Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Texas Instruments 4 PORTS ADSL MODEM/ROUTER
- Page 1 4 PORTS ADSL MODEM/ROUTER User Manual VER:1.1...
-
Page 2: Table Of Contents
Contents Chapter 1: Introduction ..............1 Features ....................1 Supporting protocols ................1 Encapsulation Supports..............1 System requirements................1 Chapter 2: Hardware Installation........... 3 Chapter 3: Modem parameters setting ........... 4 Ethernet over ATM (RFC1483 Bridge) (Bridge) setting ..5 PPP over Ethernet (RFC2516) PPPoE setting...... -
Page 3: Chapter 1: Introduction
Chapter 1: Introduction This device is a well-designed high-speed ADSL modem/router. Features Four 10/100 Ethernet ports Friendly GUI for web configuration. Support Single-Session IPSec and PPTP Pass-Through for Virtual Private Network (VPN) Several popular games are already pre-configured. Just enable the game and the port settings are automatically configured. - Page 4 Protocol Standard User name Password Password protocol LED Status Description INDICATOR STATUS Description POWER Power not supplied Power supplied Ethernet line is connected LAN 1-4 Blink Ethernet traffic is flowing Quick Blink DSL line is training ADSL DSL line is connected DATA Blink DSL traffic is flowing...
-
Page 5: Chapter 2: Hardware Installation
Chapter 2: Hardware Installation Please connect your ADSL MODEM to computer as the following description: If connecting to the splitter, Connect the “Line” splitter to wall jack using one telephone cable Use the other telephone cable to connect “MODEM” port of the splitter and “LINE” port of the modem. The “phone”... -
Page 6: Chapter 3: Modem Parameters Setting
Chapter 3: Modem parameters setting Configuring computer network card IP address Config your network card’s TCP/IP properties to Obtain an IP address automatically to obtain an IP address from modem, or set the computer’s IP with the same network mask of the modem.(For example: modem’s IP is 192.168.1.1/255.255.255.0, Then you can set computer’s IP to: 192.168.1.x/255.255.255.0. -
Page 7: Ethernet Over Atm (Rfc1483 Bridge) (Bridge) Setting
Ethernet over ATM (RFC1483 Bridge) (Bridge) setting To configure the gateway as a bridge, from the Home page, click on Setup and then click on New Connection. The default PPPoE setup is displayed. At the Type field select Bridge and the Bridge connection setup page is displayed. - Page 8 in this case the DSL service provider is using 8,35. Also select the quality of service (QOS); leave the default value if you are unsure or the ISP did not provide this information. Following is a description of the different options: a.
- Page 9 See the following setting: Set VPI/VCI : 0/35 Type: PPPoE Username: username Password: abcd Enforce MTU: select Default Gateway: select Caution: Disable the Enforce MRU function will affect the MSN Messenger usage. Recommend enabling the Enforce MRU when using PPPoE mode. To complete the connection you must now click the apply button.
- Page 10 1. Modify the range of IP address which is needed to reassign. 2. Click Apply to save the configuration 3. To make the change permanent you need to click on Tools and select System Commands. At the system commands page, click on Save All. DHCP Relay The aim of choosing is to set the modem as a repeater in order to make computer get dynamic IP address from ISP.
- Page 11 SNTP SNTP is used for synchronizing computer clocks in the LAN or global Internet. It is strongly recommended that SNTP be used only at the extremities of the synchronization subnet. SNTP clients should operate only at the leaves of the subnet and in configurations where no NTP or SNTP client is dependent on another SNTP client for synchronization.
- Page 12 Using the Port Forwarding page, you can provide local services for people on the Internet or play Internet games. Before enabling Port Forwarding, you should set a IP address and a Hostname in LAN Client. To configure a service, game or other application, select the WAN connection, select the computer hosting the service and add the corresponding firewall rule.
- Page 13 Access Control Open the access from the WAN or LAN to the router's management ports. There are security risks associated with this action. For this reason remote management is restricted to computers on the network specified in the IP Access Control List that can hold up to 16 IP addresses. If enable the access control, you can select WAN or LAN rules which are allowed to access.
- Page 14 User management This feature allows you to change the user name and password and set the idle timeout. Update gateway This feature allows you to get the current configuration and download the configuration document on your computer. It also allows you to upgrade the firmware. Ping test It allows you to test whether the devices are connected.
- Page 15 Modem test This test can be used to check whether your Modem is properly connected to the Network. To perform the test, select your connection from the list and press the Test button. Status The Status section allows you to view the Status/Statistics of different connections and interfaces . Network Statistics Connection status The Connection status displays the connection status, such as link type, IP address, link state, online time and...
- Page 16 Modem status: This window displays the whole information about the modem configurations. Product information: This window displays the product information and software versions. Port bundle PVC port mapping Create New connection with different PVC, see the following.
- Page 17 Click Advanced and PVC bundle. Click the blank to enable PVC bundle, you can configure the connection to each port. For this modem, one port can only bundle on connection which means each port can only bundle one PVC. However, one connection or one PVC can be shared by more than one port.
-
Page 18: Chapter 4: Questions & Answers
Chapter 4: Questions & Answers Question: Why all LED indicators are off? Answer: Check the connection between the power adaptor and the power socket Check the power switch is on or not Question: Why LAN LED is not lighting. Answer: Check the connection between the ADSL modem and your computer or Hub/Switch Check your PC or Hub/Switch running status and make sure them are working normally.
Need help?
Do you have a question about the 4 PORTS ADSL MODEM/ROUTER and is the answer not in the manual?
Questions and answers