Advertisement
®
6 IN 1 AIR FRAMING NAILER
Model 91044
ASSEMBLY and OPERATING
INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
TO PREVENT SERIOUS INJURY,
READ AND UNDERSTAND ALL WARNINGS
AND INSTRUCTIONS BEFORE USE.
©
®
Copyright
2004 by Harbor Freight Tools
. All rights reserved. No portion of
this manual or any artwork contained herein may be reproduced in any shape
or form without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353
Revised 07/04
Advertisement
Table of Contents
Related Manuals for Central Pneumatic 91044
Summary of Contents for Central Pneumatic 91044
- Page 1 . All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions and replacement parts, please call 1-800-444-3353...
-
Page 2: Specifications
ANSI approved dust mask or respirator when working around metal, wood, and chemical dusts and mists. Other people in the work area must also wear ANSI approved impact safety goggles. SKU 91044 For technical questions, please call 1-800-444-3353. Specifications 1/4” NPT... - Page 3 Do not load nails with the trigger or safety depressed. Unintentional firing may occur. Do not load nails when the air hose is connected to the tool. Always assume that the tool contains fasteners. SKU 91044 For technical questions, please call 1-800-444-3353. Page 3...
- Page 4 It must be under- stood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. SKU 91044 For technical questions, please call 1-800-444-3353. Rev 11/06...
- Page 5 When unpacking, check to make sure the parts listed on page 11 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible. 1/4” NPT Nailer You will need to prepare a 1/4”...
-
Page 6: Operation
Note: The Nailer may not work if there are only two or three nails left in the tool. If there are only a few nails remaining, simply load another strip of nails into the Magazine behind the few remaining nails and the Nailer will be ready for further use. SKU 91044 For technical questions, please call 1-800-444-3353. Operation... - Page 7 Exhaust Cover (4) Trigger (47) Air Inlet (90) Magazine (76) FIGURE 3 Angle Adjustment Holes Hex Bolt FIGURE 5 Plate (80) SKU 91044 For technical questions, please call 1-800-444-3353. Operation (continued) Safety (41) Tab (70) FIGURE 6 Pin in Position FIGURE 2...
-
Page 8: Operating The Nailer
Safety (41). Doing so provides a nonslip surface and can improve accuracy. When finished, disconnect the Nailer from the air source. SKU 91044 For technical questions, please call 1-800-444-3353. Operation (continued) Rev 11/06... - Page 9 If you are unable to clear the nail jam using the method prescribed above, the tool should be taken to a qualified service technician for proper servicing. SKU 91044 For technical questions, please call 1-800-444-3353. Figure 7 Probe in these areas with a screwdriver to release jammed nails.
-
Page 10: Troubleshooting
Bottom of tool leaks air Frequent Jamming Note: Contact Harbor Freight Tools for repair/replacement parts. Disconnect the Nailer from the air source hose before attempting any maintenance. Wipe tool clean with a lint free cloth and inspect it for damage. Do not use the tool if you find damage. -
Page 11: Parts List
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts. SKU 91044 For technical questions, please call 1-800-444-3353. Parts List... -
Page 12: Assembly Drawing
Assembly Drawing REV 06/05 SKU 91044 For technical questions, please call 1-800-444-3353. Page 12...