this position fuel will not flow. Always turn the lever to this position when the engine is not running.
Page 34: Starter (Choke)
EBU00095 Starter (choke) “ ” RES Position Starting a cold engine requires a richer air-fuel mixture. A separate starter circuit supplies this mixture. Move in direction a to turn on the starter (choke). Move in direction b to turn off the starter (choke).
Page 35: Seat
EBU26200 Seat To remove the seat, push the seat lock lever backward and pull up the seat at the rear. 1. Seat lock lever 1. Seat 4-13...
Page 36: Storage Compartment
EBU26230 To install the seat, insert the projections on Storage compartment the front of the seat into the seat holders and Maximum load limit: 2.0 kg (4 lb) push down on the seat at the rear. NOTE: The storage compartment is located under Make sure that the seat is securely fitted.
Page 37: Front Shock Absorber Adjustment
EBU01104 Front shock absorber adjustment The spring preload can be adjusted to suit the rider’s weight and riding conditions. Adjust the spring preload as follows. To increase the spring preload, turn the ad- justing ring in direction a. To decrease the spring preload, turn the ad- justing ring in direction b.
Page 38 NOTE: WARNING A special wrench can be obtained at a POTENTIAL HAZARD Yamaha dealer to make this adjustment. Improper shock absorber adjustment. WHAT CAN HAPPEN Standard position: 2 Uneven adjustment can cause poor 1 - Minimum (soft) handling and loss of stability, which 5 - Maximum (hard) could lead to an accident.
Page 39: Rear Shock Absorber Adjustment
Rear shock absorber adjustment A special wrench can be obtained at a The spring preload can be adjusted to suit the Yamaha dealer to make this adjustment. rider’s weight and riding conditions. Adjust the spring preload as follows: Standard position: 2 To increase the spring preload, turn the ad- justing ring in direction a.
Page 40 EBU00112 WARNING Indicates a potential hazard that could result in serious injury or death. 4-18...
Page 41: Pre-Operation Checks
P RE-OPERATION CHECKS Before using this machine, check the following points: ITEM ROUTINE PAGE • Check operation, lever free play, fluid level and fluid leakage. 5-2–5-3, 8-40, Front brake • Fill with DOT 4 brake fluid if necessary. 8-42–8-44 • Check operation, lever free play, fluid level and fluid leakage. 5-2–5-3, 8-41–8-43, Rear brake •...
Page 42: Front And Rear Brakes
Always follow the inspection and main- and there should be a firm feeling when the tenance procedures and schedules de- brakes are applied. If not, have a Yamaha scribed in the Owner’s Manual. dealer inspect the brake system. Brake fluid level Check the brake fluid level.
Page 43 If problem cannot be corrected by the ad- the brakes do not provide proper braking per- justment procedures provided in this formance, inspect the brake pads for wear. manual, have a Yamaha dealer check for (See pages 8-40–8-41.) the cause.
Page 44: Fuel
EBU01085 Fuel Your Yamaha engine has been designed to Make sure there is sufficient gasoline in the use regular unleaded gasoline with a pump tank. octane number ([R+M]/2) of 86 or higher, or research octane number of 91 or higher. If...
Page 45 Fuel can spill, which can cause a fire hol containing methanol is not recommended and severe injury. by Yamaha because it may cause fuel system Fuel expands when it heats up. If the damage or vehicle performance problems. fuel tank is overfilled, fuel could spill out due to heat from the engine or the sun.
Page 46: Engine Oil
EBU10842 EBU00493 Engine oil Final gear oil Make sure the engine oil is at the specified Make sure the final gear oil is at the specified level. Add oil as necessary. (See pages 8-14– level. Add oil as necessary. (See pages 8-19– 8-19.) 8-22 for details.) CAUTION:...
Page 47: Coolant
Check to see that the throttle lever operates (up to the maximum level mark): correctly. It must open smoothly and spring 0.25 L (0.22 Imp qt, 0.26 US qt) back to the idle position when released. Have a Yamaha dealer repair as necessary for proper operation.
Page 48: Fittings And Fasteners
Always check the tightness of chassis fittings WARNING and fasteners before a ride. Take the machine POTENTIAL HAZARD to a Yamaha dealer or refer to the Service Operating this ATV with improper tires, Manual for correct tightening torque. or with improper or uneven tire pres- sure.
Page 49 2. The tires should be set to the rec- 4. Use no more than the following ommended pressure: pressures when seating the tire Recommended tire pressure beads. Front 40 kPa (0.40 kgf/cm , 5.8 psi) Front 250 kPa (2.5 kgf/cm , 36 psi) Rear 40 kPa (0.40 kgf/cm , 5.8 psi)
Page 50: How To Measure Tire Pressure
EBU00159 How to measure tire pressure Use the low-pressure tire gauge. NOTE: The low-pressure tire gauge is included as standard equipment. Make two measure- ments of the tire pressure and use the second reading. Dust or dirt in the gauge could cause the first reading to be incorrect.
Page 51: Tire Wear Limit
EBU00160 Tire wear limit When the tire groove decreases to 3 mm (0.12 in) due to wear, replace the tire. a. Tire wear limit 5-11...
Page 52: Operation
2. Turn the fuel cock to “ON”. there is a control or function you do not 3. Turn the main switch to “ON” and the en- understand, ask your Yamaha dealer. gine stop switch to “ ”. 4. Shift the drive select lever into the neutral...
Page 53 25°C (80°F) and warm engine does not come on, ask a Yamaha dealer start position. to inspect its electric circuit. The engine can be started in any gear if the rear brake lever is applied. However, it is recommended to shift into neutral or park before starting the engine.
Page 54: Starting A Warm Engine
NOTE: CAUTION: If the engine fails to start, release the start See the “Engine break-in” section prior to switch, then push the start switch again. operating the engine for the first time. Pause a few seconds before the next attempt. Each cranking should be as short as possible to preserve battery energy.
Page 55: Drive Select Lever Operation And Reverse Driving
EBU15210 Drive select lever operation and reverse driving CAUTION: Before shifting, you must stop the ATV and return the throttle lever to the closed position, otherwise the transmission may be damaged. Shifting: Neutral to Forward 1. Bring the ATV to a complete stop and re- 1.
Page 56 If the light does not the drive select lever along the shift come on, ask a Yamaha dealer to inspect guide. the electrical circuit. Due to the synchronizing mechanism in the engine, the light may not come on un- til the ATV starts moving.
Page 57 5. Open the throttle lever gradually and con- tinue to watch to the rear while backing. WARNING POTENTIAL HAZARD Improperly operating in reverse. WHAT CAN HAPPEN You could hit an obstacle or person be- hind you, resulting in serious injury. HOW TO AVOID THE HAZARD When you shift into reverse, make sure there are no obstacles or people behind...
Page 58: Engine Break-In
If any abnormality is noticed during this peri- brand new, you must not put an excessive od, consult a Yamaha dealer. load on it for the first several hours of running. During the first 20 hours, the various parts in 0–10 hours:...
Page 59: Parking
EBU00612 10–20 hours: Parking Avoid prolonged operation above 3/4 throttle. When parking, stop the engine and shift the Rev the machine freely but do not use full drive select lever into the park position, then throttle at any time. turn the fuel cock to the “OFF” position. After break-in: Avoid prolonged full throttle operation.
Page 60: Parking On A Slope
EBU06151 Parking on a slope 1. Bring the machine to a stop by applying the brakes. WARNING 2. Stop the engine. POTENTIAL HAZARD 3. With the brake pedal applied, shift the Parking on a hill or other incline. drive select lever to the park position “P”. WHAT CAN HAPPEN The ATV could roll out of control, in- creasing the chance of an accident.
Page 61: Accessories And Loading
Choose only accessories designed for your dlebars which could make steering difficult, ATV. Your Yamaha dealer has a variety of an accessory that limits your ability to move genuine Yamaha accessories. Other ac-...
Page 62 EBU26240 Loading Tie down cargo securely to the carriers. As originally equipped, this ATV is not de- Make sure cargo in the trailer cannot move signed to carry cargo or tow a trailer. If you around. A shifting load can cause an acci- choose to add accessories so that you can dent.
Page 63 WARNING POTENTIAL HAZARD Overloading this ATV or carrying or tow- ing cargo improperly. WHAT CAN HAPPEN Could cause changes in vehicle han- dling which could lead to an accident. HOW TO AVOID THE HAZARD Never exceed the stated load capacity for this ATV.
Page 64 EBU26210 WARNING Indicates a potential hazard that could result in serious injury or death. 6-13...
Page 65: Riding Your Atv
R iding Your...
Page 66: Getting To Know Your Atv
WARNING Indicates a potential hazard that could result in serious injury or death. the operation of the controls. Pay particular at- GETTING TO KNOW YOUR ATV tention to the safety information on pages This ATV is intended for recreational use by 2-1–2-6.
Page 67: Ride With Care And Good Judgement
JUDGEMENT Beginning and inexperienced operators should complete the certified training Get training if you are inexperienced. course offered by Yamaha. They should Beginners should get training from a certified then regularly practice the skills learned instructor. in the course and the operating tech- Become familiar with this ATV at slow speeds niques described in this Owner’s Manu-...
Page 68 Not recommended for children under 16 years of age. WARNING POTENTIAL HAZARD Failure to follow the age recommenda- tions for this ATV. WHAT CAN HAPPEN Use by children of ATVs that are not rec- ommended for their age can lead to se- vere injury or death of the child.
Page 69 This ATV is designed to carry operator and cargo only – passengers prohibited. WARNING POTENTIAL HAZARD Carrying a passenger on this ATV. WHAT CAN HAPPEN Greatly reduces your ability to balance and control this ATV. Could cause an accident, resulting in harm to you and/ or your passenger.
Page 70 Apparel Operating without protective clothing WARNING increases your chances of severe injury in the event of an accident. POTENTIAL HAZARD HOW TO AVOID THE HAZARD Operating this ATV without wearing an Always wear an approved motorcycle approved motorcycle helmet, eye pro- helmet that fits properly.
Page 71 Do not operate after consuming alcohol or WARNING drugs. POTENTIAL HAZARD Operator’s performance capability is reduced Operating this ATV after consuming al- by the influence of alcohol or drugs. cohol or drugs. WHAT CAN HAPPEN Could seriously affect your judgment. Could cause you to react more slowly.
Page 72 Pre-operation checks WARNING Always perform the pre-operation checks list- POTENTIAL HAZARD ed on page 5-1 before riding for safety and Operating this ATV with improper tires, proper care of the ATV. or with improper or uneven tire pres- WARNING sure. POTENTIAL HAZARD WHAT CAN HAPPEN Failure to inspect the ATV before oper-...
Page 73 Speed limiter WARNING For riders inexperienced with this model, this Indicates a potential hazard that could model is equipped with a speed limiter in the result in serious injury or death. throttle lever housing. The speed limiter limits the power and top speed of the ATV. Turning Do not operate at speeds too fast for your the adjusting screw in decreases the top skills or the conditions.
Page 74 Loading and accessories WARNING As originally equipped, this ATV is not de- POTENTIAL HAZARD signed to carry cargo or tow a trailer. If you Overloading this ATV or carrying or tow- choose to add accessories so that you can ing cargo improperly. carry cargo or tow a trailer, you must use WHAT CAN HAPPEN common sense and good judgment.
Page 75 During operation WARNING Always keep your feet on the footboards dur- POTENTIAL HAZARD ing operation. Otherwise your feet may con- Removing hands from handlebars or tact the rear wheels. feet from footboards during operation. WHAT CAN HAPPEN Removing even one hand or foot can re- duce your ability to control the ATV or could cause you to lose your balance and fall off of the ATV.
Page 76 Avoid wheelies and jumping. You may lose control of the ATV or overturn. WARNING POTENTIAL HAZARD Attempting wheelies, jumps, and other stunts. WHAT CAN HAPPEN Increases the chance of an accident, in- cluding an overturn. HOW TO AVOID THE HAZARD Never attempt stunts, such as wheelies or jumps.
Page 77 Never modify this ATV through improp- er installation or use of accessories. All parts and accessories added to this ve- hicle should be genuine Yamaha or equivalent components designed for use on this ATV and should be installed and used according to instructions. If you have questions, consult an autho- rized ATV dealer.
Page 78 Exhaust system Do not touch the hot exhaust system. The exhaust system on the ATV is very hot Do not park the ATV in a place where during and following operation. To prevent others might be likely to touch it. burns, avoid touching the exhaust system.
Page 79: Be Careful Where You Ride
BE CAREFUL WHERE YOU RIDE This ATV is designed for off-road use only. Riding on paved surfaces can cause loss of control. WARNING POTENTIAL HAZARD Operating this ATV on paved surfaces. WHAT CAN HAPPEN ATVs are designed for off-road use only. Paved surfaces may seriously affect handling and control of the ATV, and may cause the vehicle to go out of con-...
Page 80 Do not ride on any public road, street, or high- way. Riding on public roads can result in collisions with other vehicles. WARNING POTENTIAL HAZARD Operating this ATV on public streets, roads or highways. WHAT CAN HAPPEN You can collide with another vehicle. HOW TO AVOID THE HAZARD Never operate this ATV on any public street, road or highway, even a dirt or...
Page 81 Know the terrain where you ride. Ride cau- tiously in unfamiliar areas. Stay alert for holes, rocks, or roots in the terrain, and oth- er hidden hazards which may cause the ATV to upset. WARNING POTENTIAL HAZARD Failure to use extra care when operating this ATV on unfamiliar terrain.
Page 82 WARNING POTENTIAL HAZARD Failure to use extra care when operating on excessively rough, slippery or loose terrain. WHAT CAN HAPPEN Could cause loss of traction or vehicle control, which could result in an acci- dent, including an overturn. HOW TO AVOID THE HAZARD Do not operate on excessively rough, slippery or loose terrain until you have learned and practiced the skills neces-...
Page 83 When riding in an area where you might not WHAT CAN HAPPEN easily be seen, such as desert terrain, mount You could be in a collision. You could a caution flag on the ATV. DO NOT use the be injured. flag pole bracket as a trailer hitch.
Page 84 Select a large, flat area off-road to become fa- With the engine idling, return the starter miliar with your ATV. Make sure that this area (choke) to the closed position, and shift the is free of obstacles and other riders. You drive select lever into the forward position.
Page 85: Turning Your Atv
TURNING YOUR ATV HOW TO AVOID THE HAZARD To achieve maximum traction while riding off- Always follow proper procedures for road, the two rear wheels are mounted solidly turning as described in this Owner’s on one axle and turn together at the same Manual.
Page 86 Once you have learned this technique you should be able to perform it at higher speeds or in tighter curves. Improper riding procedures such as abrupt throttle changes, excessive braking, incorrect body movements, or too much speed for the sharpness of the turn may cause the ATV to tip.
Page 87: Climbing Uphill
CLIMBING UPHILL HOW TO AVOID THE HAZARD Use proper riding techniques to avoid vehicle Never operate the ATV on hills too steep overturns on hills. Be sure that you can ma- for the ATV or for your abilities. Practice neuver your ATV well on flat ground before at- on smaller hills before attempting large tempting any incline and then practice riding hills.
Page 88 WARNING An obstacle, a sharp drop, or another vehicle or person could be on the other POTENTIAL HAZARD side of the hill. Climbing hills improperly. WHAT CAN HAPPEN Could cause loss of control or cause the ATV to overturn. HOW TO AVOID THE HAZARD Always follow proper procedures for climbing hills as described in this Own- er’s Manual.
Page 89 If you are climbing a hill and you find that you WARNING have not properly judged your ability to make POTENTIAL HAZARD it to the top, you should turn the ATV around Improperly crossing hills or turning on while you still have forward motion (provided hills.
Page 90 When crossing the side of a hill: Always follow proper procedures as de- scribed in the Owner’s Manual. Avoid hills with excessively slippery or loose surfaces. Shift your weight to the uphill side of the ATV. 7-27...
Page 91 If your ATV has stalled or stopped and you and rear brakes gradually, or dismount the believe you can continue up the hill, restart ATV immediately on the uphill side. carefully to make sure you do not lift the front WARNING wheels which could cause you to lose control.
Page 92 If you begin rolling backwards: Keep weight uphill. 2WD: Never apply the rear brake while rolling backwards. Apply the front brake. When fully stopped, shift to the parking position “P”. 4WD: Apply both front and rear brakes gradually. When fully stopped, shift to the parking position “P”.
Page 93: Riding Downhill
RIDING DOWNHILL When this ATV is in 4WD, all wheels (front When riding your ATV downhill, shift your and rear) are interconnected by the drive weight as far to the rear and uphill side of the train. This means that applying either the front ATV as possible.
Page 94 WARNING POTENTIAL HAZARD Going down a hill improperly. WHAT CAN HAPPEN Could cause loss of control or cause the ATV to overturn. Always follow proper procedures for go- ing down hills as described in this Own- er’s Manual. Note: a special technique is required when braking as you go down a hill.
Page 95: Crossing A Slope
CROSSING A SLOPE WARNING Traversing a sloping surface on your ATV re- POTENTIAL HAZARD quires you to properly position your weight to Improperly crossing hills or turning on maintain proper balance. Be sure that you hills. have learned the basic riding skills on flat WHAT CAN HAPPEN ground before attempting to cross a sloping Could cause loss of control or cause the...
Page 96 7-33...
Page 97: Crossing Through Shallow Water
CROSSING THROUGH SHALLOW WATER Remember that wet brakes may have re- The ATV can be used to cross slow moving, duced stopping ability. Test your brakes shallow water of up to a maximum of 35 cm after leaving water. If necessary, apply (14 inches) in depth.
Page 98 Test your brakes after leaving the water. Do CAUTION: not continue to ride your ATV without verifying After riding your ATV in water, be sure to that you have regained proper braking ability. drain the trapped water by removing the check hose at the bottom of the air filter case, the V-belt cooling duct check hose, the drive select lever box check hose and...
Page 99 1. V-belt cooling duct check hose (left front side of ATV) 1. Storage compartment drain plug (× 2) 1. Drive select lever box check hose 1. V-belt case drain plug 7-36...
Page 100: Riding Over Rough Terrain
RIDING OVER ROUGH TERRAIN WARNING Riding over rough terrain should be done with POTENTIAL HAZARD caution. Look out for obstacles which could Improperly operating over obstacles. cause damage to the ATV or could lead to an WHAT CAN HAPPEN upset or accident. Be sure to keep your feet Could cause loss of control or a colli- firmly mounted on the footboards at all times.
Page 101: Sliding And Skidding
SLIDING AND SKIDDING If the rear wheels of your ATV start to slide Care should be used when riding on loose or sideways, control can usually be regained (if slippery surfaces since the ATV may slide. If there is room to do so) by steering in the direc- unexpected and uncorrected, sliding could tion of the slide.
Page 102 With practice, over a period of time, skill at WARNING controlled sliding can be developed. The ter- POTENTIAL HAZARD rain should be chosen carefully before at- Skidding or sliding improperly. tempting such maneuvers, since both stability WHAT CAN HAPPEN and control are reduced. Bear in mind that You may lose control of this ATV.
Page 103: What To Do If
WHAT TO DO IF ... If your ATV starts to slide sideways: This section is designed to be a reference Steer in the direction of the slide if you have guide only. Be sure to read each section on the room. Applying the brakes or accelerat- riding techniques completely.
Page 104 If your ATV is traversing a sloping surface: Be sure to ride with your weight positioned towards the uphill side of the ATV to main- tain proper balance. If the ATV starts to tip, steer down the hill (if there are no obstacles in your way) to regain balance.
Page 105: Periodic Maintenance And Adjustment
EBU00515 P ERIODIC MAINTENANCE AND Have a Yamaha dealer perform service if ADJUSTMENT you are not familiar with machine ser- vice. Periodic inspection, adjustment and lubrica- tion will keep your machine in the safest and EBU14510 most efficient condition possible. Safety is an Owner’s manual and tool kit...
Page 106 HOW TO AVOID THE HAZARD during a service operation requiring one, take Never modify this ATV through improp- your machine to a Yamaha dealer to check er installation or use of accessories. All the torque settings and adjust them as neces- parts and accessories added to this ve- sary.
Page 107: Periodic Maintenance Chart For The Emission Control System
ATV isn’t used for a long period of time, the month maintenance intervals should be followed. Items marked with an asterisk should be performed by a Yamaha dealer as they require special tools, data and technical skills.
Page 108: General Maintenance And Lubrication Chart
EBU15720 General maintenance and lubrication chart INITIAL EVERY month Whichever ITEM ROUTINE comes first 1,300 2,500 2,500 5,000 (mi) (200) (800) (1,600) (1,600) (3,200) hours • Check coolant leakage. Cooling system • Repair if necessary. • Replace coolant every 24 months. •...
Page 109 INITIAL EVERY month Whichever ITEM ROUTINE comes first 1,300 2,500 2,500 5,000 (mi) (200) (800) (1,600) (1,600) (3,200) hours Engine mount* • Check for cracks or damage. • Check operation. Axle boots* • Replace if damaged. • Check all chassis fittings and fasteners. Fittings and fasteners* •...
Page 110: Removing And Installing Cowlings And Panels
EBU26280 Removing and installing cowlings and panels The cowlings and panels illustrated need to be removed to perform some of the mainte- nance described in this chapter. Refer to this section each time a cowling or a panel has to be removed or reinstalled. 1.
Page 111 EBU26292 Cowling A 4. Remove cowling A by removing the bolts, To remove nuts and washers. 1. Remove cowling B. (See pages 8-9–8-11 for removal and installation procedures.) 2. Remove panel B. (See page 8-12 for re- moval and installation procedures.) 3.
Page 112 To install 1. Connect the speedometer unit couplers. 2. Install cowling A by installing the bolts, nuts and washers. 3. Install panel B. 4. Install cowling B. 1. Bolt (× 3 left side) 1. Bolt (× 3 right side)
Page 113 EBU26330 Cowling B 4. Remove the fuel tank cap by turning it To remove counterclockwise. 1. Remove the seat. (See page 4-13 for CAUTION: seat removal and installation proce- Make sure that no foreign material en- dures.) ters the fuel tank. 2.
Page 114 5. Remove the cowling by removing the bolts. 1. Bolt (left side) 1. Bolt (× 4) 1. Bolt (right side) 8-10...
Page 115 EBU01147 6. Install the fuel tank cap by turning it Panel A clockwise. To remove To install Remove the bolt, and then take the panel off. 1. Remove the fuel tank cap by turning it To install counterclockwise. Place the panel in the original position and in- 2.
Page 116 EBU26350 Panel B To install To remove Insert the tabs on the panel into the slots in Pull outward on the areas shown. cowling A and push inward. 1. Panel B 1. Tab (× 6) 2. Slot (× 6) 8-12...
Page 117 EBU01013 EBU06380 Panel C Panel D To remove To remove Remove the bolts, and then take the panel off. Pull outward on the areas shown. To install Place the panel in the original position, and then install the bolts. 1. Panel D 1.
Page 118: Engine Oil And Oil Filter Cartridge
EBU26340 To install Engine oil and oil filter cartridge Place the panel in its original position. The engine oil level should be checked before each ride. In addition, the oil must be changed and the oil filter cartridge replaced at the inter- vals specified in the periodic maintenance and lubrication chart.
Page 119 1. Engine oil filler cap 1. Maximum level mark 2. Minimum level mark 6. Insert the dipstick in the oil filler hole 7. If the engine oil is at or below the mini- (without screwing it in), and then remove mum level mark, add sufficient oil of the it again to check the oil level.
Page 120 To change the engine oil (with or without NOTE: oil filter cartridge replacement) Skip steps 5–9 if the oil filter cartridge is not being replaced. 1. Remove panel D. (See pages 8-13–8-14 for panel removal and installation proce- 5. Remove panel C. (See page 8-13 for dures.) panel removal and installation proce- 2.
Page 121 8. Install the new oil filter cartridge with an An oil filter wrench is available at a nearby oil filter wrench, and then tighten it to the Yamaha dealer. specified torque with a torque wrench. 7. Apply a light coat of engine oil to the Tightening torque: O-ring of the new oil filter cartridge.
Page 122 Recommended engine oil: See page 10-2. Oil quantity: Without oil filter cartridge replacement: 2.30 L (2.02 Imp qt, 2.43 US qt) With oil filter cartridge replacement: 2.40 L (2.11 Imp qt, 2.54 US qt) CAUTION: 1. Torque wrench In order to prevent clutch slippage 9.
Page 123: Final Gear Oil
EBU11453 12. Start the engine and warm it up for seve- Final gear oil Checking the final gear oil ral minutes. While warming up, check for oil leakage. If oil leakage is found, turn 1. Place the ATV on a level surface. the engine off immediately and check for 2.
Page 124 Replacing the final gear oil 1. Remove the final gear case cover by re- moving the bolts. 1. Final gear oil 2. Final gear oil filler bolt 3. Correct oil level CAUTION: 1. Final gear case cover 2. Bolt (× 2) Be sure no foreign material enters the final 2.
Page 125 Recommended oil: SAE 80 API GL-4 Hypoid gear oil Oil quantity: 0.23 L (0.20 Imp qt, 0.24 US qt) CAUTION: Be sure no foreign material enters the final gear case. 7. Install the oil filler bolt, and then tighten it 1.
Page 126: Differential Gear Oil Replacement
EBU12411 Differential gear oil replacement Tightening torque: 1. Place the ATV on a level surface. Final gear case cover bolt: 2. Place a container under the differential 16 Nm (1.6 m·kgf, 11 ft·lbf) gear case to collect the used oil. 3.
Page 127 5. Fill the differential gear case with the specified amount of the recommended oil. NOTE: Do not exceed the specified differential gear oil quantity when filling. Overfilling will cause the oil to seep out of the breather hose during and after riding. The differential gear oil level cannot be checked.
Page 128: Cooling System
EBU10152 Cooling system CAUTION: 1. Place the ATV on a level surface. Be sure no foreign material enters the dif- 2. Check the coolant level in the coolant ferential gear case. reservoir when the engine is cold as the coolant level will vary with engine tem- 6.
Page 129 You may use soft water if you can not get distilled water. NOTE: If water is added, have a Yamaha dealer check the antifreeze content of the cool- ant as soon as possible. The radiator fan operation is completely 1.
Page 130: Changing The Coolant
EBU26221 Changing the coolant 1. Place the ATV on a level surface. 2. Remove panels C and D. (See pages WARNING 8-13–8-14 for panel removal and installa- POTENTIAL HAZARD tion procedures.) Removing the radiator cap when the en- 3. Place a container under the engine, and gine and radiator are still hot.
Page 131 1. Trough 1. Radiator cap 4. Remove cowling A. (See pages 8-7–8-8 5. Remove the radiator cap. for removal and installation procedures.) 6. Remove the coolant reservoir cap. 7. Disconnect the hose on the coolant res- ervoir side, and then drain the remaining coolant from the coolant reservoir.
Page 132 10. Connect the coolant reservoir hose. 11. Pour the recommended coolant into the reservoir to the maximum level mark, and then install the reservoir cap. 12. Pour the recommended coolant into the radiator until it is full, and then install the radiator cap.
Page 133: Axle Boots
14. Check for coolant leakage. NOTE: If any leakage is found, have a Yamaha deal- er check the cooling system. 1. Axle boot (× 2 each side) 15. Install the cowling.
Page 134: Spark Plug Inspection
EBU14550 Spark plug inspection 2. Use the spark plug wrench in the owner’s Removal tool kit to remove the spark plug as shown. 1. Remove the spark plug cap. 1. Spark plug wrench Inspection 1. Spark plug cap The spark plug is an important engine compo- nent and is easy to inspect.
Page 135 Instead, take the ATV to a Yamaha dealer. You should periodically remove and inspect the spark plug because heat and deposits will cause the spark plug to slowly break down and erode. If electrode erosion becomes ex- cessive, or if carbon and other deposits are excessive, you should replace the spark plug with the specified plug.
Page 136: Air Filter Element Cleaning
EBU15140 Air filter element cleaning NOTE: If a torque wrench is not available when you NOTE: are installing a spark plug, a good estimate of There is a check hose at the bottom of the air the correct torque is 1/4 to 1/2 turn past finger filter case.
Page 137 4. Pull off the lock plate, and then remove the air filter element from its frame. 1. Fastener (× 4) 2. Air filter case cover 3. Remove the air filter element assembly. 1. Air filter element frame 2. Air filter element 3.
Page 138 8. Apply Yamaha foam air filter oil or other WARNING quality foam air filter oil to the air filter el- POTENTIAL HAZARD ement. Using low flash point solvents or gaso- NOTE: line to clean the air filter element. The air filter element should be wet but not WHAT CAN HAPPEN dripping.
Page 139: V-Belt Cooling Duct Check Hose
EBU06411 V-belt cooling duct check hose NOTE: The air filter element should be cleaned every If dust or water collects in the V-belt cooling 20–40 hours. It should be cleaned and lubri- duct check hose, remove the hose and clean cated more often if the machine is operated in extremely dusty areas.
Page 140: V-Belt Case Drain Plug
2. Remove the tailpipe by pulling it out of If water drains from the V-belt case after re- the muffler. moving the plug, have a Yamaha dealer in- spect the ATV as the water may affect other engine parts. 1. Bolt (× 3) 2.
Page 141 WARNING POTENTIAL HAZARD Improper cleaning of the spark arrester. Hot exhaust system WHAT CAN HAPPEN Could injure the eyes. Could cause burns. Could cause carbon monoxide poison- ing, possibly leading to death. 1. Tailpipe 2. Spark arrester Could start a fire. 4.
Page 142: Carburetor Adjustment
NOTE: requires very sophisticated adjustment. Most A diagnostic tachometer must be used for this adjusting should be left to a Yamaha dealer procedure. who has the professional knowledge and ex- 1. Start the engine and warm it up for a few perience to do so.
Page 143: Valve Clearance Adjustment
Select lever safety system cable 1. Throttle stop screw adjustment The select lever safety system cable stretch- es with use, resulting in improper function. To prevent this, the cable must be adjusted regularly. This adjustment, however, should be left to a Yamaha dealer. 8-39...
Page 144: Throttle Lever Adjustment
NOTE: If a brake pad thickness is less than 1.0 mm Adjust the engine idling speed before adjust- (0.04 in), have a Yamaha dealer replace the ing the throttle lever free play. pads as a set. 1. Loosen the locknut.
Page 145: Rear Brake Pad Check
Check the wear indicator grooves. If a brake pad has worn to the point that the wear indicator grooves have almost disappeared, ask a Yamaha dealer to replace the pads as a set. 1. Brake pad wear indicator groove...
Page 146: Inspecting The Brake Fluid Level
EBU26260 Inspecting the brake fluid level FRONT Insufficient brake fluid may let air enter the brake system, possibly causing the brakes to become ineffective. Before riding, check that the brake fluid is above the minimum level mark and replenish when necessary. A low brake fluid level may indicate worn brake pads and/or brake sys- tem leakage.
Page 147: Brake Fluid Replacement
Always clean up spilled the top of the master cylinder reservoirs are fluid immediately. level. Have a Yamaha dealer check the cause if Use only the designated quality brake fluid. the brake fluid level goes down. Otherwise, the rubber seals may deterio-...
Page 148: Front Brake Lever Free Play
The front brake lever should have a free play POTENTIAL HAZARD of zero mm (zero in) at the lever end. If not, Operating with improperly serviced or have a Yamaha dealer check the brake sys- adjusted brakes. tem. WHAT CAN HAPPEN You could lose braking ability, which could lead to an accident.
Page 149: Adjusting The Rear Brake Lever And Brake Pedal
EBU26270 Adjusting the rear brake lever and brake If correct free play cannot be obtained, ask a pedal Yamaha dealer to make that adjustment. Adjusting the rear brake lever NOTE: The rear brake lever free play should mea- When adjusting the rear brake lever free play: sure 0.5–2.0 mm (0.02–0.08 in) as shown.
Page 150 67–77 mm (2.64–3.03 in) above the Operating with improperly serviced or top of the footboard bracket. If not, ask a adjusted brakes. Yamaha dealer to adjust it. WHAT CAN HAPPEN You could lose braking ability, which could lead to an accident.
Page 151: Adjusting The Rear Brake Light Switch
EBU12590 Adjusting the rear brake light switch 2. Turn the adjusting nut while holding the The rear brake light switch, which is activated rear brake light switch in place. To make by the brake pedal and rear brake lever, is the brake light come on earlier, turn the adjusting nut in direction a.
Page 152: Cable Inspection And Lubrication
Inspect cables frequently. Replace dam- aged cables. Lubricate the inner cables and the cable ends. If the cables do not operate smoothly, ask a Yamaha dealer to replace them. Recommended lubricant: Yamaha chain and cable lube or SAE 10W30 motor oil 8-48...
Page 153: Wheel Removal
EBU01112 Wheel removal 1. Loosen the wheel nuts. 2. Elevate the ATV and place a suitable stand under the frame. 3. Remove the nuts from the wheel. 4. Remove the wheel. 1. Nut (× 4) 8-49...
Page 154: Wheel Installation
EBU11211 Wheel installation 1. Install the wheel and the nuts. NOTE: The arrow mark on the tire must point toward the rotating direction of the wheel. Tapered nuts are used for both the front and rear wheels. Install the nut with its ta- pered side towards the wheel.
Page 155: Battery
You may damage the bat- the electrolyte or add distilled water in the bat- tery. tery. If the battery seems to have discharged, consult a Yamaha dealer. WARNING POTENTIAL HAZARD Failure to handle batteries or battery electrolyte carefully.
Page 156: Battery Maintenance
EBU00385 Battery maintenance HOW TO AVOID THE HAZARD 1. When the machine is not used for a Avoid contact with skin, eyes or cloth- month or longer, remove the battery and ing. Always shield eyes when working store it in a cool, dark place. Completely near batteries.
Page 157: Fuse Replacement
Then, install a new fuse of the specified amperage. Turn on the main switch. If the fuse immediately blows again, con- sult a Yamaha dealer. 1. Main fuse 2. Spare main fuse 3. Fuse box...
Page 158 WARNING POTENTIAL HAZARD Using an improper fuse. WHAT CAN HAPPEN An improper fuse can cause damage to the electrical system which could lead to a fire. HOW TO AVOID THE HAZARD Always use a fuse of the specified rat- 1. Headlight fuse 2.
Page 159: Replacing A Headlight Bulb
EBU14721 Replacing a headlight bulb If a headlight bulb burns out, replace it as fol- lows. 1. Remove the headlight bulb holder cover at the rear of the headlight by pulling it off. 1. Headlight bulb holder 1. Headlight bulb holder cover 2.
Page 160 3. Remove the defective bulb from the 4. Install a new headlight bulb into the head- headlight unit by pulling it out. light unit by aligning the projection on the bulb with the groove in the headlight unit. WARNING POTENTIAL HAZARD A headlight bulb is hot when it is on and immediately after it is turned off.
Page 161 5. Install the headlight bulb holder by align- CAUTION: ing the projections with the holes in the Do not touch the glass part of the head- headlight unit, pushing it inward, and light bulb to keep it free from oil, otherwise turning it clockwise until it stops.
Page 162: Headlight Beam Adjustment
EBU12170 Headlight beam adjustment Tail/brake light bulb replacement CAUTION: It is advisable to have a Yamaha dealer make this adjustment. To raise the beam, turn the adjusting bolt in di- rection a. To lower the beam, turn the adjusting bolt in direction b.
Page 163: Troubleshooting
EBU00412 Troubleshooting Although Yamaha machines receive a rigid in- spection before shipment from the factory, trouble may occur during operation. Any prob- lem in the fuel, compression, or ignition sys- tems can cause poor starting and loss of power. The troubleshooting chart describes a quick, easy procedure for making checks.
Page 164 WARNING POTENTIAL HAZARD Checking the fuel system while smok- ing or near an open flame. WHAT CAN HAPPEN Fuel can ignite or explode, causing se- vere injury or property damage. HOW TO AVOID THE HAZARD Do not smoke when checking the fuel system.
Page 165: Troubleshooting Charts
No fuel. 2. Compression There is compression. Compression normal. Use the electric starter to see if there is compression. Ask a Yamaha dealer to No compression. inspect. 3. Ignition Wipe clean with dry cloth. Ignition system is Spark is good.
Page 166: Engine Overheating
Restart the engine. If the engine overheats again, ask a Level is OK. Yamaha dealer to inspect and/or repair the cooling system. NOTE: If it is difficult to get the recommended coolant, tap water can be temporarily used, provided that it is changed to the recommended coolant as soon as possible.
Page 167: Cleaning And Storage
EBU00419 C LEANING AND STORAGE CAUTION: Excessive water pressure may cause wa- A. CLEANING ter seepage and deterioration of wheel Frequent, thorough cleaning of your machine bearings, brakes, transmission seals and will not only enhance its appearance but will electrical devices. Many expensive repair improve its general performance and extend bills have resulted from improper high the useful life of many components.
Page 168 6. Clean the seat with a vinyl upholstery WARNING cleaner to keep the cover pliable and POTENTIAL HAZARD glossy. Operation with wet brakes after wash- 7. Automotive type wax may be applied to ing. all painted and chrome plated surfaces. WHAT CAN HAPPEN Avoid combination cleaner-waxes.
Page 169: Storage
Do not apply oil to fuel) any rubber parts or the seat cover. NOTE: Use of fuel stabilizer and conditioner elimi- nates the need to drain the fuel system. Con- sult a Yamaha dealer if the fuel system needs to be drained instead.
Page 170 7. Remove the battery and charge it. Store it in a dry place and recharge it once a month. Do not store the battery in an ex- cessively warm or cold place (less than 0 °C (30 °F) or more than 30 °C (90 °F)). NOTE: Make any necessary repairs before storing the machine.
Page 171: Specifications
EBU00428 S PECIFICATIONS Model YFM45FXV Dimensions: Overall length 1,978 mm (77.9 in) Overall width 1,063 mm (41.9 in) Overall height 1,095 mm (43.1 in) Seat height 840 mm (33.1 in) Wheelbase 1,233 mm (48.5 in) Ground clearance 220 mm (8.66 in) Minimum turning radius 3,000 mm (118.1 in) Basic weight:...
Page 172 Model YFM45FXV Engine oil: Type 0˚ 10˚ 30˚ 70˚ 90˚ 110˚ 130˚F 50˚ YAMALUBE 4 (20W40) or SAE 20W40 YAMALUBE 4 (10W30) or SAE 10W30 SAE 5W30 -20˚ -10˚ 0˚ 20˚ 30˚ 40˚ 50˚C 10˚ Recommended engine oil classification API Service SE, SF, SG type or higher CAUTION: In order to prevent clutch slippage (since the en- gine oil also lubricates the clutch), do not mix any...
Page 173 Model YFM45FXV Final gear case oil: Type SAE 80 API GL-4 Hypoid gear oil Quantity 0.23 L (0.20 Imp qt, 0.24 US qt) Differential gear case oil: Type SAE 80 API GL-4 Hypoid gear oil Quantity 0.35 L (0.31 Imp qt, 0.37 US qt) Radiator capacity (including all routes): 1.32 L (1.16 Imp qt, 1.40 US qt) Air filter:...
Page 174 Model YFM45FXV Spark plug: Type/manufacturer DR8EA / NGK Spark plug gap 0.6–0.7 mm (0.024–0.028 in) Clutch type: Wet, centrifugal automatic Transmission: Primary reduction system V-belt Secondary reduction system Shaft drive 39/24 × 24/18 × 33/9 (7.944) Secondary reduction ratio Transmission type V-belt automatic Operation Left hand operation...
Page 175 Model YFM45FXV Brake: Front brake type Dual disc brake operation Right hand operation Rear brake type Single disc brake operation Left hand and right foot operation Suspension: Front suspension Double wishbone Rear suspension Swingarm Shock absorber: Front shock absorber Coil spring / oil damper Rear shock absorber Coil spring / oil damper Wheel travel:...
Page 176 Model YFM45FXV Bulb voltage, wattage × quantity: 12 V, 30 W/30 W × 2 Headlight 12 V, 5 W/21 W × 1 Tail/brake light Indicator light: Neutral indicator light Reverse indicator light Coolant temperature warning light Park indicator light Fuses: Main fuse 30 A Headlight fuse...
Page 177: Noise Regulation
EBU00430 N OISE REGULATION TAMPERING WITH NOISE CONTROL SYSTEM PROHIBITED: Federal law prohibits the following acts or the causing thereof: (1) The removal or rendering inop- erative by any person other than for purposes of maintenance, repair, or replacement of any de- vice or element of design incorporated into any new vehicle for the purpose of noise control prior to its sale or delivery to the ultimate purchaser or while it is in use or (2) the use of the vehicle after such device or element of design has been removed or rendered inoperative by any person.
Page 178: Maintenance Record
EBU15740 M AINTENANCE RECORD Copies of work orders and/or receipts for parts you purchase and install will be required to docu- ment maintenance done in accordance with the warranty. The chart below is printed only as a re- minder to you that the maintenance work is required. It is not acceptable proof of maintenance work.
Page 179: Atv Limited Warranty
EBU26310 YAMAHA MOTOR CORPORATION, U.S.A. ATV LIMITED WARRANTY 13-1...
Page 180 13-2...
Page 181: Yamaha Extended Service (Y.e.s.)
EBU00435 YAMAHA EXTENDED SERVICE (Y.E.S.) 14-1...
Page 182 EBU00436 WARNING Indicates a potential hazard that could result in serious injury or death. 14-2...
Page 183 EBU00437...
Page 184 LOCATE AND READ OWNER’S MANUAL. FOLLOW ALL INSTRUCTIONS AND WARNINGS. (For replacement manual, call 1-800-532-1558) YAMAHA MOTOR CO., LTD. PRINTED IN USA 2005.07-1.3×1 CR...

Yamaha WOLVERINE YFM45FXV Owner's Manual

Quick Links

Troubleshooting

Related Manuals for Yamaha WOLVERINE YFM45FXV

Summary of Contents for Yamaha WOLVERINE YFM45FXV

Table of Contents