Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Instruction Manual
Advertisement
Table of Contents
Related Manuals for VENOM King of Shaves P1
Summary of Contents for VENOM King of Shaves P1
-
Page 2: Safety Precautions
Never leave batteries unattended while charging. If you unsure of how to charge this battery, please contact Venom™ or seek the advice of your local hobby shop. Never let children charge batteries without adult supervision. -
Page 3: Table Of Contents
GENERAL GUIDELINES While the Venom™ King of Shaves P1 35” RTR Electric Boat is incredibly fun, it is not a toy. It is very important that you read and follow the steps detailed in this instruction and radio manual. Failure to follow the guidelines detailed in these manuals could result in damage to property, permanent damage your model, or personal injury. -
Page 4: Required Items
ESC SETUP The watercooled Venom 60A Pro Marine Brushless Speed Control that came in your Venom™ King of Shaves P1 35” RTR Electric Boat is pre-programmed from the factory. If you need to re-program it, please follow the instructions below. - Page 5 ESC SETUP CONT. ESC SETUP CONT. STEP #1. Enter the programming mode. Switch on the transmitter. Move the throttle trigger to the Full throttle position and then connect the battery pack to the ESC. Wait for 2 seconds, the motor emits “Beep-Beep” tone. Wait for 5 seconds, the motor emits a special musical tone noting that the program mode has been entered.
-
Page 6: Batteries
Never leave battery unattended while charging. If you are unsure of how to charge this battery, please contact Venom™ or seek the advice of your local hobby shop. Never let children charge batteries without adult supervision. -
Page 7: Rudder Install
INSTALLING THE RUDDER INSTALLING THE RUDDER 3x3mm Set Screw 3x3mm Set Screw Thread Lock 1. Slide control rod through 2. Apply thread lock and 3. Make sure the servo is 0865 pivot block. tighten the set screw. centered before tightening set screw. -
Page 8: Hatch Install
INSTALLING THE HATCH INSTALLING THE HATCH Secure the hatch by sliding the front pin into the hole at the front of the hull opening. The Hatch should drop easily down so that the magnets hold the hatch securely in place. To waterproof the hatch, use strips of clear tape to seal the lid on all four sides. -
Page 9: Tuning Guide
TUNING GUIDE TUNING GUIDE REPLACING/ UPGRADING THE PROP See page 6 ADJUSTING TRIM TABS The trim tabs are used to adjust the bow angle of the hull and add stability. To adjust the trim tabs tighten or loosen the screw above the tab. For example, tightening the screw will cause the bow of the boat to ride lower suitable for rough conditions. -
Page 11: Maintenance
Hatch - P1KOS 1987 Ball Bearing 4 x 7 - EKOS/P1 KOS/ ME 1917 Drive Shaft Housing - P1KOS 1988 Ball Bearing 4 x 7 Flanged - EKOS/P1 KOS/ ME 1918 Drive Tube - P1KOS 1919 Flex Shaft - P1KOS 1920... -
Page 12: Trouble Shooting
Venom™ warrants this product to be free of material and workmanship defects when new. If a component is defective or was not correctly made, Venom™ will, at its sole discretion, repair or replace it free of charge within 90 days from date of purchase. -
Page 13: Setup Notes
SETUP NOTES SETUP NOTES... - Page 14 SETUP NOTES SETUP NOTES MOTOR & ESC SERVO CG RANGE 210-230mm PROP & DRIVE ANGLES...
- Page 15 BATTERY BOAT WEIGHT AND SETUP SPECS...
-
Page 16: Contact Info
Customer Service Venom Group International Australia customerservice@venom-group.com 14028 N. Ohio Street PO Box 7325 800.705.0620 Rathdrum, ID 83858 Alexandria NSW 2015 208.762.0620 (outside USA) 1816...