Page 1
For your convenience, record the model number and serial number (you will find them on the rear of your set) in the space provided below. Please refer to them when you contact your AIWA dealer in case of difficulty. Model No. ADC-WRF35, ADC-RF35, ADC-M35 Serial No.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and Configuration of each system used in accordance with the instructions, may ADC-WRF35 cause harmful interference radio Compact disc changer, power unit & FM communications.
PRECAUTIONS • Do NOT install the unit in a location where it • Clean the discs before inserting them into the may be subjected to: disc magazine. Always clean a disc from the — Direct sunlight or other sources of excessive center outward with a cleaning cloth.
UNPACKING Only for ADC-WRF35 Only for ADC-WRF35 and ADC-RF35 Compact disc changer Compact disc magazine Connecting cable Wired remote control Power unit & FM modulator Wireless remote control Tapping screw Double-back tape (medium) Double-back tape (small) for the power unit &...
INSTALLATIONS Precautions Mounting angle setting dials Select the mounting location very carefully, Be sure to change the position of the mounting referring to the following points. angle setting dials according to the angle at which the unit is to be installed. •...
Page 6
INSTALLATIONS Horizontal installation Construction For details on abc..., see page 4. Note If the mounting surface needs to be strengthened, secure the plate brackets d to the bottom surface of the car trunk, etc. with the tapping screws h. Deciding the position Making holes in the carpet Removing temporarily Completion...
Page 7
Vertical installation Construction For details on abc..., see page 4. Note If the mounting surface needs to be strengthened, secure the plate brackets d to the bottom surface of the car trunk, etc. with the tapping screws h. Deciding the position Making holes in the carpet Cut the plate bracket d if it is too long.
Page 8
INSTALLATIONS Suspended installation Caution Before drilling the holes, make sure that there is When installing the unit in the trunk below the nothing on the other side of the mounting surface. package tray, observe the following. • Make sure that the unit is suspended horizontally.
CONNECTIONS Layout and wiring example Car stereo Compact disc Wired remote changer control Power unit & FM modulator Securing the wired and wireless remote control Wired remote control Wireless remote control Double-back tape (small) Where you wish to secure (dashboard etc.) Double-back tape (medium) Where you wish to...
Page 10
CONNECTIONS Connection diagram Fuse To the terminal from which power is supplied when the ignition switch is set to ACC Fuse To an antenna Yellow To the backup terminal from which power is always supplied To a car stereo Black antenna terminal To the vehicle (metal) body Power unit &...
Page 11
Adjustments on the power unit & FM Adjusting the output level The LEVEL control on the power unit & FM modulator modulator is set to the center position, an average level commonly used, at the factory. If necessary, FREQUENCY SELECT adjust the level according to following these switch steps before securing the power unit &...
HOW TO USE How to use a compact disc magazine With the label side up, insert a CD all the way. 6 discs, one in each slot To remove a CD, pull part A in the direction of the arrow as illustrated. Disc magazine z (eject) button Insert the magazine (which has been taken...
Page 13
CD play Turn on your car stereo (not supplied) and select the FM band. Select an appropriate frequency (88.7 or 89.1 MHz). (See page 11 for details.) Press PWR on the wired remote control or POWER on the wireless remote control.
Page 14
HOW TO USE Wired and wireless remote control Wired remote control Wireless remote control 1 Remote sensor 9 INTRO indicator 2 REP (repeat) button 0 DISC number indicator Press to repeat the currently played track. ! TRACK indicator Press again to cancel. @ ONE indicator 3 REP 1 (repeat 1) button Appears when the changer repeats the...
SPECIFICATIONS Error codes Compact disc changer (ADC-M35) System Compact disc digital audio In the following cases the corresponding error system code indication will be displayed. Follow the Frequency response 5 Hz–20 kHz Wow and flutter Below measurable limit suggestions below to solve the problem. If the Signal to noise ratio 97 dB error code indication does not disappear, consult...
Page 16
87-KM1-901-01 970123ATM-OX Printed in Korea...