Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Wavecom TNT+
- Page 1 Australian made to comply with the requirements of the Standard AS/NZS 3760 REVISION 1.11 February 2005 Ph: (08) 8331 8892 Ph: (07) 3274 2466 Int: (+61) 8 8331 8892 Int: (+61) 7 3274 2466 admin@wavecom.com.au sales@nesco.com.au Email: Email www.nesco.com.au www.wavecom.com.au...
-
Page 2: Accessories Supplied
Accessories Supplied (With the Range of TnT Portable Appliance Testers) • Portable Appliance Tester Instruction Manual • Manufacturers Calibration Certificate • IEC Lead • Earth Lead with Alligator Clip • Soft Carry Case Manufacturers Recommendations (For the Range of TnT Portable Appliance Testers) Calibration: The manufacturer recommends a routine calibration verification of readings for determining the accuracy of readings on a 12 Monthly basis. -
Page 3: Table Of Contents
Index Accessories Supplied Manufacturers Reccomendations Index IMPORTANT INFORMATION: Safety Warning The TnT Portable Appliance Tester (Diagram) Competent Person Disclaimer & Limited Warranty TECHNICAL INFORMATION: Class 1 (Earthed Appliance) Construction Class 2 (D/Insulated) Construction Testing of Electrical Equipment 9-10 To Change Test Voltage (250/500VDC Select) INTEGRATED TESTS: SUPPLY MAINS TEST NCNT TEST... -
Page 4: Safety Warning
Safety Warning When using any electrical appliance SAFETY must always be observed. Testing appliances is no exception and in fact MORE care must be taken to ensure personal safety is met. Although the TnT range of products has been designed to meet stringent requirements, no person can be completely protected against the consequences of the incorrect use of an electrical device. - Page 5 The TnT Portable Appliance Tester (Diagram) Display Test Function F1 These buttons are NOT IN USE & are reserved for future functions Test Function F2 Test Function F3 Return/Enter Button Supply Indicator Lights Power Lead IEC Socket Fuse Device Under Test (DUT) Socket [Diagram shown is a sample only and may not be exact to each specific model of TnT Appliance Tester] Page 5...
-
Page 6: Competent Person
Competent Person To ensure that all electrical equipment or devices that are used to perform specific tasks, are inspected and tested and tagged correctly, regulations require that a competent person such as a Licensed Electrician be employed to perform the required tests. A person competent to undertake Inspection and Testing of electrical equipment must therefore have: 1. -
Page 7: Technical Information Class 1 (Earthed Appliance) Construction
Technical Information CLASS 1 (Earthed Appliance) CONSTRUCTION (Single basic insulated and protectively earthed equipment) This type of product design provides two safety barriers between all live conductors at dangerous voltages and the equipment user. The provision of basic insulation between exposed metal parts and live parts is the first barrier to provide basic protection against electric shock. -
Page 8: Class 2 (D/Insulated) Construction
Technical Information Continued CLASS 2 (Double Insulated) CONSTRUCTION (Double insulated equipment) This method of construction employs two safety barriers comprising two layers of insulation between dangerous voltages and the user of the equipment. The first layer of insulation is formed around the live conductor and is termed ‘the Functional Insulation’. -
Page 9: Testing Of Electrical Equipment
Technical Information Continued Testing of Electrical Equipment Many testing personnel have some reservations in testing sensitive, electronic equipment using a 500V DC insulation test. There is a perceived fear of causing internal damage from over voltage. With the introduction on the TnT Range of appliance testers, these concerns are alleviated. -
Page 10: To Change Test Voltage (250/500Vdc Select)
Technical Information Continued Testing of Electrical Equipment 3 Phase Testing: 3 Phase appliances can be tested by the TnT, TnT-el, TnT+ or the TnT-3PL appliance tester. This test is carried out by using the adaptor connection sockets. As the insulation tests are from Phase to Earth, only a 500V insulation test is required. -
Page 11: Supply Mains Test
Integrated Tests Information SUPPLY MAINS TEST The Supply Mains TEST checks the Polarity & Connectivity of the mains supply by LED’s (see below). This test is also a part of all of the testing functions of this unit. A-N, A-E If the N-E (red) light is on and you need to conduct load/leakage tests N - E DO NOT CONTINUE. -
Page 12: Ncnt Test
Integrated Tests Information NCNT TEST (No Connection No Test) The TnT appliance tester ensures that the Device Under Test (DUT) is plugged in and switched on. This test is also a part of all of the testing functions of this unit. This test function ensures that the Device Under Test (DUT) is plugged into the TnT appliance tester and that it is switched on. -
Page 13: Visual Inspection Test
Visual Inspection (FIRST TEST) Information THIS TEST IS TO OCCUR BEFORE ANY OTHER TEST IS CARRIED OUT USING ANY OF THE RANGE OF TnT APPLIANCE TESTERS. In regard to the Device Under Test (DUT), please ensure that; 1. There is no damage or component defect to the accessories, plugs, outlet sockets or connectors (physical). -
Page 14: Tnt Test Function Flow Chart
Chapter 1 – Portable Appliance Part No: WCM-TNT Test Instructions Test Function Flow Chart Main Menu 1 F1 Earth Test F2 D/Ins Test F 3Ext Lead Test F1 Earth Test Supply Mains Test NCNT Test Earth Bond Test Insulation Test Results Summary F2 D/Ins Test Supply Mains Test... -
Page 15: Earthed Appliance Test
Chapter 1 – Portable Appliance Test Instructions EARTHED APPLIANCE TEST Menu 1 For Earthed Appliances CLASS 1 PLEASE NOTE: A VISUAL INSPECTION MUST BE CARRIED OUT BEFORE ANY OTHER TESTS. [refer to page 13 for more details] The EARTHED APPLIANCE TEST completes the following sequence as part of its testing procedure: 1. -
Page 16: Double Insulation Test
Chapter 1 – Portable Appliance Test Instructions DOUBLE INSULATION TEST Menu 1 For Double Insulated Appliances CLASS 2 PLEASE NOTE: A VISUAL INSPECTION MUST BE CARRIED OUT BEFORE ANY OTHER TESTS. [refer to page 13 for more details] The DOUBLE INSULATION TEST completes the following sequence as part of its testing procedure: 1. -
Page 17: Ext Lead Test
Chapter 1 – Portable Appliance Test Instructions EXT LEAD TEST Menu 1 For Extensions Lead/Power Board & IEC Leads PLEASE NOTE: A VISUAL INSPECTION MUST BE CARRIED OUT BEFORE ANY OTHER TESTS. [refer to page 13 for more details] The Ext. Lead TEST completes the following sequence as part of its comprehensive testing procedure: 1. -
Page 18: Tnt-El Test Function Flow Chart
Chapter 2 - TnT-el Portable Appliance Part No: WCM-TNT-EL Test Instructions TnT-el Test Function Flow Chart Please note: Menu 1 is common to all models [TnT, TnT-el & TnT+] Main Menu 1 Menu 2 F1 Earth Test F1Earthed Leakage Test F2 D/Ins Test F2 D/Ins Leakage Test F 3Ext Lead Test... -
Page 19: Tests Common To All Models
Chapter 2 - TnT-el Portable Appliance Test Instructions TESTS COMMON TO ALL MODELS Menu 1 EARTHED APPLIANCE TEST [refer pg 15] DOUBLE INSULATION TEST [refer pg 16] EXT LEAD TEST [refer pg 17] Please note: Menu 1 is common to all models [TnT, TnT-el &... -
Page 20: Standard As/Nzs
Chapter 2 - TnT-el Portable Appliance Test Instructions LEAKAGE TEST Menu 2 The Leakage Test is an alternate method to performing insulation resistance tests. Leakage testing is a major function of the TnT-el & Tnt+ models PLEASE NOTE: A VISUAL INSPECTION MUST BE CARRIED OUT BEFORE ANY OTHER TESTS. - Page 21 Chapter 2 - TnT-el Portable Appliance Test Instructions LEAKAGE TEST [continued] Menu 2 More Information – Leakage Test The Leakage Test allows the user to operate the DUT in normal operation conditions and measure its Operating Leakage current. The displayed parameter is mA: A predefined value for individual class types is programmed into your TnT-el &...
-
Page 22: Tnt+ Test Function Flow Chart
Chapter 3 – TnT+ Portable Appliance Part No: WCM-TNT+ Test Instructions TnT+ Test Function Flow Chart Please note: Menu 1 is common to all models [TnT, TnT-el & TnT+] (refer page 14 for more details) Menu 2 F1 Power Test F2 Leakage Test F3 RCD Test Menu 2... -
Page 23: Tests Common To All Models
Chapter 3 – TnT+ Portable Appliance Test Instructions TESTS COMMON TO ALL MODELS Menu 1 EARTHED APPLIANCE TEST [refer pg 15] DOUBLE INSULATION TEST [refer pg 16] EXT LEAD TEST [refer pg 17] Please note: Menu 1 is common to all models [TnT, TnT-el &... -
Page 24: Power Test
Chapter 3 – TnT+ Portable Appliance Test Instructions POWER TEST Menu 2 The Power Test is for the purposes of monitoring and performance testing the DUT up to the current value 10Amps (resistive load) PLEASE NOTE: A VISUAL INSPECTION MUST BE CARRIED OUT BEFORE ANY OTHER TESTS. - Page 25 Chapter 3 – TnT+ Portable Appliance Test Instructions POWER TEST [continued] Menu 2 More Information re Power Test This test is Ideal for service agents and electricians. The User can plug in the appliance and turn it on with real time measurements displayed on the display. This is useful when testing a DUT with a compliance/name plate on it.
-
Page 26: Rcd Test
Chapter 3 – TnT+ Portable Appliance Test Instructions RCD TEST Menu 2 NOTE: Where ANY RCD testing, is to be carried out any circuit that is protected by an RCD in the main switchboard (upstream), it’s most likely to trip this upstream RCD. When performing RCD trip time or trip current tests on any down stream (portable) RCD devices, the RCD in the switchboard will trip faster. - Page 27 Chapter 3 – TnT+ Portable Appliance Test Instructions RCD TEST [continued] Menu 2 SWITCH BOARD FIXED RCD TnT+ Wall TnT+ Plug DIAGRAM 2 To select the second menu, press and release the RETURN/ENTER Button. This Menu will display 3 functions: Power Test Leakage Test RCD Test...
- Page 28 Chapter 3 – TnT+ Portable Appliance Test Instructions RCD TEST [continued] Menu 2 RCD Trip Time. Press F1 for this option and the following menu appears. Trip Time Testing: This principal is designed to trip RCD devices at a fixed current and to determine the trip time of the RCD device.
- Page 29 Chapter 3 – TnT+ Portable Appliance Test Instructions RCD TEST [continued] Menu 2 The TnT+ displays and maintains the last, set trip current value. If the user wishes to change the value of the trip current the following steps enable the changes.
- Page 30 Chapter 3 – TnT+ Portable Appliance Test Instructions RCD TEST [continued] Menu 2 Press F3 to START test. TnT+ display will display result for 20 seconds after mains supply is tripped. CAUTION Pressing F3 at this point will cause tripping if RCD fitted to circuit TRIP CURRENT TEST.
- Page 31 Specifications for: TnT Portable Appliance Testers Appliance Tester Specifications (for TnT, TnT-el & TnT+ models): Lead continuity and Polarity test @ 240Vac Circuit continuity test 0 – 5MΩ (appliance sense) 15A DUT Socket for Appliance testing only (Not Load Testing) Insulation Voltage 500Vdc + <...
- Page 32 Part No: WCM-TNT+ TnT-elx Portable Appliance Tester Part No: WCM-TNT-ELX TnT-+x Portable Appliance Tester Part No: WCM-TNT+X TnT+P with Lite Base Software Part No: WCM-TNT+P *WinPATS Lite Base Software Part No: WCM-WinPATS Lite Base **WinPATS Lite Software Part No: WCM-WinPATS Lite...
- Page 33 Other Relevant Authorities WorkCover NSW Dept. of Fair Trading – NSW GPO Box 5364 Safety and Standards Branch Sydney NSW 2001-0423 P O Box 972 Australia Parramatta NSW 2124 Ph: 02 4321 5000 Australia Ph: 02 9895 0111 Dept. of Mines and Energy QLD Electrical Safety Office PO Box 69 Brisbane QLD 4001...
- Page 34 Page 34...
- Page 35 Page 35...
- Page 36 Ph: (08) 8331 8892 Ph: (07) 3274 2466 Int: (+61) 8 8331 8892 Int: (+61) 7 3274 2466 admin@wavecom.com.au sales@nesco.com.au Email: Email www.nesco.com.au www.wavecom.com.au Page 36...